3d universal edge routers solutions junos os (200 pages)
Summary of Contents for Juniper ERX - RELEASE 11.1.X HARDWARE GUIDE 03-23-2010
Page 1
E Series Broadband Services Routers Hardware Guide Release 11.1.x Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 408-745-2000 www.juniper.net Published: 2010-03-23...
Page 2
Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.
Page 3
AND (B) YOU MAY CONTACT JUNIPER NETWORKS REGARDING LICENSE TERMS. 1. The Parties. The parties to this Agreement are (i) Juniper Networks, Inc. (if the Customer’s principal office is located in the Americas) or Juniper Networks (Cayman) Limited (if the Customer’s principal office is located outside the Americas) (such applicable entity being referred to herein as “Juniper”), and (ii) the person or organization that originally purchased from Juniper or an authorized Juniper reseller the applicable license(s) for use of the Software (“Customer”)
Page 4
(“GPL”) or the GNU Library General Public License (“LGPL”)), Juniper will make such source code portions (including Juniper modifications, as appropriate) available upon request for a period of up to three years from the date of distribution. Such request can be made in writing to Juniper Networks, Inc., 1194 http://www.gnu.org/licenses/gpl.html...
Page 5
agreements relating to the Software, whether oral or written (including any inconsistent terms contained in a purchase order), except that the terms of a separate written agreement executed by an authorized Juniper representative and Customer shall govern to the extent such terms are inconsistent or conflict with terms contained herein.
Table of Contents About the Documentation xiii E Series and JUNOSe Documentation and Release Notes ......xiii Audience ......................xiii E Series and JUNOSe Text and Syntax Conventions ........xiii Obtaining Documentation ................xv Documentation Feedback ................xv Requesting Technical Support ................xv Self-Help Online Tools and Resources ............xvi Opening a Case with JTAC ..............xvi Part 1 Product Overview...
Page 8
Unpacking ERX14xx Models .................21 Unpacking ERX7xx Models and ERX310 Broadband Services Routers ..22 Inspecting Router Components and Accessories ...........22 If You Detect or Suspect Damage ..............23 Contacting Juniper Networks .................23 The Next Step ....................23 Chapter 3 Installing ERX Routers Before You Begin ...................25 Freestanding Installation ................25...
Page 9
Table of Contents Configuring Line Module Redundancy ............46 The Next Step ....................46 Chapter 5 Cabling ERX Routers Cabling Overview ..................47 Required Tools, Wires, and Cables ..............48 Cabling the SRP I/O Module ................49 External Timing Ports ................50 Management Ports ..................52 Connecting to the Network ...............52 Connecting to a Console Terminal ............52 Cabling the Router for Power ................53 Task 1: Turn Off All Router Power ............55...
Page 10
ERX 11.1.x Hardware Guide Part 3 Hardware Maintenance, Replacement, and Troubleshooting Procedures Chapter 8 Maintaining ERX Routers Required Tools and Items ................77 Storing Modules and Components ..............78 Cleaning the System ..................78 Upgrading from Release 5.1.1 or Lower-Numbered Releases to Release 6.x.x or Higher-Numbered Releases ..............78 Upgrading NVS Cards on SRP Modules ............79 Upgrading a System That Contains One SRP Module ......79...
Page 11
Table of Contents Part 4 Appendixes Appendix A System Specifications ERX14xx Models Specifications ..............109 ERX7xx Models Specifications ..............111 ERX310 Broadband Specifications ..............113 Appendix B Installation Guidelines and Requirements Your Preinstallation Responsibilities ............117 Environmental Requirements ..............117 Regulatory Compliances ................118 Safety Guidelines ..................118 ERX310 Broadband Services Router Warnings (AC Model) ....120 ERX310 Power Cord Warnings (AC Model) ........120 Power Cable Warning (Japanese) ............121...
Page 12
ERX 11.1.x Hardware Guide Appendix D Contacting Customer Support and Returning Hardware Contacting Customer Support ..............139 Return Procedure ..................139 Locating Component Serial Numbers ............140 Information You Might Need to Supply to JTAC ...........141 Tools and Parts Required ................142 Returning Products for Repair or Replacement ...........142 Packing Instructions for Returning a Chassis .........142 Appendix E Declaration of Conformity...
If the information in the latest release notes differs from the information in the documentation, follow the JUNOSe Release Notes. To obtain the most current version of all Juniper Networks® technical documentation, see the product documentation page on the Juniper Networks website at http://www.juniper.net/techpubs/...
Page 14
ERX 11.1.x Hardware Guide Table 1: Notice Icons Icon Meaning Description Informational note Indicates important features or instructions. Caution Indicates a situation that might result in loss of data or hardware damage. Warning Alerts you to the risk of personal injury or death. Laser warning Alerts you to the risk of personal injury from a laser.
Page 15
CD-ROMs or DVD-ROMs, see the Offline Documentation page at http://www.juniper.net/techpubs/resources/cdrom.html Copies of the Management Information Bases (MIBs) for a particular software release are available for download in the software image bundle from the Juniper Networks Web site at http://www.juniper.net/...
7 days a week, 365 days a year. Self-Help Online Tools and Resources For quick and easy problem resolution, Juniper Networks has designed an online self-service portal called the Customer Support Center (CSC) that provides you with the following features: Find CSC offerings: http://www.juniper.net/customers/support/...
ERX 11.1.x Hardware Guide ERX14xx Models NOTE: In the E Series documentation, the term ERX14xx models refers to both the ERX1440 and ERX1410 routers. The terms ERX1440 and ERX1410 routers refer to the specific models. See Figure 1 on page 5 and Figure 2 on page 5. The ERX1440 router manages an extremely high volume of network traffic, and uses a 40-Gbps switch route processor (SRP) module, either the SRP-40G or SRP-40G+ module.
ERX 11.1.x Hardware Guide ERX7xx Models NOTE: In the E Series documentation, the term ERX7xx models refers to both the ERX705 and ERX710 routers. The terms ERX705 and ERX710 routers refer to the specific models. See Figure 3 on page 6 and Figure 4 on page 7. The ERX7xx models are robust, high-density routers with less capacity than the ERX14xx models.
Chapter 1: ERX Overview Figure 4: ERX7xx Models, Rear View ERX310 Broadband Services Router The ERX310 router is a low-end platform that supports all of the same services as the ERX7xx and ERX14xx models, but with smaller capacity and scaling capabilities. Like the ERX7xx and ERX14xx models, the ERX310 router uses the same software architecture, providing a single IP entry point into the network with the same IP-based protocols and services that are available on other ERX routers.
Page 24
ERX 11.1.x Hardware Guide Figure 5: ERX310 Router, Front View (AC Model) NOTE: The DC model has blank filler panels in power supply slots. Figure 6: ERX310 Router, Rear View (AC Model) Figure 7: ERX310 Router, Rear View (DC Model) ERX Routers...
Chapter 1: ERX Overview ERX Modules Each system supports an SRP module and a selection of line modules. You can use any line module for access or uplink. Access line modules receive traffic from low-speed circuits, and the system routes the traffic onto higher-speed uplink line modules and then to the core of the network.
Page 26
ERX 11.1.x Hardware Guide configuration storage, and other control plane functions. Each SRP module is a PowerPC-based system with its own memory, nonvolatile disk storage, and power supply. (See Figure 9 on page 10 and Figure 10 on page 11.) Figure 9: SRP Module for ERX7xx and ERX14xx Models ERX Modules...
Chapter 1: ERX Overview Figure 10: SRP Module for ERX310 Router Module Details ERX7xx and ERX14xx models use up to two redundant SRP modules operating in an active/standby configuration. ERX310 router use only one SRP module. An SRP module must be present for any system to boot. SRP modules ranging from 5 Gbps to 40 Gbps can be used in ERX7xx and ERX14xx models.
ERX 11.1.x Hardware Guide NOTE: Some SRP modules require a minimum amount of memory to be used with JUNOSe Release 5.3.0 or a higher-numbered release. See the ERX Module Guide for module specifications. For details about installing SRP modules, see “Installing Modules” on page 31. SRP Module Redundancy SRP module redundancy is available only for ERX7xx and ERX14xx models.
Chapter 1: ERX Overview BNC connectors and wire wraps are available for ERX7xx and ERX14xx models only. For details about installing the SRP I/O module, see “Installing Modules” on page 31. Line Modules Line modules (LM) process data from different types of network connections. For information about available line modules and which SRP modules support specific line modules, see the ERX Module Guide.
The system offers a complete SNMP interface for configuration, status, and alarm reporting. The system supports both Standard and Enterprise MIBs (Management Information Bases). The Juniper Networks E Series Enterprise MIB is ASN.1 notated for easy importing into third-party SNMP management applications. For more information, see JUNOSe System Basics Configuration Guide, Chapter 4, Configuring SNMP.
Chapter 1: ERX Overview ERX7xx and ERX14xx models use a 1:1 redundancy scheme for the SRP module. When two SRP modules of the same type are installed in the chassis, one acts as a primary (active) and the second as a redundant (standby) module. Both SRP modules share a single SRP I/O module located in the rear of the chassis.
ERX 11.1.x Hardware Guide Line Modules NOTE: This section applies to ERX7xx and ERX14xx models only. ERX310 routers do not offer line module redundancy. ERX7xx and ERX14xx models support line module redundancy for several line modules. For details about which line modules support redundancy, see the ERX Module Guide.
Chapter 1: ERX Overview Figure 12: Data Flow When a Spare Line Module Is Active For information about installing modules for line module redundancy, see “Installing Modules” on page 31. For information about configuring and managing SRP module redundancy, see JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
Page 34
ERX 11.1.x Hardware Guide ERX310 router, two cooling fans are located in a tray on one side of the router (Figure 5 on page 8). The system monitors the temperature of each module. If the temperature of a module exceeds the maximum limit, the system immediately goes into thermal protection mode and the modules are powered off.
Page 35
Part 2 Initial Installation Unpacking and Inspecting ERX Routers on page 21 Installing ERX Routers on page 25 Installing Modules on page 31 Cabling ERX Routers on page 47 Powering Up ERX Routers on page 65 Accessing ERX Routers on page 69 Initial Installation...
Unpacking ERX7xx Models and ERX310 Broadband Services Routers on page 22 Inspecting Router Components and Accessories on page 22 If You Detect or Suspect Damage on page 23 Contacting Juniper Networks on page 23 The Next Step on page 23 Before You Begin Before you begin unpacking the router, be sure you have the following tools: A No.
ERX 11.1.x Hardware Guide Remove the three screws that attach each of the two L-brackets to the router. To avoid scratching the router when removing it from the skid, detach one of the L-brackets from the skid by removing the three screws. See Figure 13 on page 22.
Contact your Juniper Networks sales representative or reseller. Contacting Juniper Networks Please contact Juniper Networks at 1-888-314-JTAC (from the United States, Canada, or Mexico) or 408-745-9500 (from elsewhere), or contact your sales representative if you have any questions or concerns. See “Contacting Customer Support and Returning Hardware”...
Page 40
ERX 11.1.x Hardware Guide The Next Step...
Chapter 3 Installing ERX Routers This chapter describes how to install ERX routers in a rack. It contains the following sections: Before You Begin on page 25 Freestanding Installation on page 25 Rack-Mounted Installation on page 26 The Next Step on page 29 Before You Begin Before installing E Series routers, be sure you: Have a plan for installing the routers that takes into consideration future...
ERX 11.1.x Hardware Guide CAUTION: To prevent electrostatic damage to the system and its components, make sure persons handling the router wear an antistatic device. Connectors are located on the I/O modules and the power input module. These modules are installed from the rear of the router. (See Figure 14 on page 26.) See “Cabling ERX Routers”...
