Cisco Catalyst 3550 Command Reference Manual page 525

Chapter 2 Cisco IOS Commands
• name vlan-name: names the VLAN with an ASCII string from 1 to 32 characters that must be unique
within the administrative domain. The default is VLANxxxx where xxxx represents four numeric
digits (including leading zeros) equal to the VLAN ID number.
no: negates a command or returns it to the default setting.
•
• parent parent-vlan-id: specifies the parent VLAN of an existing FDDI, Token Ring, or TrCRF
VLAN. This parameter identifies the TrBRF to which a TrCRF belongs and is required when
defining a TrCRF. Valid values are from 0 to 1005. The default parent VLAN ID is 0 (no parent
VLAN) for FDDI and Token Ring VLANs. For both Token Ring and TrCRF VLANs, the parent
VLAN ID must already exist in the database and be associated with a Token Ring-NET or TrBRF
VLAN.
Though visible in the command-line interface, the private-vlan command is not supported.
Note
remote-span: adds the Remote SPAN (RSPAN) feature to the VLAN. When the RSPAN feature is
•
added to an existing VLAN, the VLAN is first deleted and is then recreated with the RSPAN feature.
Any access ports are deactivated until the RSPAN feature is removed. The new RSPAN VLAN is
propagated by VTP for VLAN-IDs that are lower than 1024. Learning is disabled on the VLAN.
Only Layer 2 switch protocols will be processed by the CPU. Broadcast packets, multicast packets
and unicast packets addressed directly to the switch will be flooded on the VLAN but will not be
forwarded to the CPU.
ring ring-number: defines the logical ring for an FDDI, Token Ring, or TrCRF VLAN. Valid values
•
are from 1 to 4095. The default for Token Ring VLANs is 0. For FDDI VLANs, there is no default.
said said-value: specifies the security association identifier (SAID) as documented in IEEE 802.10.
•
The value is an integer from 1 to 4294967294 that must be unique within the administrative domain.
The default value is 100000 plus the VLAN ID number.
shutdown: shuts down VLAN switching on the VLAN. This command takes effect immediately.
•
Other commands take effect when you exit config-vlan mode.
state: specifies the VLAN state:
•
–
–
ste ste-number: defines the maximum number of spanning-tree explorer (STE) hops. This keyword
•
applies only to TrCRF VLANs. Valid values are from 0 to 13. The default is 7.
• stp type: defines the spanning-tree type for FDDI-NET, Token Ring-NET, or TrBRF VLANs. For
FDDI-NET VLANs, the default STP type is ieee. For Token Ring-NET VLANs, the default STP
type is ibm. For FDDI and Token Ring VLANs, the default is no type specified.
–
–
–
tb-vlan1 tb-vlan1-id and tb-vlan2 tb-vlan2-id: specifies the first and second VLAN to which this
•
VLAN is translationally bridged. Translational VLANs translate FDDI or Token Ring to Ethernet,
for example. Valid values are from 0 to 1005. If no value is specified, 0 (no transitional bridging) is
assumed.
78-11195-09
active means the VLAN is operational (the default).
suspend means the VLAN is suspended. Suspended VLANs do not pass packets.
ieee for IEEE Ethernet STP running source-route transparent (SRT) bridging.
ibm for IBM STP running source-route bridging (SRB).
auto for STP running a combination of source-route transparent bridging (IEEE) and
source-route bridging (IBM).
Catalyst 3550 Multilayer Switch Command Reference
vlan (global configuration)
2-499