Xerox WorkCentre Pro 423 Service Manual page 221

Chain Function Item
57 273 CED Send time
57 274 Interval between the line closure and the
CED signal transmission (Fax only
mode)
57 276 CED signal transmission timing by
manual receive
57 301 First subscriber to be displayed
57 302 Communication capability of the first
subscriber's number (Telephone)
57 303 Communication capability of the first
subscriber's number (G2/G3 Fax)
57 304 Communication capability of the first
subscriber's number(G4 Fax)
57 311 Second subscriber's number to be
displayed
57 312 Communication capability of the second
subscriber's number (Telephone)
57 313 Communication capability of the second
subscriber's number (G2/G3 Fax)
57 314 Communication capability of the second
subscriber's number (G4 Fax)
57 321 Third subscriber's number to be
displayed
57 322 Communication capability of the third
subscriber's number (Telephone)
57 323 Communication capability of the third
subscriber's number (G2/G3 Fax)
WorkCentre Pro 423/428
Content Default
0 to 25500ms (1step=100ms) 27
0 to 25500ms (1step=100ms) 18
0 to 25500ms (1step=100ms) 00
0:Not to be displayed 1:To be 00
displayed
0:Off 1:On 00
0:Off 1:On 00
0:Off 1:On 00
0:Not to be displayed 1:To be 00
displayed
0:Off 1:On 00
0:Off 1:On 00
0:Off 1:On 00
0:Not to be displayed 1:To be 00
displayed
0:Off 1:On 00
0:Off 1:On 00
03/02
2-189
Description
This data changes the frequency of a CED signal. As the send time has been
specified (2.6 to 4.0 sec.) as standard by the ITU-T recommendation and
some transmitters monitor the detection time of CED signals, be careful when
changing.
This data specifies the time from when a call terminates until when the
terminal is switched to FAX and a CED signal is sent. If the CED signal is sent
at a late timing, the transmitter may not recognize the terminal as a fax. If the
CED signal is sent at an early timing, a connection delay may disable the
transmitter to detect the CED signal.
Specifies time between the pressing of manual receive button and the
transmission of CED signal. As described in Chain=057 and
Function=274(Time between the line close and the CED signal transmission)
for auto receive, when the CED signal is sent at a late timing, the transmitter
may not recognize the terminal as a Fax.
Specifies whether or not to enable "26 Informing the sending terminal's
number" when the telephone number has been in->23. ISDN ID 1".
Specifies whether or not to have "25 Communication Capability" functioned as
a telephone when the telephone number has been stored in ISDN ID 1".
Specifies whether or not to have the G2/G3FAX functioned as "25
Communication Capability" when the telephone number has been stored in.
ISDN ID 1".
Specifies whether or not to have the G4 FAX functioned as "25
Communication Capability" when the telephone number has been stored in
ISDN ID 1".
Specifies whether or not to enable "30. Informing the sending terminal's
number" when the telephone number has been stored in ISDN ID 2".
Specifies whether or not to have "29. Communication Capability" functioned as
a telephone when the telephone number has been stored in ISDN ID 2".
Specifies whether or not to have the G2/G3FAX functioned as "29.
Communication Capability" when the telephone number has been stored in
ISDN ID 2".
Specifies whether or not to have the G4 FAX functioned as "29.
Communication Capability" when the telephone number has been in ISDN ID
2".
Specifies whether or not to enable "34. Informing the sending terminal's
number" when the telephone number has been stored in ISDN ID 3".
Specifies whether or not to have "33. Communication Capability" functioned as
a telephone when the telephone number has been stored in ISDN ID 3".
Specifies whether or not to have the G2/G3FAX functioned as "33.
Communication Capability" when the telephone number has been stored in
ISDN ID 3".
How to use the Diagnostic C/E Mode
CHAPTER 2 TROUBLESHOOTING
Access
by
CE
CE
CE
User
User
User
User
User
User
User
User
User
User
User