Chapter 3: Installing ERX Routers If you install an ERX14xx model above an ERX7xx model or ERX310 router, there is no need to install a plenum between the units because the ERX7xx models and ERX310 routers vent air out the side of the chassis. Install heavier systems, such as an ERX14xx model, on the bottom of the rack.
ERX 11.1.x Hardware Guide WARNING: Three people are required to install the router in a rack: two to lift the system into position and one to screw it to the rack. CAUTION: Evaluate the overall loading of the branch circuit before you install any equipment into a rack.
Chapter 3: Installing ERX Routers Installing the Router To complete the installation of the router in a rack, you need: A No. 2 Phillips screwdriver Depending on the router, up to eight 10-32 x 3/8 Phillips screws (provided with the router) for each router to be installed WARNING: Three people are required to install the router in a rack: two to lift the system into position and one to screw it to the rack.
Page 46
ERX 11.1.x Hardware Guide The Next Step...
Chapter 4 Installing Modules This chapter describes how to install and remove E Series modules. For information about managing installed modules, see JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules. This chapter contains the following sections: Overview on page 31 Safety Guidelines on page 36 Installing SRP I/O and SRP Modules on page 37 Installing Line and I/O Modules on page 40...
ERX 11.1.x Hardware Guide Figure 16: Orientation of Line Modules in ERX Routers ERX7xx model ERX14xx model ERX310 router For details about available line modules and compatibility between line modules and SRP modules, see the ERX Module Guide. Slot Groups The slots in the ERX1410 router and ERX7xx models are divided into groups.
Chapter 4: Installing Modules Figure 17: ERX1410 Slot Groups Slot Groups for the ERX7xx Models A slot group in an ERX7xx model comprises one slot or two adjacent slots. The groups for an ERX7xx model consist of the following slots (Figure 18 on page 33): Slot group 1 Slots 2 and 3 Slot group 2 Slot 4 Slot group 3 Slot 5...
ERX 11.1.x Hardware Guide OC48 Line Modules The ERX1440 router with the SRP-40G+ SRP module supports OC48 line modules. Other ERX routers do not support OC48 line modules. An OC48 line module spans two slots in an ERX1440 router. You can install this line module only in slots 2–3 and slots 4–5.
Page 51
Chapter 4: Installing Modules Figure 19: Connecting the Wrist Strap to the ERX310 Router (Rear) Table 3: Grounding Jack Locations E Series Router Location ERX14xx models Front: inside front bezel in lower-left corner Rear: upper-right corner ERX7xx models Rear: lower-right corner ERX310 router Front: lower-left corner Rear: lower-right corner...
ERX 11.1.x Hardware Guide CAUTION: Be sure to cover every empty slot with a blank filler panel to protect the system from dust or other foreign substances and to ensure proper system cooling. CAUTION: Do not discard the antistatic bag. When a module is not in use, store it in an antistatic bag.
Chapter 4: Installing Modules WARNING: Never attempt to repair parts of modules yourself. Only trained customer service personnel are authorized to service parts. Call Juniper Networks Customer Service to make arrangements to return defective modules for repair. Installing SRP I/O and SRP Modules You must install SRP modules in specific slots in each router.
ERX 11.1.x Hardware Guide NOTE: See the figures in “ERX Overview” on page 3 for module locations. Tighten the module's captive screws using a No. 2 Phillips screwdriver. Turn both screws several times before tightening them completely to allow the module to sit correctly.
Page 55
Chapter 4: Installing Modules Figure 20: Ejectors in the Open Position Slide the module into the chassis by placing it between the guides of the selected slot and pushing the module until it stops. The module stops sliding when the ejectors make contact with the front of the chassis.
ERX 11.1.x Hardware Guide Installing Line and I/O Modules This section describes the procedures for installing line and I/O modules. NOTE: Install the I/O module before you install the corresponding line module; otherwise, the diagnostics fail and the line module's status is listed as inactive when you issue the show version command.
Chapter 4: Installing Modules Guide the module into the chassis by placing it between the guides of the selected slot and pushing the module until it stops. The module stops sliding when the ejectors make contact with the front of the chassis.
ERX 11.1.x Hardware Guide Figure 21: Ejectors in the Closed Position Carefully slide the module out of the chassis. Place the module in its antistatic bag, being careful not to touch module components, pins, leads, or solder connections. Cover the empty chassis slot with a blank filler panel, and tighten the filler panel's captive screws using a No.
Chapter 4: Installing Modules NOTE: The ERX310 router does not support line module redundancy. For line module redundancy to operate, you must install: The line modules, including the spare line module The redundancy midplane The I/O modules, including the spare I/O module For more information, see “Redundancy Features”...
Page 60
ERX 11.1.x Hardware Guide Enter the halt command. See JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules for information about the halt command. WARNING: Turn off the router before you install the redundancy midplane. Working inside the router when it is on can lead to electric shock and serious burns. Turn off the power switches located on the power input module in the rear of the system (Figure 22 on page 45).
Chapter 4: Installing Modules Figure 22: Installing a Redundancy Midplane Installing the I/O Modules To install the I/O modules in a redundancy group: Install the redundancy I/O module in the lowest-numbered slot of the redundancy group. CAUTION: When setting up a redundancy group with line modules, be sure to install the redundancy I/O module in the lowest-numbered slot of the redundancy group.
ERX 11.1.x Hardware Guide The system reboots. Issue the show redundancy command, and verify that the display shows the redundancy hardware. Configuring Line Module Redundancy For information about configuring line module redundancy, see JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules. The Next Step After you install the modules, you can connect cables to the system.
Chapter 5 Cabling ERX Routers This chapter describes how to cable an ERX router. Before you cable the router, ensure that you have completed all installation instructions identified in previous chapters. This chapter contains the following sections: Cabling Overview on page 47 Required Tools, Wires, and Cables on page 48 Cabling the SRP I/O Module on page 49 Cabling the Router for Power on page 53...
ERX 11.1.x Hardware Guide Figure 23: ERX Ports and Connectors (ERX14xx Model Shown) Required Tools, Wires, and Cables Cabling your system takes only a few minutes. You need the following items and those listed in Table 6 on page 49 for proper installation: 1/8–inch flathead screwdriver 3/8–inch wrench or 3/8–inch nut-driver No.
Chapter 5: Cabling ERX Routers #10 (ERX7xx and ERX14xx models) or #8 (ERX310 Broadband Services Router) kep nut to connect the ground (earth) wire to the ground terminal. Power input module wiring We recommend a minimum of 8-AWG wire for ERX14xx models, 12-AWG wire for ERX7xx models, and 14-AWG wire for ERX310 router (DC model) with a dual stud terminal lug with 5/8–inch spacing.
ERX 11.1.x Hardware Guide NOTE: The alarm function on the SRP I/O module is currently not implemented. Only ERX7xx and ERX14xx models have external timing ports and alarm leads located on the SRP I/O module. All ERX routers have console ports located on the SRP I/O module.
Page 67
Chapter 5: Cabling ERX Routers Figure 24: SRP I/O Module for ERX14xx Models To connect the clock source input ports: Depending on the connector type, complete one of the following tasks: E1: Attach the BNC connector to Clock A's external timing port. T1: Wrap the tip wire on pin marked T of Clock A's external timing port, the ground wire on G pin, and the ring wire on R pin.
ERX 11.1.x Hardware Guide Management Ports NOTE: This section applies to all ERX routers. The Console section of the SRP I/O module has two ports for management access. (See Figure 24 on page 51 and Figure 25 on page 52.) The 10/100Base-T Ethernet port accepts an RJ-45 (male) connector, providing an out-of-band connection for LAN access through a Telnet session or SNMP.
Chapter 5: Cabling ERX Routers To connect the console to the SRP I/O module: Insert the female DB-9 connector into the RS-232 port, and tighten the screws. CAUTION: Do not overtighten the screws. Connect the other end of the cable to your terminal's serial port (VT100/ANSI). Cabling the Router for Power After you have correctly cabled the modules and I/O modules, you must attach grounding and electrical wires before you attempt system power-up.
Page 70
ERX 11.1.x Hardware Guide Table 8: Power Input Module Cables and Wires Needed (continued) Cable/Wire From Two 12-AWG wire leads Power input module Power A –48 VDC and Appropriate leads on power source RTN leads No.1 Two 12-AWG wire leads Power input module Power B –48 VDC and Appropriate leads on power source RTN leads...
Chapter 5: Cabling ERX Routers Figure 26: Power Input Module for ERX14xx Models Task 1: Turn Off All Router Power Before starting, you must switch all router power switches to OFF. To turn off the router, push each power switch to the OFF position. Task 2: Connect the Grounding Cables All ERX routers have two grounding studs located in the rear of the chassis, near the power inputs.
ERX 11.1.x Hardware Guide Locate the grounding studs on the router (Figure 26 on page 55 and Figure 27 on page 57). Remove the nuts and locking washers from the grounding studs. NOTE: We recommend a minimum of 10-AWG ground wire with a ring style terminal. Place the grounding cable lead on one of the grounding studs and tighten the nuts to secure the connection.
Chapter 5: Cabling ERX Routers Remove the nuts and locking washers from the posts for the power input (A or B) using a small insulated adjustable wrench. Place one negative (neutral) cable lead on the post labeled –48 VDC. Replace the locking washers and nuts, and tighten the nuts to secure the connection.
ERX 11.1.x Hardware Guide Repeat Steps 1–2 for the other power input module, if needed. Figure 28: ERX310 Router, Rear View (AC model) Cabling I/O Modules This section illustrates the common connector types used with ERX I/O modules. For information about the connectors on the different line modules, see the ERX Module Guide.
Chapter 5: Cabling ERX Routers CAUTION: Do not terminate HSSI connections with SCSI connectors. Although SCSI connectors look very similar to HSSI connectors, using SCSI connectors on HSSI connections can lead to data loss. Figure 30: HSSI I/O Module with 50-Pin HSSI Connector RJ-45 Connectors When inserting an RJ-45 connector, be sure it clicks into the port.
ERX 11.1.x Hardware Guide Figure 32: I/O Module with RJ-48C Connectors LC Duplex Connectors In accordance with EN60825-1, Safety of Laser Products - Part 1: Equipment Class, Requirements, and User's Guide (2001), multimode I/O modules with LC connectors are defined as follows: CLASS 1 LED PRODUCT.
Chapter 5: Cabling ERX Routers WARNING: Do not look directly into SC-style fiber connectors. The fiber-optic laser used in single-mode fiber (SMF) meets the regulatory requirements for casual exposure to the eye; however, looking directly into a laser can cause eye damage. WARNING: IEC 825, Class 1 laser fiber connectors are for connection only to Class 1 laser devices.
ERX 11.1.x Hardware Guide Figure 34: I/O Module with SMB Connectors X.21/V.35 Connectors Four cables are available for the X.21/V.35 I/O modules: X.21 DCE cable (terminated with 8 female X.21 connectors) X.21 DTE cable (terminated with 8 male X.21 connectors) V.35 DCE cable (terminated with 8 female V.35 connectors) V.35 DTE cable (terminated with 8 male V.35 connectors) Each 200-pin proprietary socket on the I/O module provides connections to 8 V.35...
Chapter 5: Cabling ERX Routers Redundant Ports Some modules have redundant ports. See the ERX Module Guide for specifications. Cabling both ports provides a redundant path to the module. CAUTION: For port redundancy to operate correctly on a GE I/O module that supports SFPs, both the primary and redundant ports on an E Series GE I/O module must use the same type of SFP.
Page 80
ERX 11.1.x Hardware Guide The Next Step...
Chapter 6 Powering Up ERX Routers This chapter describes how to power up an ERX router and determine whether it has booted properly. It contains the following sections: Before You Power Up the System on page 65 Powering Up on page 65 Status LEDs on page 66 Powering Down on page 67 The Next Step on page 67...
