JUKI IP-110 Instruction Manual page 47

No.
7 Thread trmmng condensaton nvald selecton
72 Clutch motor functon
73 Retry functon
74 MF thread trmmng devce functon
*
75 Rotatng drecton of motor
*
4 Presser lfter solenod ntal sucton tme
5 Reverse sttchng at the end of sewng start tme
6 Reverse revoluton to lft needle start watng tme
7 Functon of pedal curve selecton
*
9 Tenson release functon
90 Intal UP stop poston move functon
Functon of prohbtng compensaton moton after
*
9
turnng handwheel by hand
Functon of reducng speed of reverse feed sttchng
92
at the start of sewng
Addng functon of needle up/down compensatng
93
sttchng SW
94 Test dsplay mode
Max. number of revolutons
96
(Max. depends on the sewng machne.)
2-ptch output functon (At the tme of reverse feed
00
sttchng at start and end of sewng)
2-ptch nverson output functon (At the tme of
0
alternate vertcal amount output)
02 2-ptch output ntal settng
Number of sttches of alternate vertcal amount output
03
release settng
Automatc up-poston of presser foot at the tme of
04
thread trmmng reverse selecton
05 Needle cooler output OFF delay tme
Pattern control settng
* When No. 76 Clutch motor functon s set to , No.
06 06 Pattern control settng s also changed to .
When returnng to the orgnal state, set No. 06 to
"0" after settng No. 76 to "0".
Alternatve vertcal amount output after thread
07
trmmng selecton
 Grease-up error release settng
Standard set value may, however, change from the aforementioned one depending on the sewing machine used. In addition, function and set
value are subject to be changed without permission to improve function and performance.
Do not change the set value of the functions with * mark since the functions are for maintenance. If the standard set value set at the time of
delivery should be changed, it is very dangerous since breakage or deterioration of the sewing machine will be caused. When it is necessary
to change the standard set value, please purchase the Engineer's Manual and follow the instructions.
Function
– 45 –
Panel display
Setting level
Standard set value
F-TCON
2
F-CMOT
2
F-RET
2
MFTRM
2
2
2
T-WAIT
2
T-WRR
2
F-PCS
2
2
2
F-PMAT
2
F-DSBT
2
F-MADF
2
F-TEST
2
S-MAX
2
F-2PBT
2
F-2PDL
2
2
N-DLOF
2
F-RAFL
2
T-DNCOFF
2
F-PATT
2
F-ATBO
2
GN-CLR
2
Setting range
0 / 

0 / 
0
0 / 

0 / 
0
DM
0 / 

T-PUT
50 to 500
250
0 to 250
50
0 to 250
00
0 /  / 2
0
TRS
0 / 
0
NUO
0 / 
0
0 / 

0 / 
0
0 / 
0
0 / 
0
50 to Max
3500
0 / 
0
0 / 
0
2PINI
0 / 
0
0 to 30
0
0 / 
0
0 to 2000
500
0 / 
0
0 /  / 2
0
0 / 
0