Trane TR150 Programming Manual page 31

Parameters
3.2.2 1-10 to 1-13 Motor Selection
NOTICE
This parameter group cannot be adjusted while the
motor is running.
3 3
The following parameters are active ('x') depending on the
setting of parameter 1-10 Motor Construction.
Parameter 1-10 Motor
Construction
Parameter 1-00 Configu-
ration Mode
Parameter 1-03 Torque
Characteristics
Parameter 1-06 Clockwise
Direction
Parameter 1-08 Motor
Control Bandwidth
Parameter 1-14 Damping
Gain
Parameter 1-15 Low Speed
Filter Time Const.
Parameter 1-16 High Speed
Filter Time Const.
Parameter 1-17 Voltage filter
time const.
Parameter 1-20 Motor Power
[kW]
Parameter 1-22 Motor
Voltage
Parameter 1-23 Motor
Frequency
Parameter 1-24 Motor
Current
Parameter 1-25 Motor
Nominal Speed
Parameter 1-26 Motor Cont.
Rated Torque
Parameter 1-29 Automatic
Motor Adaption (AMA)
Parameter 1-30 Stator
Resistance (Rs)
Parameter 1-33 Stator
Leakage Reactance (X1)
Parameter 1-35 Main
Reactance (Xh)
Parameter 1-37 d-axis
Inductance (Ld)
Parameter 1-38 q-axis
Inductance (Lq)
30
TR150 and TR170
[2]
[3]
[1] PM PM,
PM,
[0] Motor salient
salient
Asynchron non IPM,
IPM,
salient non-
Sat
Sat
x x x x
x
x x x x
x x x x
x x x
x x x
x x x
x x x
x
x
x
x x x x
x x x x
x x x
x x x x
x x x x
x
x
x x x
x x
02/2017 All rights reserved.
Parameter 1-10 Motor
Construction Asynchron
Parameter 1-39 Motor Poles
Parameter 1-40 Back EMF at
1000 RPM
Parameter 1-42 Motor Cable
Length
Parameter 1-43 Motor Cable
Length Feet
Parameter 1-44 d-axis
Inductance Sat. (LdSat)
Parameter 1-45 q-axis
Inductance Sat. (LqSat)
Parameter 1-46 Position
Detection Gain
Parameter 1-48 Current at
Min Inductance for d-axis
Parameter 1-49 Current at
Min Inductance for q-axis
Parameter 1-50 Motor
Magnetisation at Zero Speed
Parameter 1-52 Min Speed
Normal Magnetising [Hz]
Parameter 1-55 U/f Charac-
teristic - U
Parameter 1-56 U/f Charac-
teristic - F
Parameter 1-62 Slip
Compensation
Parameter 1-63 Slip
Compensation Time
Constant
Parameter 1-64 Resonance
Dampening
Parameter 1-65 Resonance
Dampening Time Constant
Parameter 1-66 Min. Current
at Low Speed
Parameter 1-70 PM Start
Mode
Parameter 1-71 Start Delay
parameter 1-72 Start
Function
Parameter 1-73 Flying Start
Parameter 1-80 Function at
Stop
Parameter 1-90 Motor
Thermal Protection
parameter 2-00 DC Hold
Current
[2]
[3]
[1] PM PM,
PM,
[0] Motor salient
salient
non IPM,
IPM,
salient non-
Sat
Sat
x x x x
x x x
x x x x
x x x x
x
x
x x x
x
x
x
x
x
x
x
x
x
x
x x x
x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
BAS-SVP16B-EN