ERX 11.1.x Hardware Guide CAUTION: Evaluate the overall loading of the branch circuit before you install any equipment into a rack. To power up the system: Verify that the power source is operational and turned on. Inspect all grounding and power connections to the router chassis. Confirm that all connections are secure.
Chapter 6: Powering Up ERX Routers Powering Down If you need to power down or remove the SRP module, first enter the halt command to temporarily suspend the system's operation. See JUNOSe System Basics Configuration Guide, Chapter 5, Managing the System for more information. CAUTION: If you do not use the halt command before removing or powering down an SRP module, the system's NVS card might become corrupted.
Page 84
ERX 11.1.x Hardware Guide The Next Step...
Chapter 7 Accessing ERX Routers This chapter discusses how to access the system to manage it. Managing your router includes both configuring and monitoring it. For basic information on the management of the system, see JUNOSe System Basics Configuration Guide, Chapter 5, Managing the System.
ERX 11.1.x Hardware Guide To communicate with the system, you must have a terminal emulation program running on your PC or Macintosh. You can use any terminal emulation program, such as HyperTerminal. A UNIX workstation can use the emulator TIP. Using HyperTerminal If your console uses a version of Microsoft Windows (such as Windows 95 or Windows NT 4.0) that supports the HyperTerminal application, you can access the system via...
Chapter 7: Accessing ERX Routers Figure 36: Management Ports for ERX Routers ERX310 router ERX14xx models ERX7xx models Connect the crossover adapter connector to your PC's serial port. Power up the system. When you power up the system, the CLI appears on your console's screen. The system is now in User Exec mode, and you can begin configuration.
ERX 11.1.x Hardware Guide Use an IP address valid for the system. host1#configure terminal Enter configuration commands, one per line. End with CNTL/Z. host1(config)#interface FastEthernet slotnumber/0 host1(config-if)#ip address 10.10.7.3 255.255.255.0 Continue to configure the system's parameters as needed. After you have assigned an IP address to the system, you can communicate remotely by running Telnet over an Ethernet network.
Chapter 7: Accessing ERX Routers NOTE: In this example, you disabled the password requirement, but you can choose to set a password instead. See JUNOSe System Basics Configuration Guide, Chapter 8, Passwords and Security for information on setting a password. Run Telnet from a host on the same Ethernet network as the system.
Page 90
ERX 11.1.x Hardware Guide The Next Step...
Page 91
Part 3 Hardware Maintenance, Replacement, and Troubleshooting Procedures Maintaining ERX Routers on page 77 Troubleshooting on page 95 Hardware Maintenance, Replacement, and Troubleshooting Procedures...
This chapter lists the tools, items, and steps needed for installing and uninstalling ERX router components. Other maintenance procedures must be performed by an authorized Juniper Networks technician. This chapter contains the following sections: Required Tools and Items on page 77...
ERX 11.1.x Hardware Guide Storing Modules and Components Retain the packaging in which a module or component was shipped, and use this packaging to store the item. Modules are shipped in antistatic bags and protective packaging. Components, such as transceivers and nonvolatile storage (NVS) cards, are shipped in antistatic plastic containers within an antistatic padded box.
Chapter 8: Maintaining ERX Routers This enables the system to support application images greater than 172 MB. For example, you cannot go from Release 5.1.1 to Release 7.2.0 without first upgrading to Release 5.1.2. See the following table for compatibility of releases. Maximum Application JUNOSe Release Highest Release Able to Load...
ERX 11.1.x Hardware Guide Enter the halt command. See JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules for information about the halt command. WARNING: Do not insert any metal object, such as a screwdriver, or place your hand into an open slot or the backplane when the router is on. Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
Chapter 8: Maintaining ERX Routers Remove the redundant SRP module from the chassis. Replace the NVS card on this SRP module. (See “Replacing an NVS Card” on page 81.) Reinsert the SRP module into the chassis. When this SRP module is available, synchronize the SRP modules. host1#synchronize When the SRP modules are synchronized, reboot the SRP module that you upgraded.
ERX 11.1.x Hardware Guide Figure 37: NVS Card Slot on SRP Module Remove the NVS card and place it in the antistatic container. Insert the new NVS card into the slot, and push it until it clicks into place. Replace the faceplate on the NVS card slot. Upgrading Memory on SRP Modules This section describes how to upgrade memory on SRP modules.
Chapter 8: Maintaining ERX Routers CAUTION: When handling modules, use an antistatic wrist strap connected to the router's ESD grounding jack, and hold modules by their edges. Do not touch the components, pins, leads, or solder connections. These actions help to protect modules from damage by electrostatic discharge.
Page 100
ERX 11.1.x Hardware Guide Locate the four SODIMM sockets on the SRP module. (See Figure 38 on page 84 and Figure 39 on page 84.) See the previous section to learn how to remove SODIMMs. Figure 38: SODIMM Sockets on the SRP-5 and SRP-10 Module Figure 39: SODIMM Sockets on the SRP-40 Module Insert a SODIMM from the upgrade kit at an angle of approximately 45 degrees into an empty ceramic connector, so that the notch in the long gold edge of the...
Chapter 8: Maintaining ERX Routers Repeat Steps 2–3 with the other SODIMM. Repeat Steps 1–4 for the other SRP module, if present. Verifying the Upgrade To verify that the upgrade is complete: Place the SRP modules in the chassis. The SRP modules reboot. Close the ejector handles and tighten the thumbscrews.
ERX 11.1.x Hardware Guide Identify the release mechanism for the SFP. Different SFPs use different release mechanisms. (See Figure 40 on page 86.) Possible release mechanisms include: A button that you press inward A ring that you press inward A bar that you pull sideways, then outward A tab that you pull sideways, then outward Figure 40: Possible Release Mechanisms on the SFP Release the SFP and pull it out of the slot.
