Daylight Saving Time); Sequence Setup; Alarm Setup - Panasonic WJ-SX150 Operating Instructions Manual

D. S. T. (Daylight Saving Time)
WJ-SX150 SETUP MENU
100 TIME&DATE Au g /21/2002 10:55 AM
200 D.S.T. ON
O
300 SEQUENCE
O
400 ALARM
O
500 CAMERA TITLE
O
600 SYSTEM
700 OPERATOR REGISTRATION
How to Display
To display this menu on the monitor, move the cursor to 200
D. S. T. in SETUP MENU by moving the joystick to
Parameters
Select ON or OFF by pressing the NEXT or PREV buttons.
ON: Daylight saving time is activated.
OFF: Daylight saving time is deactivated.
The factory default setting is ON.
After the configuration, press the SETUP button while hold-
ing down the SHIFT button. The configuration will be updat-
ed when closing SETUP MENU.
Note: The start/end date are configurable through SX150
Admin Console. (Refer to p. 56.)

SEQUENCE SETUP

300 SEQUENCE
TOUR NO. =1
STEP CAM PRE DWELL
1 1 -- 2S
2 2 -- 2S
3 3 -- 2S
4 4 -- 2S
5 5 -- 2S
6 6 -- 2S
7 7 -- 2S
8 8 -- 2S
How to Display
To display this menu on the monitor, move the cursor to 300
SEQUENCE in SETUP MENU by moving the joystick to
.
Then, press the CAM (SET) button. The submenu appears
on the monitor.
Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
46
1.00
O
STEP CAM PRE DWELL
9 9 -- 2S
10 10 -- 2S
11 11 -- 2S
12 12 -- 2S
13 13 -- 2S
14 14 -- 2S
15 15 -- 2S
16 16 -- 2S
TOUR NO: Press the NEXT or PREV button to select the
tour number. Or press the numeric button(s) to
enter a number.
STEP: This stands for a tour sequence step.
CAM: This stands for a camera number. CAM 0 to 16 is
selectable. CAM 0 deactivates the sequence step.
The factory default setting is assigned to each step
in numerical order (STEP 1 = CAM 1, STEP 2 =
CAM 2, STEP 3 = CAM 3, STEP = 4, CAM 4, STEP 5
= CAM 5...)
PRE: This stands for a camera's preset position num-
ber. 1 to 64 or "- -" is selectable. When the camera
has no preset position, select "- -". You can set "- -"
by pressing the button 0.
or .
The factory default setting is "- -".
DWELL: This stands for the dwell time. 1 second to 30
seconds are selectable. If you enter 0, the
sequence step will be skipped.
The factory default setting is 2S for each step.
After the configuration, press the MON (ESC) button. The
monitor display will return to the previous menu.
After all the configurations, press the SETUP button while
holding down the SHIFT button. The configuration will be
updated when closing SETUP MENU.
Notes:
• A preset position number is available only when a com-
bination camera is selected for CAM.
• The available preset position numbers differ among
cameras. Refer to each camera's operating instruc-
tions.

ALARM SETUP

400 ALARM
410 ALARM MODE
420 ALARM EVENT
ALARM INPUT
430
440
450
or
How to Display
To display this menu on the monitor, move the cursor to 400
ALARM in SETUP MENU by moving the joystick to
Then, press the CAM (SET) button. The submenu appears
on the monitor.
Parameters
Move the joystick to move the cursor.
Press the NEXT or PREV button to select the desired para-
meters.
Press the numeric button(s) to enter a number.
SEQUENCE / DWELL 2sec
CAMERA OFF
ALARM PORT ON O
SERIAL PORT ON
or .