Omron SYSDRIVE RX Series User Manual page 353

Item
8 terminals, NO/NC switchable, sink/source logic switchable
[Terminal function] 8 functions can be selected from among 61.
Reverse (RV), Multi-step speed setting binary 1 (CF1), Multi-step speed setting binary 2
(CF2), Multi-step speed setting binary 3 (CF3), Multi-step speed setting binary 4 (CF4),
Jogging (JG), DC injection braking (DB), 2nd control (SET), 2-step acceleration/
deceleration (2CH), Free-run stop (FRS), External trip (EXT), USP function (USP),
Commercial switching (CS), Soft lock (SFT), Analog input switching (AT), 3rd control
(SET3), Reset (RS), 3-wire start (STA), 3-wire stop (STP), 3-wire forward/reverse (F/R),
PID enabled/disabled (PID), PID integral reset (PIDC), Control gain switching (CAS),
UP/DWN function accelerated (UP), UP/DWN function decelerated (DWN), UP/DWN
function data clear (UDC), Forced operator (OPE), Multi-step speed setting bit 1 (SF1),
Multi-step speed setting bit 2 (SF2), Multi-step speed setting bit 3 (SF3), Multi-step
Multi-function input
speed setting bit 4 (SF4), Multi-step speed setting bit 5 (SF5), Multi-step speed setting
bit 6 (SF6), Multi-step speed setting bit 7 (SF7), Overload limit switching (OLR), Torque
limit enabled (TL), Torque limit switching 1 (TRQ1), Torque limit switching 2 (TRQ2),
P/PI switching (PPI), Brake confirmation (BOK), Orientation (ORT), LAD cancel (LAC),
Position deviation clear (PCLR), Pulse train position command input permission (STAT),
Frequency addition function (ADD), Forced terminal block (F-TM), Torque reference
input permission (ATR), Integrated power clear (KHC), Servo ON (SON), Preliminary
excitation (FOC), Analog command on hold (AHD), Position command selection 1 (CP1),
Position command selection 2 (CP2), Position command selection 3 (CP3), Zero return
limit signal (ORL), Zero return startup signal (ORG), Forward driving stop (FOT),
Reverse driving stop (ROT), Speed/Position switching (SPD), Pulse counter (PCNT),
Pulse counter clear (PCC), No allocation (no)
Thermistor input
1 terminal (Positive/Negative temperature coefficient of resistance element switchable)
terminal
5 open collector output terminals: NO/NC switchable, sink/source logic switchable
1 relay (SPDT contact) output terminal: NO/NC switchable
[Terminal function] 6 functions can be selected from among 45.
Signal during RUN (RUN), Constant speed arrival signal (FA1), Over set frequency
arrival signal (FA2), Overload warning (OL), Excessive PID deviation (OD), Alarm signal
(AL), Set-frequency-only arrival signal (FA3), Overtorque (OTQ), Signal during
momentary power interruption (IP), Signal during undervoltage (UV), Torque limit (TRQ),
RUN time exceeded (RNT), Power ON time exceeded (ONT), Thermal warning (THM),
Brake release (BRK), Brake error (BER), 0-Hz signal (ZS), Excessive speed deviation
(DSE), Position ready (POK), Set frequency exceeded 2 (FA4), Set frequency only 2
Multi-function output
(FA5), Overload warning 2 (OL2), Analog FV disconnection detection (FVDc), Analog FI
disconnection detection (FIDc), Analog FE disconnection detection (FEDc), PID FB
status output (FBV), Network error (NDc), Logic operation output 1 (LOG1), Logic
operation output 2 (LOG2), Logic operation output 3 (LOG3), Logic operation output 4
(LOG4), Logic operation output 5 (LOG5), Logic operation output 6 (LOG6), Capacitor
life warning (WAC), Cooling fan life warning (WAF), Starting contact signal (FR), Fin
overheat warning (OHF), Light load detection signal (LOC), Operation ready (IRDY),
Forward run (FWR), Reverse run (RVR), Fatal fault (MJA), Window comparator FV
(WCFV), Window comparator FI (WCFI), Window comparator FE (WCFE), Alarm codes
0 to 3 (AC0 to AC3)
Multi-function monitor Analog voltage output, Analog current output,
output terminal Pulse train output (A-F, D-F {multiplied by "n", pulse output only}, A, T, V, P, etc.)
Output frequency, Output current, Output torque, Frequency conversion value, Trip
Display monitor
record, I/O terminal status, Electric power, etc.
7-1 Standard Specification List
Specifications
7
7-4