Page 103
Chapter 8: Maintaining ERX Routers Figure 41: Example of SFP CAUTION: Be sure to position the SFP correctly before you install it. Hold the SFP so that: The connection circuitry is adjacent to the TX and RX markings on the module's faceplate.
ERX 11.1.x Hardware Guide If you are using the redundant port on the GE I/O module, repeat Steps 2–7 for the other port. Verifying the Installation After you have replaced the SFPs and connected the cables, issue the show interface gigabitEthernet command for each interface to make sure that the interface is operational (up).
Page 105
Chapter 8: Maintaining ERX Routers CAUTION: Do not use the fan tray handle to carry the fan tray assembly. Use the handle only to pull the tray out of the chassis. Figure 43: Fan Tray in ERX14xx Models Figure 44: Fan Tray in ERX7xx Models Replacing Fan Trays...
ERX 11.1.x Hardware Guide Figure 45: Fan Tray in ERX310 Router Removing the Fan Tray To remove the fan tray: (ERX14xx models only) Place a flathead screwdriver in the groove where the top bezel meets the chassis on the top of the system, and lever the top bezel off the front of the system.
Chapter 8: Maintaining ERX Routers Hold the tray horizontally (ERX14xx models) or vertically (ERX7xx models and ERX310 router) or so that the captive screws point toward you and you can read text on the labels. Place the bottom corners of the tray housing in the plastic shelf guides of the fan tray compartment;...
ERX 11.1.x Hardware Guide Figure 46: Installing an Air Filter into an ERX14xx Router To install an air filter: Ground yourself by using an antistatic wrist strap or other device and connect it to one of the ESD grounding jacks. Remove the front bezel by grabbing the edges and pulling straight out toward you.
Chapter 8: Maintaining ERX Routers For wider X.21/V.35 cables, mount the bracket in the last row of perforation holes in the chassis so that the bracket allows for maximum spacing (A). For smaller cables, mount the bracket closer to the front of the chassis (B). Use two (2) #10 self-tapping screws to secure the bracket.
Page 110
ERX 11.1.x Hardware Guide Install the new PIM and tighten the screws. CAUTION: Do not overtighten the screws. Reconnect the power cables and grounding cables. See “Cabling the Router for Power” on page 53 Replace the clear plastic guard. Power up the router. See “Powering Up ERX Routers” on page 65. Figure 48: Power Input Module for ERX14xx Models Replacing a Power Input Module...
Chapter 9 Troubleshooting This chapter explains how you can troubleshoot a specific problem, such as abnormal LED activity or no system power, when you power up the router. It contains the following sections: Diagnosing Problems on page 95 Troubleshooting Power Failures on page 96 Understanding Status LEDs to Troubleshoot on page 96 Monitoring Temperatures of Modules on page 103 Resetting Line Modules and SRP Modules on page 104...
See “System Specifications” Power source cannot handle on page 109. system load. If the system still does not operate, contact Juniper Networks Customer Service. System shuts Temperature is too high. The following actions apply to all of the possible problems: down.
Page 113
Chapter 9: Troubleshooting For example, an OCx/STMx line module can pair with either an OC3-4 or an OC12/STM4 I/O module. Consequently, the line module has four port status LEDs for OC3/STM1 operation. However, only the top set of port status LEDs is active during OC12/STM4 operation.
Page 114
ERX 11.1.x Hardware Guide Table 10: LED Identification and Activity Descriptions (continued) Location LED Label LED Indicator LED Color OFF to ON ON to OFF HSSI line SYNC Port status Green If the port is configured as If the port is configured as module DTE, the LED lights when both DTE, the LED goes out when...
Page 115
Chapter 9: Troubleshooting Figure 49: SRP Module LEDs NOTE: The primary SRP module illuminates the REDUNDANT LED only when the SRP module detects a secondary or standby SRP module online. The standby SRP module monitors an activity signal from the primary SRP module to determine its state;...
ERX 11.1.x Hardware Guide Figure 50: FE2 Module LEDs Figure 51: E3 and T3 Module LEDs LED Activity When the system boots, it runs a series of tests for each module installed in the system, and the LEDs display various configurations. See Table 11 on page 101 and Table 12 on page 101 to understand normal and abnormal LED activity.
Page 117
Power B. Make sure connections to power sources are securely attached. If system still does not operate, contact Juniper Networks Customer Service. FAIL LED lights The line module and I/O Make sure that the line modules and I/O modules are module are incompatible.
Page 118
Table 12: Troubleshooting Abnormal LED Activity on Modules (continued) Diagnostic Signs Possible Problems Actions FAN OK LED does Fan is not working properly Contact Juniper Networks Customer Service; the system must not light or has slowed down. be serviced. FAN FAIL LED lights Fan needs replacement.
Chapter 9: Troubleshooting Redundancy Status You can determine the redundancy state of line modules by examining the ONLINE and REDUNDANT status LEDs (ERX7xx and ERX14xx models only). See Table 13 on page 103. NOTE: The REDUNDANT LED on the cOCx/STMx, FE-8, GE/FE, HSSI, and OCx/STMx modules is nonfunctional.
ERX 11.1.x Hardware Guide Table 14: Troubleshooting High-Temperature Conditions (continued) Cause of High Operating Temperature Symptoms Resolution Cooling fan failure FAN OK LED on SRP module is not Replace fan tray. (See “Maintaining ERX illuminated. Routers” on page 77.) FAN FAIL LED on SRP module is illuminated.
SRP module after you reboot, or if the FAIL LED on the SRP module stays on during rebooting, the SDRAM is permanently damaged and needs replacing. In this event, call Juniper Networks Customer Service to arrange for repair.
Page 123
Part 4 Appendixes System Specifications on page 109 Installation Guidelines and Requirements on page 117 Cable Pinouts on page 131 Contacting Customer Support and Returning Hardware on page 139 Declaration of Conformity on page 145 Appendixes...
