Trane TR150 Programming Manual page 32

Parameters
Parameter 1-10 Motor
Construction Asynchron
Parameter 2-01 DC Brake
Current
Parameter 2-02 DC Braking
Time
Parameter 2-04 DC Brake
Cut In Speed [Hz]
Parameter 2-06 Parking
Current
Parameter 2-07 Parking
Time
Parameter 2-10 Brake
Function
Parameter 2-16 AC brake
Max. Current
Parameter 2-17 Over-voltage
Control
Parameter 4-10 Motor Speed
Direction
Parameter 4-14 Motor Speed
High Limit [Hz]
Parameter 4-18 Current
Limit
Parameter 4-19 Max Output
Frequency
Parameter 4-58 Missing
Motor Phase Function
Parameter 14-01 Switching
Frequency
Parameter 14-03 Overmodu-
lation
Parameter 14-07 Dead Time
Compensation Level
Parameter 14-08 Damping
Gain Factor
Parameter 14-09 Dead Time
Bias Current Level
Parameter 14-10 Mains
Failure
Parameter 14-11 Mains
Voltage at Mains Fault
Parameter 14-12 Function at
Mains Imbalance
Parameter 14-27 Action At
Inverter Fault
Parameter 14-40 VT Level
Parameter 14-41 AEO
Minimum Magnetisation
Parameter 14-44 d-axis
current optimization for IPM
BAS-SVP16B-EN
Programming Guide
[2]
[3]
[1] PM PM,
PM,
[0] Motor salient
salient
non IPM,
IPM,
salient non-
Sat
Sat
x x x x
x x x x
x x x x
x x x
x x x
x x x x
x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x
02/2017 All rights reserved.
Parameter 1-10 Motor
Construction Asynchron
Parameter 14-50 RFI Filter
Parameter 14-51 DC-Link
Voltage Compensation
Parameter 14-55 Output
Filter
Parameter 14-64 Dead Time
Compensation Zero Current
Level
Parameter 14-65 Speed
Derate Dead Time Compen-
sation
Parameter 30-22 Locked
Rotor Detection
Parameter 30-23 Locked
Rotor Detection Time [s]
Table 3.2 Active Parameters
1-10 Motor Construction
Option: Function:
[0] Asynchron For asynchronous motors.
*
[1] PM, non- For permanent magnet (PM) motors with
salient SPM surface-mounted (non-salient) magnets.
Refer to parameter 1-14 Damping Gain to
parameter 1-17 Voltage filter time const. for
details about optimizing the motor
operation.
[2] PM, salient For permanent magnet (PM) motors with
IPM, non Sat. interior (salient) magnets, without
inductance saturation control.
[3] PM, salient For permanent magnet (PM) motors with
IPM, Sat. interior (salient) magnets, with inductance
saturation control.
3.2.3 1-14 to 1-17 VVC
The default control parameters for VVC
core are optimized for applications and inertia load in the
range of 50>Jl/Jm>5. Jl is load inertia from the application
and Jm is machine inertia.
For low inertia applications (Jl/Jm<5), it is recommended
that parameter 1-17 Voltage filter time const. is increased
with a factor of 5–10. Sometimes,
parameter 14-08 Damping Gain Factor should also be
reduced to improve performance and stability.
For high-inertia applications (Jl/Jm>50), increase
parameter 1-15 Low Speed Filter Time Const. and
parameter 1-16 High Speed Filter Time Const. to improve
performance and stability.
[2]
[3]
[1] PM PM,
PM,
[0] Motor salient
salient
non IPM,
IPM,
salient non-
Sat
Sat
x
x x x x
x x x x
x x x x
x x x x
x x x
x x x
+
PM
+
PM motor control
31
3 3