Xerox WorkCentre Pro 423 Service Manual page 225

Chain Function Item
57 601** G3M0 TX Modem Speed
57 602** G3M0 TX Modem Speed
57 603 14400 bps modem type
57 610** EQM Comparative data (G3M0) in
4800BPS
57 611** EQM Comparative data (G3M0) in
7200BPS
57 612** EQM Comparative data (G3M0) in
9600BPS
57 613** EQM Comparative data (G3M0) in
TCM7200BPS
57 614** EQM Comparative data
TCM9600BPS
57 615** EQM Comparative data
12000BP
57 616** EQM Comparative data
14400BPS
57 620 Communication Declaration Data Type
57 623 CCITT MMR capability
57 624 TCM capability
WorkCentre Pro 423/428
Content
1:2400bps 2:4800bps
3:7200bps 4:9600bps
5:12000bps 6:14400bps
7:16800bps 8:19200bps
9:21600bps 10:24000bps
11:26400bps 12:28800bps
13:31200bps 14:33600bps
1:2400bps 2:4800bps
3:7200bps 4:9600bps
5:12000bps 6:14400bps
7:16800bps 8:19200bps
9:21600bps 10:24000bps
11:26400bps 12:28800bps
13:31200bps 14:33600bps
0=Off 1=V1.7 2=V3.3 & V1.7
3=V3.3
0 to 7F FTT send
0 to 7F FTT send
0 to 7F FTT send
0 to 7F FTT send
(G3M0) in 0 to 7F FTT send
(G3M0) in 0 to 7F FTT send
(G3M0) in 0 to 7F FTT send
Total value of
MH=2, MR=4, MMR=8, IMAGE=16,
JBIG=32, Binary=256
0:Off 1:On
0:Off 1:On
Default
14 Sets up a starting Modem speed for sending G3 signals.
Individually reflectable on each speed dial (refer to page 2-207)
14 Sets up a starting Modem speed for receiving G3 signals. The loading Modem
based on the modem speed setup will be informed to the NSF/DIS signal.
02 Selects a 14400bps modem type for sending and receiving G3 signals. The
ITU-T recommends to use V.17 and this data needs not be changed.
47(2F) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving 4800bps
48(30) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving 7200bps
56(38) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving 9600bps
70(46) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving TCM7200bps
64(40) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving TCM9600bpS
64(40) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving 12000bps
64(40) Determines the standard fall back data based on the EQM(Eye Quality
Monitor) at receiving 14400bps
318 Selects the coded or composite capability to inform the remote terminal when
sending NSF/DIS signals. The data should not be changed unless otherwise
instructed.
01 Selects handling of the MMR capability that can be instructed by ITU-T. The
data should not be changed unless otherwise instructed.
01 Selects whether or not to enable the TCM capability. The data should not be
changed unless otherwise instructed.
03/02
2-193
Description
How to use the Diagnostic C/E Mode
CHAPTER 2 TROUBLESHOOTING
Access
by
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE