Table of Contents
Advertisement
need to do so several times until the service confirms that data can be sent or received.
•
The first parameter of the
parameter is the number of bytes which the host either wants to send to or is able to receive from the module.
The way the module handles the data transfer follows the rules of the ordinary socket interface and is aware
that a host may be limited by its input buffer size. The maximum data size supported by MC55 is 1500 bytes
in both directions (read or write). To send or receive more than 1500 bytes, the read or write action shall be
repeated until the data transfer has completed. Each read or write action requires that the command response
(of
or AT^SISW) confirms that the service is ready to send or receive data.
AT^SISR
To end an upload data stream set the
•
The
command shall be used to monitor the progress of the session. The command reports the ser-
AT^SISI
vice state of the used service profile and indicates the number of bytes received, the number of bytes sent
and, in the case of sending, the number of bytes acknowledged or unacknowledged at TCP layer.
•
If an error occurs during a session you can enter the
tify the reason. This is especially important in polling mode.
•
The
command can be used any time to query the current status of one or all connection profile(s).
AT^SICI
•
Finally, to end a session, enter the
Maximum number of profiles defined / used:
•
Up to 6 connection profiles can be created (with AT^SICS).
•
Up to 10 service profiles can be created (with AT^SISS), but the number of parallel profiles of the same ser-
vice type is limited as listed below. If the maximum number of a service profile type is already defined, any
attempt to set up another profile for the same type will be denied with "+CME ERROR: operation of service
temporary not allowed".
-
Maximum 3 HTTP profiles
-
Maximum 6 socket profiles: The socket service can accept an incoming connection only when at least one
service profile is still free (not yet created with AT^SISS), otherwise the incoming connection will be
rejected from the listener.
-
1 FTP profile
-
1 POP3 profile
-
1 SMTP profile
•
The TCP/IP stack of MC55 supports one service profile at a time. Trying to run more than one service profile
may result in a blocking of one of these service profiles.
Using Internet Service AT commands on several interfaces (ASC0, ASC1 or Multiplex mode on ASC0):
•
A connection profile can be created on one interface and then viewed or changed on all other interfaces.
•
A service profile can be used only on one interface at a time:
-
Service profiles can only be opened on the interface where they have been defined with AT^SISS.
-
Accordingly, on each interface the read commands AT^SISO? and AT^SISI? deliver full status informa-
tion for the service profiles configured / opened on this interface, while service profiles related to other
interfaces are only listed by
Type") without any status parameters.
-
Changes to a service profile are allowed only on the same interface where it was created, trying to change
it on another interface is denied with "+CME ERROR: Invalid index". If queried with the read command
AT^SISS? the entire profile is returned on the interface where the service profile was created, while on all
other interfaces only the service type of the profile is stated.
-
To free a service profile for use on another interface, use the
= "none". This action deletes the entire profile and restores all parameters of the profile to their initial
power-up state (all values are empty). For example, to remove the service profile 3, set AT^SISS=3,srv-
Type,none. After this, a new profile 3 can be created on any other interface.
MC55_ATC_V04.00
Confidential / Released
or
commands is always the <srvProfileId>, the second
AT^SISR
AT^SISW
<eodFlag>
write command and the <srvProfileId>.
AT^SISC
<srvProfileId>
Page 220 of 475
in the last
command.
AT^SISW
command and the
AT^SISE
and service type name (=
command and select service type
AT^SISS
to iden-
<srvProfileId>
value "srv-
<srvParmTag>
3/17/06
Advertisement
Table of Contents
