Pontiac Fiero 1988 Service Manual page 843

7B2-6 5-SPEED (ISUZU) 76MM MANUAL TRANSAXLE
1.
B
10
11
12
13
B
1.
B
2
3
4
5
6
7
8
9
10
11
Remove or Disconnect
Transaxle jack stand.
Install or Connect
Wire harness and coolant pipe on transaxle stud.
Clutch Inspection plate cover.
Speedometer wires on permanent magnet
generator.
Axle shafts. See Section 4D.
Cradle and four bolts front 90 Nnn (67 lb. ft.)
rear 103 N-m (76 lb. ft.).
Rear transmission bracket bolts and align
bracket 54 Nnn (40 lb. ft.).
Motor mount nuts and align mount 57 Nnn (42
lb. ft.).
Engine shock.
Lateral control arm/fixed adjusting link through
bolts, see Section 3D.
Trailing arm, see Section 3D.
Parking brake cables. See Section 5B8 for park-
ing brake adjustment procedure.
Splash shield retainers.
Wheels and tires, see Section 3E.
Remove or Disconnect
Engine support fixture
J 28467-A.
Install or Connect
Upper rear engine support bolt 58 Nnn (43 lb.
ft).
Crossover pipe and wire on oxygen sensor.
Heat shields.
EGR valve output pipe to exhaust manifold.
Clutch slave cylinder to transmission 22 Nnn
(16 lb. ft.) .
Transmission shift cables at transmission.
Intake duct at throttle body from intake elbow.
Fill transmission with fluid.
Deck lid.
Louvered panels.
Negative battery cable.
REAR T R A N S A X L E MOUNT
|+"+| Remove or Disconnect
1. Disconnect negative battery cable.
2. Remove two nuts and wire harness from studs
attaching lower half of transaxle mount to
frame.
3. Install J 28467-A and J 35563 engine support
fixture. Attach fixture hook to engine lift ring
and raise engine enough to take the pressure off
the mount (Figure 5).
4. Four bolts attaching rear transaxle mount to
transaxle.
5. Nut from stud connecting upper and lower halfs
of mount.
B
Install or Connect
1. Nut 48 N-m (35 lb. ft.) connecting upper and
lower mount halfs.
2. Four bolts attaching rear transaxle mount 55
Nnn (41 lb. ft.).
3 Lower engine and remove tools J 28467-A and J
35563.
4. Two nuts and wire harness 48 Nnn (35 lb. ft.)
attaching rear transaxle mount to frame.
5. Negative battery cable.
FRONT TRANSAXLE MOUNT
r + | Remove or Disconnect
1. Negative battery cable.
2. Two bolts attaching upper half of transaxle
mount.
3. Nut from stud attaching coolant pipe to stud and
stud from mount.
4. Install J 28467-A and J 35563 engine support
fixtures. Attach fixture hook to engine lift ring
and raise enough to take the pressure off the
mounts (Figure 5).
5. Two nuts from studs attaching lower half of
mount to frame and remove mount.
6. Nut from stud attaching rear transaxle upper and
lower halfs.
B
Install or Connect
1. Nut on stud 48 Nnn (35 lb. ft.) attaching upper
and lower halfs of transaxle mount.
2. Upper half of transaxle mount with stud 54 Nnn
(40 lb. ft.).
3. Two bolts and one nut on stud 54 N
#
m (40 lb.
ft.) attaching upper half of transaxle mount to
transaxle.
4. Lower engine and remove tools J 28467-A and J
35563.
5. Two nuts on studs 48 Nnn (35 lb. ft.) attaching
lower half of transaxle mount to frame.
6. Negative battery cable.
A X L E SHAFT S E A L S
B
r+|
Remove or Disconnect
1. Axle shaft and inner joint from transaxle, see
Section 4D.
2. Pry out and discard axle shaft seal from
transaxle.
Install or Connect
1. New axle shaft seal with Tool J 26938.
2. Axle shaft and inner joint in transaxle, see Sec-
tion 4D.