Chorus Parameters - Roland Fantom XR Owner's Manual

Effects List

Chorus Parameters

The Fantom-XR's Chorus effect unit can also be used as a stereo
delay unit.
These settings allow you to select chorus or delay, and the
characteristics of the selected effect type.
Parameter Value
Chorus 0 (OFF),
Type 1 (CHORUS),
2 (DELAY),
3 (GM2 CHORUS)
Type: 1 (CHORUS)
Rate 0.05–10.00 Hz, note
Depth 0–127
Pre Delay 0.0–100.0 ms
Feedback 0–127
Filter Type OFF, LPF, HPF
Cutoff Freq 200–8000 Hz
Phase 0–180˚
Type: 2 (DELAY)
Delay Left 0–1000 ms, note
Delay Right
Delay Center
Center -98–+98 %
Feedback
HF Damp 200–8000 Hz,
BYPASS
Left Level 0–127
Right Level
Center Level
Type: 3 (GM2 CHORUS)
Pre-LPF 0–7
Level 0–127
Feedback 0–127
Delay 0–127
Rate 0–127
Depth 0–127
Send Level 0–127
To Reverb
If you specify the delay time as a note value, slowing down the
tempo will not change the delay time beyond a certain length.
This is because there is an upper limit for the delay time; if the
delay time is specified as a note value and you slow down the
tempo until this upper limit is reached, the delay time cannot
change any further. This upper limit is the maximum value that
can be specified when setting the delay time as a numerical
value.
216
Description
Selects either Chorus or Delay.
0 (OFF): Neither Chorus or Delay
is used.
1 (CHORUS): Chorus is used.
2 (DELAY): Delay is used.
3 (GM2 CHORUS): GM2 Chorus
is used.
Frequency of modulation
Depth of modulation
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Adjusts the amount of the chorus
sound that is fed back into the effect.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range
above the Cutoff Freq
HPF: cuts the frequency range
below the Cutoff Freq
Basic frequency of the filter
Spatial spread of the sound
Adjusts the delay time from the di-
rect sound until the delay sound is
heard.
Adjusts the proportion of the delay
sound that is fed back into the ef-
fect. Negative (-) settings will invert
the phase.
Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the
high frequencies, set this parameter
to BYPASS.
Volume of each delay sound
Cuts the high frequency range of
the sound coming into the chorus.
Higher values will cut more of
the high frequencies.
Volume of the chorus sound
Adjusts the amount of the chorus
sound that is fed back into the effect.
Adjusts the delay time from the di-
rect sound until the chorus sound is
heard.
Frequency of modulation
Depth of modulation
Adjusts the amount of chorus sound
that will be sent to the reverb.
note:
fig.MFX-note2.e
(Sixty-fourth-note triplet), (Sixty-fourth note),
(Thirty-second note), (Sixteenth-note triplet),
(Sixteenth note), (Eighth-note triplet),
(Eighth note), (Quarter-note triplet),
(Quarter note), (Half-note triplet),
(Whole-note triplet), (Dotted half note),
(Dotted whole note),
(Double-note triplet),
(Thirty-second-note triplet),
(Dotted thirty-second note),
(Dotted sixteenth note),
(Dotted eighth note),
(Dotted quarter note), (Half note),
(Whole note),
(Double note)