Table of Contents
Advertisement
"PS"
"P2"
Factory defined SIM locks:
Typical examples of factory set SIM locks are prepaid phones or network locks, used to restrict the operation of
a mobile to a specific provider or operator. The client should be aware that each of these lock types can only be
unlocked if the associated password is available. For example, a mobile can be locked to accept only SIM cards
from the respective provider, or even one single SIM card. Once a different SIM card is inserted the ME will
prompt the client to enter a specific code. This is not the PUK of the SIM card, but usually an 8-digit code which
needs to be requested from the provider.
The locks can only be set by the manufacturer and need to be agreed upon between the parties concerned, e.g.
provider, operator, distributor etc. on the one side and the manufacturer on the other side. For details contact
your local dealer or Siemens AG.
"PF"
"PN"
"PU"
"PP"
"PC"
Supplementary Service Call Barring:
Supplementary Service "Call Barring" allows to specify conditions under which calls will be disallowed by the
network.
The availability of the Supplementary Services varies with the network. To benefit from call barring the client will
need to subscribe them, though a limited number of call barring types may be included in the basic tariff pack-
age.
length>: The Network Password needs to be supplied from the network provider or network oper-
<password
ator. Usually there is one 4 digit password which applies to all call barring options. For details contact your pro-
vider.
"AO"
"OI"
"OX"
"AI"
MC55_ATC_V04.00
Confidential / Released
Phone locked to SIM card. ME requests password when other than current SIM
card is inserted.
"PS" lock is frequently referred to as "phone lock", or "device lock". Accord-
ingly, the password may be called "phone code" or "device code". The "PS"
password is not associated with the PUK of the SIM card. It must be defined
before the first use of
<facility>
length>: 4 digits.
<password
If incorrectly entered three times, the Master Phone Code is required to lift the
lock. This Unblocking procedure is performed with
ing parameters: <facility>="PS",
(to be obtained from the module manufacturer), and
new phone code ("PS" password for lock facility), if desired.
Mind that successful PIN authentication is a prerequisite for use of AT com-
mand AT+CPWD. If Pin authentication has not been completed, input of the
Master Phone code password is possible only with AT command
ATD. For further detail please refer to Section 5.1.1,
word authentication
fails?.
Once the Master Phone Code has been acctepted, the mobile is operational,
and the "PS" lock is no longer active. If needed it must be set once again with
AT+CLCK.
SIM PIN 2, e.g. required for authentication with facility lock "FD" (cf. AT+CLCK).
If incorrectly entered three times, the SIM PUK 2 is required to perform authen-
tication. Input of the SIM PUK 2 password is possible only with AT command
or ATD. For further detail please refer to Section 5.1.1,
AT+CPIN2
if PIN or password authentication
length>: 4 to 8 digits.
<password
Lock Phone to the very First SIM card
Network Personalisation
Network subset Personalisation
Service Provider Personalisation
Corporate Personalisation
BAOC (Bar All Outgoing Calls)
BOIC (Bar Outgoing International Calls)
BOIC-exHC (Bar Outgoing International Calls except to Home Country)
BAIC (Bar All Incoming Calls)
Page 116 of 475
"PS" with AT+CLCK.
AT+CPWD
password>= Master Phone Code
<old
<new
What to do if PIN or pass-
fails?.
using the follow-
password>= the
or
AT+CPIN
What to do
3/17/06
Advertisement
Table of Contents
