Panasonic WJ-SX150 Operating Instructions Manual page 45

• ALARM MODE
You can select an operation mode when alarm input signals
are accepted by the unit.
Note: The alarm mode is activated when alarm input
signals are assigned to the same monitor through
420 ALARM EVENT or the Alarm Event (refer to p.
58) window.
SEQUENCE: An alarm operation is replaced by anoth-
er one after the dwell time (DWELL) ends.
HOLD: An initial alarm operation is continued even after
another alarm input is accepted.
OFF: Select this when not using the alarm mode.
The factory default setting is SEQUENCE.
• DWELL
This stands for the dwell time of a sequence during an
alarm mode.
1 to 30 seconds are selectable.
The factory default setting is 2 seconds.
• ALARM EVENT
This item is configurable in 420 ALARM EVENT.
Move the cursor and press the CAM (SET) button.
420 ALARM EVENT will appear on the monitor.
420 ALARM EVENT
ALM MON MODE
1 1 CAM01
2 1 CAM02
3 1 CAM03
4 1 CAM04
5 1 CAM05
6 1 CAM06
7 1 CAM07
8 1 CAM08
420 ALARM EVENT
ALM MON MODE
9 1 CAM09
10 1 CAM10
11 1 CAM11
12 1 CAM12
13 1 CAM13
14 1 CAM14
15 1 CAM15
16 1 CAM16
ALM: This stands for the alarm number.
MON: This stands for the monitor number.
MODE: This stands for the display mode of an alarm
image.
• CAMnn (nn is the camera number): Activates the
spot camera when an alarm input is accepted.
• PRE: This item stands for the preset position num-
ber of a CAMnn. Enter the desired preset position
number when selecting a combination camera.
When selecting another type of camera, select --.
• TOURnn (nn is a tour sequence number): Executes
a tour sequence when an alarm input is accepted.
The factory default setting is the same as the two illustra-
47
tions above.
1 of 2
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
2 of 2
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
/ PRE--
Notes:
• MODE and PRE cannot be selected by pressing the
numeric buttons. Press the NEXT or PREV button for
selection.
• PRE doesn't appear when TOUR 1 to 16 is selected for
MODE.
• When selecting a camera without the preset position
function, select "- -" for PRE.
• When moving the joystick to
EVENT 1 of 2, the monitor will display 2 of 2 (the next
page).
• When moving the joystick to
EVENT 2 of 2, the monitor will display 1 of 2 (the previ-
ous page).
After the configuration, press the MON (ESC) button. The
monitor display returns to ALARM SETUP.
• ALARM INPUT
CAMERA
ON: This stands for that an alarm input is accepted via
the CAMERA IN connectors or the RS-485 ports.
OFF: This stands for that an alarm input is neither
accepted via the CAMERA IN connectors nor the
RS-485 ports.
The factory default setting is OFF.
ALARM PORT
ON: This stands for that an alarm input is accepted via
the ALARM port (25-pin D-sub connector at the rear
panel).
OFF: This stands for that an alarm input is not accepted
via the ALARM port.
The factory default setting is ON.
Each alarm input's polarity is configurable in 440 ALARM
INPUT (ALARM PORT).
Set ALARM PORT to ON and press the CAM (SET) button.
440 ALARM INPUT (ALARM PORT) will appear on the moni-
tor.
440 ALARM INPUT(ALARM PORT)
1 N.O. 9
2 N.O. 10
3 N.O. 11
4 N.O. 12
5 N.O. 13
6 N.O. 14
7 N.O. 15
8 N.O. 16
To select an alarm input polarity required for the ALARM
port, press the PREV or NEXT button.
N.O.: Selects Normally Open alarm contact.
N.C.: Selects Normally Closed alarm contact.
TIME: Enables the input for time adjustment.
at the bottom of ALARM
at the top of ALARM
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.
N.O.