JUKI IP-110 Instruction Manual page 46

No.
Speed of one-shot
3
(Max. depends on sewng machne used.)
39 Revoluton start pedal stroke
40 Low speed secton of pedal
4 Poston where pedal presser lfter starts lftng
*
42 Poston where cloth presser starts lowerng
*
43 Pedal stroke 2 of start of thread trmmng
*
44 Pedal stroke reachng max. number of revolutons
*
45 Compensaton of neutral pont of pedal
*
46 Power ON presser lftng functon
47 Holdng tme of auto-lfter lftng
*
4 Pedal stroke  of start of thread trmmng
49 Presser lowerng tme
50 Pedal presser lftng functon
Compensaton of solenod ON tmng of reverse feed
5
sttchng at the start of sewng
Compensaton of solenod OFF tmng of reverse feed
52
sttchng at the start of sewng
Compensaton of solenod OFF tmng of reverse feed
53
sttchng at the end of sewng
54 Motor pulley effectve dameter
55 Functon of lftng cloth presser after thread trmmng
Functon of reverse revoluton to lft needle after
56
thread trmmng
57 Bobbn thread remanng amount detecton functon
Functon of holdng up/down predetermned poston
5
of needle bar
Functon of A/M changeover of reverse feed sttchng
59
at the start of sewng
Functon of reducng speed of reverse feed sttchng at
60
the start of sewng
Bobbn thread remanng amount detecton ar blow
6
output tme
63 Te sttch adjust functon
64 EBT changeover speed
67 Auto-hemmer control changeover
Materal end sensor of auto-hemmer control start
6
prohbton
Selecton of materal end sensor speed control of
69
auto-hemmer control
Number of sttches of nvald materal end sensor of
70
auto-hemmer control
Standard set value may, however, change from the aforementioned one depending on the sewing machine used. In addition, function and set
value are subject to be changed without permission to improve function and performance.
Do not change the set value of the functions with * mark since the functions are for maintenance. If the standard set value set at the time of
delivery should be changed, it is very dangerous since breakage or deterioration of the sewing machine will be caused. When it is necessary
to change the standard set value, please purchase the Engineer's Manual and follow the instructions.
Function
– 44 –
Panel display
Setting level
Standard set value
2
2
2
2
2
P-TRM2
2
2
2
F-FLPO
2
2
P-TRM
2
T-FLWT
2
2
2
T-SOFF
2
T-EOFF
2
PCDMP
2
2
RATRM
2
2
2
2
2
T-BTDB
2
T-STCP
2
S-WAIT
2
2
2
F-AHSP
2
N-AHOF
2
Setting range
S-ASS
50 to Max
500
P-SSP
0 to 50
30
P-LSA
0 to 00
60
P-FLW
– 60 to – 0
–2
P-FLD
 to 50
0
– 60 to – 0
–5
P-MAX
0 to 50
50
P-ANP
– 5 to 5
0
0 / 
0
T-FL
0 to 600
60
– 60 to – 0
–35
0 to 250
40
PFL
0 / 

T-SON
– 36 to 36
25
– 36 to 36
−7
−36 to 36
−12
500 to 400
50
FLAT
0 / 

0 / 

BTDF
0 to 4

HPOS
0 to 3
0
SBTO
0 / 

SBTQ
0 / 
0
0 to 2000
500
0 to 000
0
0 to 250
0
F-AH
0 / 

F-AHS
0 / 

0 / 

0 to 500
0