Yamaha S90 ES Owner's Manual page 152

Yamaha music synthesizer owner's manual
Hide thumbs Also See for S90 ES:
Table of Contents

Advertisement

Performance Edit mode
[SF2] INS TYPE (Insertion Type)
InsEF Connect
(Insertion Effect Connection)
InsA Ctgry (Insertion A Category)
InsA Type (Insertion A Type)
InsB Ctgry (Insertion B Category)
InsB Type (Insertion B Type)
n
Insertion effects can be applied only to the A/D Part, among the Audio Input Parts.
[F6] EFFECT
This menu gives you comprehensive control over the effects. For details about the Effect connections in the Performance mode, see page 122.
[SF1] CONNECT (Connection)
[SF2] INS SW (Insertion Switch)
[SF3] PLG-EF (Plug-in Effect)
[SF4] REVERB
[SF5] CHORUS
Part Edit
These parameters are for editing the individual Parts that make up a Performance.
To switch between the display for Parts 1 - 4 to which the internal Voices are assigned and the display for Plug-in Parts (PLG1 - 3) to which
the Plug-in Voices are assigned, press the [F6] button.
n
When a Plug-in Voice is assigned to a Part of the selected Performance, some parameters may not be available depending on the installed Plug-in
board.
[F1] VOICE
[SF1] VOICE
PartSw (Part Switch)
Bank
Number
[SF2] MODE
Mono/Poly
ArpSwitch (Arpeggio Switch)
[SF3] LIMIT
NoteLimitH (Note Limit High)
NoteLimitL (Note Limit Low)
VelLimitH (Velocity Limit High)
VelLimitL (Velocity Limit Low)
152
Owner's Manual
Part Edit
This display is available only when the AD (A/D Part) is set to on from the [F6] EFFECT
The type and connection of the Insertion Effect applied to the A/D Part can be set from this display.
Same as in the CONNECT display in the Voice Edit mode ([VOICE]
[SF1] CONNECT). Please note that the InsEF Connect cannot be set to "parallel" here.
n
When selecting the effect types in this display, [SF3] INS A and [SF4] INS B are displayed and you can set the effect
parameters.
For details on the parameters, see page 122.
The Insertion Effects can be applied to up to eight Parts. This display lets you set to which Parts the Insertion
Effects are applied.
This display lets you set the Plug-in Insertion Effect related parameters when the Effect Plug-in Board PLG100-
VH has been installed to this synthesizer. For details on each parameter, refer to the Owner's Manual included
with the PLG100-VH.
The number of parameters and values available differs depending on the currently selected effect type. For
more information, see the Effect Type List in the separate Data List booklet.
[PERFORM]
Performance selection
Determines whether each Part is on or off. Since a Performance can consist of up to four Parts, you can select
four Parts from Parts 1 - 4 and the Plug-in Parts 1 - 3.
Settings: on, off
Determines the Voice Bank (page 30) for each Part.
For details about the Plug-in Voice Bank, refer to the Owner's Manual included with your Plug-in Board.
Determines the Voice Program number for each Part.
For details about the Plug-in Voice Program number, refer to the Owner's Manual included with your Plug-in
Board.
Determines the playback method of the Voice for each Part — monophonic (single notes only) or polyphonic
(multiple notes).
Settings: mono, poly
n
This parameter is not available for the Part to which a Drum Voice is assigned.
Determines whether Arpeggio is on or off for the currently selected Part.
Settings: on, off
Determines the lowest and highest notes of the keyboard range for each Part. Each Part will only sound for
notes played within its specified range.
Settings: C -2~G8
n
If you specify the highest note first and the lowest note second, for example "C5 to C4," then the note range covered will
be "C-2 to C4" and "C5 to G8."
n
You can set the note by pressing the keyboard while holding the [INFORMATION] button.
Determines the minimum and maximum values of the velocity range within which each Part will respond. Each
Part will only sound for notes played within its specified velocity range.
Settings: 1~127
n
If you specify the maximum value first and the minimum value second, for example "93 to 34," then the velocity range
covered will be "1 to 34" and "93 to 127."
[EDIT]
[COMMON]
[EDIT]
Part selection
[SF2] INS SW display.
[F6] EFFECT

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents