ZyXEL Communications USG FLEX H Series User Manual page 448

List of National Codes
COUNTRY
Austria
Belgium
Bulgaria
Croatia
Cyprus
Czech Republic
Denmark
Estonia
Finland
France
Germany
Greece
Hungary
Iceland
Ireland
Italy
Latvia
Safety Warnings
• Do not put the device in a place that is humid, dusty, has extreme temperatures, or that blocks the device ventilation slots. These conditions
may harm your device.
• Please refer to the device back label, datasheet, box specifications or catalog information for power rating of the device and operating
temperature.
• There is a remote risk of electric shock from lightning: (1) Do not use the device outside, and make sure all the connections are indoors. (2) Do
not install or service this device during a thunderstorm.
• Do not expose your device to dampness, dust or corrosive liquids.
• Do not store things on the device.
• Do not obstruct the device ventilation slots as insufficient airflow may harm your device. For example, do not place the device in an
enclosed space such as a box or on a very soft surface such as a bed or sofa.
• Do not install or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.
• Connect ONLY suitable accessories to the device.
• Do not open the device. Opening or removing the device covers can expose you to dangerous high voltage points or other risks.
• Only qualified service personnel should service or disassemble this device. Please contact your vendor for further information.
• Make sure to connect the cables to the correct ports.
• Place connected cables carefully so that no one will step on them or stumble over them.
• Disconnect all cables from this device before servicing or disassembling.
• Do not remove the plug and connect it to a power outlet by itself; always attach the plug to the power adaptor first before connecting it to
a power outlet.
• Do not allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor
or cord.
• Please use the provided or designated connection cables/power cables/ adaptors. Connect the power adaptor or cord to the right supply
voltage (for example, 120V AC in North America or 230V AC in Europe). If the power adaptor or cord is damaged, it might cause
electrocution. Remove the damaged power adaptor or cord from the device and the power source. Do not try to repair the power adaptor
or cord by yourself. Contact your local vendor to order a new one.
• CAUTION: There is a risk of explosion if you replace the device battery with an incorrect one. Dispose of used batteries according to the
instructions. Dispose them at the applicable collection point for the recycling of electrical and electronic devices. For detailed information
about recycling of this product, please contact your local city office, your household waste disposal service or the store where you
purchased the product.
• Do not leave a battery in an extremely high temperature environment or surroundings since it can result in an explosion or the leakage of
flammable liquid or gas.
• Do not subject a battery to extremely low air pressure since it may result in an explosion or the leakage of flammable liquid or gas.
• The following warning statements apply, where the disconnect device is not incorporated in the device or where the plug on the power
supply cord is intended to serve as the disconnect device.
- For a permanently connected device, a readily accessible method to disconnect the device shall be incorporated externally to the
device;
- For a pluggable device, the socket-outlet shall be installed near the device and shall be easily accessible.
• This device must be grounded by qualified service personnel. Never defeat the ground conductor or operate the device in the absence of a
suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that
suitable grounding is available. If your device has an earthing screw (frame ground), connect the screw to a ground terminal using an
appropriate AWG ground wire. Do this before you make other connections. If your device has no earthing screw, but has a 3-prong power
plug, make sure to connect the plug to a 3-hole earthed socket.
• When connecting or disconnecting power to hot-pluggable power supplies, if offered with your system, observe the following guidelines:
- Install the power supply before connecting the power cable to the power supply.
- Unplug the power cable before removing the power supply.
- If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from the power supply.
Appendix C Legal Information
ISO 3166 2 LETTER CODE COUNTRY
AT Liechtenstein
BE Lithuania
BG Luxembourg
HR Malta
CY Netherlands
CR Norway
DK Poland
EE Portugal
FI Romania
FR Serbia
DE Slovakia
GR Slovenia
HU Spain
IS Sweden
IE Switzerland
IT Turkey
LV United Kingdom
USG FLEX H Series User's Guide
448
ISO 3166 2 LETTER CODE
LI
LT
LU
MT
NL
NO
PL
PT
RO
RS
SK
SI
ES
SE
CH
TR
GB