Xerox WorkCentre Pro 423 Service Manual page 220

WorkCentre Pro 423/428
Chain Function Item
57 162 Restrictions on sending ISDN_ANALOG
57 163*** Restrictions on sending G4CH0(Channel
0 communication guard)
57 164 Restrictions on sending
ISDN_CSDN0:G4 restriction
(B1ch)(network guard)
57 165 Restrictions on sending
ISDN_CSDN1:G4 restriction
(B2ch)(network guard)
57 180 ISDN dial tone
57 184 DTMF Signal Amplification Gain
57 190 Closed-Area Communication
57 201 Reception Mode
57 202 Ring detection time at FAX
57 203 Restriction of change of the ring
detection time by user
57 204
57 210 Direct Mail refection
57 260 CNG Signal (Dial Tone) Detection Time.
57 270 CED Send
57 271 CED Send for Manual Reception
57 272 CED Send Frequency
2-188
03/02
Content Default
0: Send not restricted 1:Send 00
restricted
0: Send not restricted 1:Send 00
restricted
0: Send not restricted 1:Send 00
restricted
0: Send not restricted 1:Send 00
restricted
0:tone off 1:400Hz consecutive tone 01
2:400Hz On(260ms)/Off(260ms)
3:400Hz On(180ms)/Off(260ms)
0 to -28 dB m 16=-16
dB m
0:Disable 1:Enable 00
0: TEL/FAX mode (TEL Priority) 01
1: FAX mode (FAX Only)
0 to 255 sec. (1step=1 sec.) 00
0: Do not restrict 1: Restrict 00
0 to 255 sec. 1step=1 sec. 21
0=Off 1=On 00
0 to 25500(ms) 1step=100ms 55
0: Do not send 1: Send 01
0: Do not send 1: Send 01
0:2100Hz 1:1650Hz 2:1100Hz 00
CHAPTER 2 TROUBLESHOOTING
How to use the Diagnostic C/E Mode
Description
The data can be changed when analog send (G3 Fax/Telephone) by the ISDN
line needs to be restricted. By changing the data, the ISDN line can be open
only to be used for digital send or digital send or analog receive.
The data can be changed when G4 mode send by the ISDN line needs to be
restricted. By changing the data, the ISDN line can be restricted only to be
used for analog send operation.
The data can be changed when G4 mode send to the ISDN line via B1ch
needs to be restricted. By changing the data, the traffic volume of G4 send
operation via ISDN line can be restricted.
The data can be changed when G4 mode send to the ISDN line via B2ch
needs to be restricted. By changing the data, the traffic volume of G4 send
operation via ISDN line can be restricted.
The data specifies the mock dial tone type to be informed to the operator by
Main unit when the handset is lifted up and the ISDN line has been captured.
This data specifies a send power level for a selected pushbutton tone signal
(DTMF) when an ISDN line is connected.
Set the Reception Mode
Set up time to switch to Fax when transmission is received. Bell rings at the
handset/separate telephone for the specified time when the terminal receieves
a call.
The data to restrict the change of 57-202 ring detection time at FAX.
Auto Answering Time in TEL/FAX Auto Switching Mode (TEL Priority)
The terminal refers the last 4 digits of all numbers stored in the speed dial
directory to the last 4 digits of the ID codes sent from the remote terminal and
receives only the numbers that match. The feature can be switched on and
off. "Space" will be ignored when the reference is made.
This data is used in TEL Priority mode. If no CNG signal is detected within this
time, the auto answering function (external telephone) is called.
This data changes the frequency of a CED. If an eco suppressor causes a
fault in international communication, change the frequency to other than 2100
Hz. However, be careful when changing the frequency because some
transmitters may monitor only CED signals of 2100 Hz
Access
by
CE
CE
CE
CE
CE
CE
User
CE
CE