Timer Event - Panasonic WJ-SX150 Operating Instructions Manual

Sequence Mode
In the sequence mode, the unit displays the initial alarm
image on the monitor until the dwell time ends, even when
another alarm input is accepted. When the dwell time ends,
the unit automatically replaces the alarm image with the
next one.
Hold Mode
In the hold mode, the unit continues to display the initial
alarm image until the alarm reset. With the alarm image on
the monitor, the unit notifies you that more than one alarm
input is accepted with "*" next to "ALARM nn (nn is the
alarm number)."
Alarm Reset
The built-in timer automatically resets the alarm operation
after the time specified in Setup Utility.
After the reset, the monitor displays and the sequence will
return to the state before the alarm input.
Note: When more than one alarm input has been accepted,
only the newest can be reset.
Alarm Suspension
Even when an alarm signal is input, the system will deacti-
vate the alarm input and the alarm mode.
When the alarm suspension is active, "ALM SUSPENDED"
will appear on the monitor.
Alarm History Table
This table displays the alarms that have occurred in the
past.
The alarm order, date, time, alarm number and event can
be identified.
Up to 100 item can be reserved, and they are overwritten
from the oldest, after more than 100 item have occurred.
Notes:
• When turning off the unit, all the history will be deleted.
• Alarm history can also be identified on the PC.
NO YYYY/MM/DD HH:MM:SS
016 2001/08/21 18:59:08
015 2001/08/21 18:58:08
014 2001/08/21 18:57:08
013 2001/08/21 18:55:08
012 2001/08/21 18:54:08
011 2001/08/21 18:53:08
010 2001/08/21 18:53:00
009 2001/08/21 18:52:08
008 2001/08/21 18:51:08
007 2001/08/21 18:50:08
18
ALARM HISTORY 1 of 2
ALARM EVENT
03 ALARM
03 ACK
03 RESET
07 ALARM
07 ACK
07 RESET
09 ALARM
09 RESET
06 ALARM
06 ACK
Video Loss History Table
While the unit's power is ON, the video signal loss from a
camera or a recorder can occur by cable disconnection,
etc.
In this case, video loss history will be reserved in the sys-
tem, and this table will display the history.
The loss order, date, time, CAMERA IN number and event
can be identified.
Up to 100 item can be reserved, and they are overwritten
from the oldest, after more than 100 item have occurred.
As well as the video loss history, the date of the loss and
recovery, the camera number and the loss status are dis-
played on the table.
Notes:
• When turning off the unit, all the history will be deleted.
• Alarm history can also be identified on the PC.
VIDEO LOSS HISTORY
NO YYYY/MM/DD HH:MM:SS
012 2001/08/21 18:59:08
011 2001/08/21 18:58:08
010 2001/08/21 18:57:08
009 2001/08/21 18:55:08
008 2001/08/21 18:54:08
007 2001/08/21 18:53:08
006 2001/08/21 18:53:00
005 2001/08/21 18:52:08
004 2001/08/21 18:51:08
003 2001/08/21 18:50:08

Timer Event

The built-in timer can automatically start or end the
sequence or spot mode on the specified days, which is
configurable in SX150 Admin Console.
The available operations:
Tour sequence and spot mode
The available timer events:
Up to 30
Note: When displaying SETUP MENU while timer event is
operating, the operation will stop.
1 of 2
CH EVENT
03 VIDEO RECOVER
14 VIDEO RECOVER
09 VIDEO LOSS
07 VIDEO LOSS
08 VIDEO LOSS
16 VIDEO LOSS
09 VIDEO LOSS
14 VIDEO LOSS
06 VIDEO LOSS
01 VIDEO RECOVER