Appendix A System Specifications This appendix lists the system specifications, requirements, and certifications for ERX routers. ERX14xx Models Specifications on page 109 ERX7xx Models Specifications on page 111 ERX310 Broadband Specifications on page 113 ERX14xx Models Specifications Table 15: ERX14xx Models Specifications Category Specification Weights are approximate.
Page 126
ERX 11.1.x Hardware Guide Table 15: ERX14xx Models Specifications (continued) Category Specification Current 50 A @ –48 VDC Power 2400 W maximum Redundancy (input power) 2 independent line feeds 3 feet (90 cm) behind router or rack Space Requirements No space requirements for sides of units or rack Do not block air vents on top, front, or back of the router An integral air plenum directs router's exhaust air below the router and out the back.
Appendix A: System Specifications Table 15: ERX14xx Models Specifications (continued) Category Specification ACA TS 016-1997 Telecommunications Certification CTR13 – Commission Decision of 9 July 1997 on a common technical regulation for attachment requirements for terminal equipment interface for connection to 2048 kbit/s digital structured ONP leased lines: 97/521/EC –...
Page 128
ERX 11.1.x Hardware Guide Table 16: ERX7xx Models Specifications (continued) Category Specification Current 30 A @ –48 VDC Power 1400 W maximum Redundancy (input power) 2 independent line feeds 3 feet (90 cm) behind router or rack Space Requirements Do not block air vents on sides of the router. Do not place equipment that exhausts hot air to left on the right of the router.
Appendix A: System Specifications Table 16: ERX7xx Models Specifications (continued) Category Specification ACA TS 016-1997 Telecommunications Certification CTR13 – Commission Decision of 9 July 1997 on a common technical regulation for attachment requirements for terminal equipment interface for connection to 2048 kbit/s digital structured ONP leased lines: 97/521/EC –...
Page 130
ERX 11.1.x Hardware Guide Table 17: ERX310 Router Specifications (continued) Category Specification Ambient storage temperature –40° to 158° F (–40° to +70° C), 95% relative humidity Ambient storage humidity 5% to 95% (noncondensing) 500 W, 1706 BTU/hour maximum Heat Dissipation DC Input Voltage –40 to –72 VDC...
Page 131
Appendix A: System Specifications Table 17: ERX310 Router Specifications (continued) Category Specification AS/NZS 60950:2000 Safety of Information Technology Equipment Safety Agency Certification CAN/CSA-C22.2, No. 60950-1–03, First Edition, Information Technology Equipment - Safety - Part 1: General Requirements EN60825-1, Safety of Laser Products - Part 1: Equipment Class, Requirements, and User's Guide (2001) EN60950-1:2001, First Edition, Information Technology Equipment - Safety - Part 1: General Requirements...
Appendix B Installation Guidelines and Requirements This chapter reviews preinstallation considerations such as electrical, environmental, and safety compliances for ERX routers. For complete system specifications, see “System Specifications” on page 109. This chapter contains the following sections: Your Preinstallation Responsibilities on page 117 Environmental Requirements on page 117 Regulatory Compliances on page 118 Safety Guidelines on page 118...
ERX 11.1.x Hardware Guide Choose a location for the router that is dry, relatively dust free, well ventilated, and air conditioned. If you install equipment in a rack, be sure that the floor is capable of supporting the combined weight of the rack and the installed equipment. Place the router in a location with sufficient access to power and network cables.
Page 135
Appendix B: Installation Guidelines and Requirements WARNING: Do not work on the system or connect or disconnect cables during lightning activity. WARNING: Be sure circuit breakers for the power source are in the OFF position before attaching power cables. WARNING: Before servicing the router, turn off the power. WARNING: Remove jewelry (including rings, necklaces, and watches) before working on equipment that is connected to power lines.
ERX 11.1.x Hardware Guide ERX310 Broadband Services Router Warnings (AC Model) The following warnings apply only to the ERX310 router. ERX310 Power Cord Warnings (AC Model) WARNING: This unit has more than one power-supply cord. Disconnect 2 power cords BEFORE servicing to avoid electric shock. Denne enhed har mere end een strømfordelingsledning.
Appendix B: Installation Guidelines and Requirements Power Cable Warning (Japanese) WARNING: The attached power cable is only for this product. Do not use the cable for another product. Equipment Rack Requirements When allocating equipment rack space, consider the following: Type of equipment racks recommended for ERX routers Number of equipment racks required to hold your current router configuration Future expansion Make sure your distribution rack meet basic mechanical and space requirements...
ERX 11.1.x Hardware Guide Figure 52: ERX Routers Installed in a Rack ERX310 router ERX7xx model Plenum ERX14xx model Mechanical Requirements Follow these mechanical requirements for your rack: Select from the following rack options: Two-post rack A freestanding enclosed cabinet with two mounting posts in the front Telco-type rack Two adjacent mounting posts that you must secure to the floor or an overhead structure...
A fully loaded rack with three ERX14xx models must structurally support 300 pounds (136 kilograms). Optional mounting kits are available for 19-inch and 23-inch rack mounting (mid-chassis and front-chassis mounting). Contact your Juniper Networks sales representative for more information. Space Requirements If you use an enclosed rack for an ERX14xx model, ensure that there is a minimum of 3 inches of clearance between the inner side wall and the router.
ERX 11.1.x Hardware Guide Figure 53: Airflow for ERX Routers Cabling Recommendations Comply with the following recommendations: Use only shielded cables. Ensure that cable distance and rate limits meet IEEE-recommended maximum speeds and distances for signaling purposes. For information about attenuation and power loss in optical fiber cables see: ANSI T1.646a-1997 Telecommunications –...
Product Reclamation and Recycling Program Juniper Networks is committed to environmentally responsible behavior. As part of this commitment, we continually work to comply with environmental standards such as the European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive and Restriction of Hazardous Substances (RoHS) Directive.
