Brocade Communications Systems Brocade 8/12c Reference page 332

18
Bridge-MIB
Object and OID
dot1dStpMaxAge
1.3.6.1.2.1.17.2.8
dot1dStpHelloTime
1.3.6.1.2.1.17.2.9
dot1dStpHoldTime
1.3.6.1.2.1.17.2.10
dot1dStpForwardDelay
1.3.6.1.2.1.17.2.11
dot1dStpBridgeMaxAge
1.3.6.1.2.1.17.2.12
dot1dStpBridgeHelloTim
e
1.3.6.1.2.1.17.2.13
dot1dStpBridgeForwardD
elay
1.3.6.1.2.1.17.2.14
dot1dStpPortTable
1.3.6.1.2.1.17.2.15
dot1dStpPortEntry
1.3.6.1.2.1.17.2.15.1
dot1dStpPort
1.3.6.1.2.1.17.2.15.1.1
dot1dStpPortPriority
1.3.6.1.2.1.17.2.15.1.2
312
Access Description
Read only The maximum age of Spanning Tree Protocol information learned from
the network on any port before it is discarded, in units of hundredths of a
second. This is the actual value that this bridge is currently using.
Read only The amount of time between the transmission of configuration bridge
PDUs by this node on any port when it is the root of the spanning tree, or
trying to become so, in units of hundredths of a second. This is the actual
value that this bridge is currently using.
Read only This time value determines the interval length during which no more than
two configuration bridge PDUs shall be transmitted by this node, in units
of hundredths of a second.
Read only This time value, measured in units of hundredths of a second, controls
how fast a port changes its spanning state when moving towards the
forwarding state. The value determines how long the port stays in each of
the listening and learning states, which precede the forwarding state.
This value is also used when a topology change has been detected and is
underway, to age all dynamic entries in the forwarding database.
Read-write The value that all bridges use for MaxAge when the bridge is acting as
the root. 802.1D-1998 specifies that the range for this parameter is
related to the value of dot1dStpBridgeHelloTime. The granularity of this
timer is specified by 802.1D-1998 to be 1 second. An agent may return a
badValue error, if a set is attempted to a value that is not a whole number
of seconds.
Read-write The value that all bridges use for HelloTime when this bridge is acting as
the root. The granularity of this timer is specified by 802.1D-1998 to be 1
second. An agent may return a badValue error if a set is attempted to a
value that is not a whole number of seconds.
Read-write The value that all bridges use for ForwardDelay when this bridge is acting
as the root. 802.1D-1998 specifies that the range for this parameter is
related to the value of ot1dStpBridgeMaxAge. The granularity of this
timer is specified by 802.1D-1998 to be 1 second. An agent may return a
badValue error if a set is attempted to a value that is not a whole number
of seconds.
Not A table that contains port-specific information for the Spanning Tree
accessible Protocol.
Not A list of information maintained by every port about the Spanning Tree
accessible Protocol state for that port.
Read only The port number of the port for which this entry contains Spanning Tree
Protocol management information.
Read-write The value of the priority field that is contained in the first (in network byte
order) octet of the (2 octet long) Port ID. The other octet of the Port ID is
given by the value of dot1dStpPort.
On bridges supporting IEEE 802.1t or IEEE 802.1w, permissible values
are 0-240, in steps of 16.
Farbric OS MIB Reference
53-1002151-01