Functions And Operations - Vermont Castings SDDVTCBSB Installation & Operating Manual

Setting Privacy Code on Transmitter (Figure 63)
The remote transmitter privacy code is preset in factory. In
the event of activation or interference from other nearby
transmissions, change the code using the following
procedures (learn function must be performed after changing
the code):
• Press the ON/arrow button and the
TIMER button at the same time to
enter privacy code setup mode.
• The setup display is shown in the
figure. The four digits on the top
stand for the privacy code (as the
actual DIP switches on Ambient's
previous remotes). The default
values of the four digits will be all
"1" (ON).
• The first digit will be flashing upon
entering the setup mode. Push
the ON button to toggle its value
between "0" (OFF) and "1"(ON), and push the "OFF"
button to jump to the next digit. The next digit will then
start flashing and the first one stops flashing. Set up the
four digits to your choice.
• After setting up all the four digits, push "OFF" to finish the
process and return to the previous mode.
• The Signature Command control board then needs to
re-learn the new setting.
Performing Learn Function
• The RF receiver button on the control board in the stove
must be in the ON position before the learn function can
begin. With the Command Center master switch in the ON
position, use paper clip to depress the recessed button on
Control Board, one beep for RF receiver ON or two beeps
for RF receiver OFF. Figure 64
• Holding the OFF button on the Command Center while
turning on the master switch will activate the learn function
for the transmitter. Figure 64
• After the above operation, two beeps will be given and
the green LED on the Command Center will flash for 10
seconds.
• During the 10 seconds, press the OFF button on the
transmitter to learn. Another two beeps will be given to
confirm a successful learning. Figure 65
Resetting the Transmitter
If the transmitter is not working properly, reinstall the batteries
to reset the transmitter.
• Pull out at least one of the batteries.
• Press any key on the screen to discharge.
• Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds until
the display refreshes will also reset the transmitter.
40
Figure 63
FP2649
set privace code
Vermont Castings • Stardance SDDVTSB Installation Manual_R10 • 04/18
LED
OFF
Battery Door
RF Receiver
ON/OFF
CONTROL
BOARD
Figure 64 - Command center and control board
!
Do not use two (2) or more remote control systems
in the same area with the same privacy code setting,
as they will communicate with each other. This may
cause the appliances to malfunction.

Functions and Operations

General
The TSFSC Remote Control has four (4) operating modes:
Manual, Timer, Thermostatic and Smart Mode® thermostat.
The control system can be set to temperature range between
45° F and 90° F. The blower speed and flame height can be
adjusted in the manual, timer and thermostatic mode. The
Smart Mode® thermostat will automatically adjust flame
height and blower speed according to the difference between
Set and Room temperatures.
The transmitter will operate the remote receiver from 1 foot
to a maximum of 30 feet. The distance is reduced when
batteries are low.
Manual Mode (Figure 65)
In this mode, the TIMER button and the THERMO button will
only display "TIMER" and "THERMO", respectively without
showing the time and the SET temperature. Pressing the
ON/up and OFF/down buttons will change the flame height
if none of the menu buttons (TIMER, THERMO, LIGHT, FAN,
AUX) are pressed and flashing.
• Press the ON/up button to turn on the stove. The flame
icon on the LCD displays High.
ON
Master Switch
Front Panel
Bezel Optional
FP1917
Signature components
FP2650
WARNING
8/08
command ctr ctrl brd
3-90-20306760