ERX 11.1.x Hardware Guide Products returned through our reclamation process are recycled, recovered, or disposed of in a responsible manner. Our packaging is designed to be recycled and should be handled in accordance with your local recycling policies. Hardware Compliance The router meets the following hardware compliance requirements.
Appendix B: Installation Guidelines and Requirements Food and Drug Administration, Center for Devices and Radiological Health This equipment complies with 21 CFR 1040.10 and 1040.11 for the safe use of lasers. Canadian Department Of Communications Radio Interference Regulations This Class B (or Class A, if so indicated on the registration label) digital apparatus meets the requirements of the Canadian Interference-Causing Equipment Regulations.
ERX 11.1.x Hardware Guide pas que l'appareillage fonctionnera à la satisfaction de l'utilisateur. Avant d'installer l'appareillage, s'assurer qu'il peut être branché aux installations du service de télécommunications local. L'appareillage doit aussi être raccordé selon des méthodes acceptées. Le client doit toutefois prendre note qu'une telle installation n'assure pas un service parfait en tout temps.
Appendix B: Installation Guidelines and Requirements Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate. Notes explicatives du ministère des Communications: limites visant les accessoires L'étiquette du ministère des Communications du Canada indique que l'appareillage est certifié, c'est-à-dire qu'il respecte certaines exigences de sécurité...
Appendix C Cable Pinouts This appendix lists the cables and connector pinout assignments for the cables used with the ERX7xx models and ERX14xx models. It contains the following sections: SRP I/O Module on page 131 CT1 and CE1 I/O Modules on page 134 SRP I/O Module The SRP I/O module provides two management ports.
Page 148
ERX 11.1.x Hardware Guide Table 18: SRP I/O Module RS-232 Serial Connector Pinout Signal After you have configured an IP address on the system, you can connect using a host running Telnet over the 10/100Base-T Ethernet port on the SRP I/O module. The router ships with a straight-through cable having a male RJ-45 Ethernet connector on each end.
Page 149
Appendix C: Cable Pinouts Table 19: SRP I/O Module RJ-45 Connector Pinout Signal TX + TX – RX + no connect no connect RX – no connect no connect To facilitate connecting the system to a terminal, the system is shipped with one of each of the following cable adapters: DB-9 female to RJ-45 female crossover null modem adapter DB-9 female to RJ-45 female straight-through adapter...
ERX 11.1.x Hardware Guide Table 21: DB-9 RJ-45 Straight-Through Adapter Pinout DB-9 Pin RS-232 Signal Name RJ-45 Pin Ethernet Signal Name TX + TX – RX + no connect GND (signal) no connect RX – no connect no connect no connect none CT1 and CE1 I/O Modules CT1 I/O modules have 24 RJ-48C female connectors.
Page 151
Appendix C: Cable Pinouts Table 22: CT1/CE1 I/O Module RJ-48C Connector Pinout Signal RX Ring RX Tip no connect TX Ring TX Tip no connect no connect no connect For CE1 I/O modules with Telco connectors, the other ends of the cables are attached to a balun panel that splits the signals from two Telco connectors to 20 pairs of BNC connectors.
Page 152
ERX 11.1.x Hardware Guide Figure 58: Twenty-Port Balun Panel Table 23 on page 136 and Table 24 on page 137 list the pinouts for the Telco connectors on each cable. Table 23: Pinout of 50-Pin Telco Connector to Ports 0–9 Signal Signal Port 0 RX TIP...
Page 153
Appendix C: Cable Pinouts Table 23: Pinout of 50-Pin Telco Connector to Ports 0–9 (continued) Signal Signal no connect no connect no connect no connect no connect no connect Table 24: Pinout of 50-Pin Telco Connector to Ports 10–19 Signal Signal Port 10 RX TIP Port 10 RX RING...
Page 154
ERX 11.1.x Hardware Guide Table 24: Pinout of 50-Pin Telco Connector to Ports 10–19 (continued) Signal Signal no connect no connect no connect no connect no connect no connect no connect no connect CT1 and CE1 I/O Modules...
Appendix D Contacting Customer Support and Returning Hardware See the Juniper Networks Web site for complete customer service information: http://www.juniper.net/support/guidelines.html This appendix contains the following sections: Contacting Customer Support on page 139 Return Procedure on page 139 Locating Component Serial Numbers on page 140...
“Returning Products for Repair or Replacement” on page 142. Locating Component Serial Numbers Before contacting Juniper Networks to request a Return Materials Authorization (RMA), you must find the serial number on the chassis or component. To list all the...
Appendix D: Contacting Customer Support and Returning Hardware Figure 59: Representative Module Serial Number ID Label Information You Might Need to Supply to JTAC When requesting technical support from the JTAC by phone, be prepared to provide the following information: Priority level Indication of what activity was being performed on the router when the problem occurred...
Wire cutters Returning Products for Repair or Replacement In the event of a hardware failure, please contact Juniper Networks to obtain a Return Material Authorization (RMA) number. This number is necessary to ensure proper tracking and handling of returned material at the factory. Do not return any hardware until you have received an RMA.
Page 159
Appendix D: Contacting Customer Support and Returning Hardware Remove the chassis from the rack and bolt it to the shipping pallet. Cover the chassis with an ESD bag and place packing foam on top of and around the chassis. Place the crate cover over the chassis and fasten the cover to the pallet. Returning Products for Repair or Replacement...
Page 160
ERX 11.1.x Hardware Guide Returning Products for Repair or Replacement...
Appendix E Declaration of Conformity Declaration of Conformity on page 145 Declaration of Conformity Declaration of Conformity according to ISO/IEC Guide 22 and EN4514 Juniper Networks, Inc. Manufacturer’s Name: Juniper Networks, Inc. Manufacturer’s Address: 10 Technology Park Drive Westford, Massachusetts 01886 USA...
Page 162
ERX 11.1.x Hardware Guide Declaration of Conformity according to ISO/IEC Guide 22 and EN4514 Westford, MA, May 01, 2003 David H. Schilling Regulatory Affairs Declaration of Conformity...