JUKI IP-110 Instruction Manual page 32

[Simplified program information input setting code list and connector location list]
The list below is the list of input/output port codes that are set in the second screen of the simplified program
edt, the numbers of connectors and pn assgnment on the crcut board, functons, etc.
Input list
Port nput
Sgnal name
code
0 −
 op0
2 op
3 op2
4 op3
5 op4
6 op5
7 op6
 op7
9 opo0 Input of optonal output 
0 opo Input of optonal output 2
 opo2 Input of optonal output 3
2 opo3 Input of optonal output 4
3 opo4 Input of optonal output 5
4 opo5 Input of optonal output 6
5 opo6 Input of optonal output 7
6 opo7 Input of optonal output 
7 TRMD Thread trmmng output
 WPD
9 TLSUBD Thread release output
20 BRD Reverse sttchng output
2 FLD Presser lftng output
22 BZ
23 M_ERR Machne error output
24 S.STATE
25 HSTSW UP/DOWN swtch nput
26 LSSW Low speed swtch nput
27 BTSW Reverse sttchng swtch nput
2 UDET
29 DDET DOWN poston nput
30 UP
3 DOWN
32 SET+
33 SET−
34 TSW Thread trmmng swtch nput
35 FLSW Presser lftng swtch nput
36 FLSW Presser lftng swtch nput
37 HSSW Hgh speed swtch nput
3 op
39 op9
40 op0
4 op
42 op2
43 op3
44 op4
45 op5
46 opo Input of optonal output 9
47 opo9 Input of optonal output 0
4 opo0 Input of optonal output 
49 opo Input of optonal output 2
50 opo2 Input of optonal output 3
5 opo3 Input of optonal output 4
52 opo4 Input of optonal output 5
53 opo5 Input of optonal output 6
(Caution) 1. It is possible to use port input codes 38 to 45 only when IPOP circuit board is mounted.
2. The motion of port input codes 9 to 16 and 46 to 53 is the function that can use the output internally
as the input signal and the signal in the program when using optional output described in the
function.
Connector No.
and pn No. on
Functon
the crcut board
Invald
Optonal nput  CN5-
Optonal nput 2 CN5-
Optonal nput 3 CN5-2
Optonal nput 4 CN5-2
Optonal nput 5 CN5-3
Optonal nput 6 CN5-3
Optonal nput 7 CN5-4
Optonal nput  CN5-4
Wper output
Buzzer output
Stop state output
UP poston nput
UP key nput Operaton panel
DOWN key nput Operaton panel
SET + key nput Operaton panel
SET − key input Operaton panel
Optonal nput 9 CN23-
Optonal nput 0 CN23-
Optonal nput  CN23-2
Optonal nput 2 CN23-2
Optonal nput 3 CN23-3
Optonal nput 4 CN23-3
Optonal nput 5 CN23-4
Optonal nput 6 CN23-4
Pn No.
Input s nvald.
2
3
2
3
2
3
2
3
− − Output sgnal of optonal output  can be nternally nputted.
− − Output sgnal of optonal output 2 can be nternally nputted.
− − Output sgnal of optonal output 3 can be nternally nputted.
− − Output sgnal of optonal output 4 can be nternally nputted.
− − Output sgnal of optonal output 5 can be nternally nputted.
− − Output sgnal of optonal output 6 can be nternally nputted.
− − Output sgnal of optonal output 7 can be nternally nputted.
− − Output sgnal of optonal output  can be nternally nputted.
CN36 
CN36 2
CN36 7
CN36 6
CN37 
− −
CN40 6
− −
CN3 3 CP-60 (Operaton panel)
CN39  Standng machne type
CN36 5
CN33 6
CN33 
− Front cover
− Front cover
− Front cover
− Front cover
CN39 7 Standng machne type
CN36 4
CN39 5 Standng machne type
CN39 9 Standng machne type
2 Extenson crcut board (IPOP crcut board) CN23
3 Extenson crcut board (IPOP crcut board) CN23
2 Extenson crcut board (IPOP crcut board) CN23
3 Extenson crcut board (IPOP crcut board) CN23
2 Extenson crcut board (IPOP crcut board) CN23
3 Extenson crcut board (IPOP crcut board) CN23
2 Extenson crcut board (IPOP crcut board) CN23
3 Extenson crcut board (IPOP crcut board) CN23
− − Output sgnal of optonal output 9 can be nternally nputted.
− − Output sgnal of optonal output 0 can be nternally nputted.
− − Output sgnal of optonal output  can be nternally nputted.
− − Output sgnal of optonal output 2 can be nternally nputted.
− − Output sgnal of optonal output 3 can be nternally nputted.
− − Output sgnal of optonal output 4 can be nternally nputted.
− − Output sgnal of optonal output 5 can be nternally nputted.
− − Output sgnal of optonal output 6 can be nternally nputted.
– 30 –
Remarks