Scan To Remote Pc - Oki MPS4200mb Basic User Manual

Scanning Methods
Press the to select [Select An
7
Application] and then press
Press the to select where to send the
8
scanned document and then press
Press or
9
M
ONO
Memo
If you select [Application], the specified application starts
and the scanned image is displayed on the application.
If you select [Folder], the scanned image is saved in the
specified folder.
If you select [PC-FAX], the application for fax transmission
starts. After sending the scanned image, send a fax with
the fax transmission software on your computer.
WSD Scan connection
Press the <SCAN> key on the Operation
1
Panel.
Place the original on the automatic
2
document feeder or on the scanner glass.
Press the to select [Local PC] and
3
then press .
OK
Check that the [Select A Connecting
4
PC] is selected, and press
Press the to select [From WSD Scan]
5
and then press
Press the to select the destination PC
6
and then press
Press the to select [Duplex Scan]
7
and then press
Press the or
8
[OFF] and then press
Press or
9
M
ONO
Memo
To start the dual-sided scan, turn its setting On and place
the original on the automatic document feeder. If you turn
the dual-sided scan On but place the document on the
scanner glass, you cannot scan the dual sides of document.
When using the scanner application on PC, it will be
scanned by the scanner type of scan profile setup on PC,
regardless of where the document is set or the setting of
[Duplex Scan].
.
OK
.
C
OLOR
.
OK
.
OK
.
OK
.
OK
to select [ON] or
.
OK
.
C
OLOR

Scan to Remote PC

This function launches the Scanner driver from a
utility installed on a PC (ActKey, PaperPort,
Image,Adobe Photoshop CS3, etc.) and starts
.
OK
scanning.
Connect the machine to a computer via USB or a
network.
For PC Scan function, there are three modes;
simple scan mode, secure scan mode and WSD
scan. In simple mode, the scanning can be
started from all computers via USB and Network.
In secure scan mode, the scanning can be
started from only the already registered
computers in the machine via USB and Network.
In WSD Scan, the scanning can be started from
only the already registered computers in the
machine via Network. Only a computer can be
connected at the same time.
Memo
For the following procedure, ActKey will be used as an
example for Windows, and Adobe Photoshop CS3 for Mac
OS X. The items in this manual may differ depending on
the application you are using.
Note
Connect the machine to a computer via USB or a network.
Install an application (ActKey, PaperPort, etc.) and a
scanner driver before starting a scan job. This installation
is NOT required for WSD Scan connection.
If you connect the machine to network, follow these
instructions.
- Set [TCP/IP] setting to [Enable].
- Conform the IP version of the machine to that of your
computer.
- Set up the DNS server.
- Enable the network TWAIN setting.
When in Secure Scan Mode, the administrator needs to
register the computer information for carrying out security
scans from the control panel or the web site beforehand.
For Mac OS X, when carrying out a network scan for the
first time, you need to set the connection target when
using a driver. When you use the driver for the first time,
the connection target selection tool will launch.
You do not need to set the connection target after the first
time.
To operate the MFP in the WSD Scan connection, set the
followings.
- Set the [TCP/IP] setting of the MFP to [Enable].
- Match the IP version between the MFP and the PC.
- Enable the WSD Scan.
- Install the MFP on the PC.
Reference
For details on how to install a scanner driver, refer to
"Installing Scanner Drivers (TWAIN/WIA/ICA Driver)" P.
- 106 -
97.