Vermont Castings SDDVTCBSB Installation & Operating Manual page 41

• Press the OFF/down button to
decrease the flame height and
turn off the stove. When the OFF/
down button is pressed for three
times, the flame icon changes
form High to Medium, to Low,
then to Off.
• If the OFF button is held for more
than 3 seconds at any flame
height, the stove will be turned off
and the flame icon disappears.
• Sliding up and down on the arrow
buttons can also turn on or turn
off the stove.
• If the stove is shut off using the above methods in 3
and 4, all the settings will be remembered and will be
resumed next time the stove is turned on (Memory Off).
Timer Mode (Figure 66)
Press the TIMER button to enter timer mode. The stove will
stay on for a period of time as specified by the timer and
then be shut off by the transmitter when the timer counts
down to zero.
• When the TIMER button is pressed, the Set Time
appears in the frame of the button
and flashes.
• Use ON/up and OFF/down to
increase or decrease the Set
Time in 15 min. increments,
between 0:00 to 6:00. Sliding up
and down on the arrow buttons
will increase or decrease the Set
Time in 1 hour increments.
• Push the TIMER button again
to confirm the Set Time, the
transmitter sends an ON signal to
turn on the stove.
• The flashing stops and the ON/up
and OFF/down buttons become flame height controller
again. The flame height will then stay as set up by the
ON/up and OFF/down buttons.
• The TIMER button can be used when the transmitter is
in Manual Mode or in Thermostat Mode. In both modes,
the stove will be shut down completely when the timer
counts down to zero.
To exit Timer Mode, you can do one of the following:
• Push and hold the TIMER button for 3 seconds
• Use the OFF/down buttons to decrease the Set Time to
zero.
• Slide down on the arrow buttons to exit TIMER mode
and shut off the stove.
41
Figure 65
FP2651
Manual mode
Figure 66
FP2652
Timer mode
Vermont Castings • Stardance SDDVTSB Installation Manual_R10 • 04/18
Thermostat Mode (Figure 67)
NOTE: The Command Center buttons will disable when
thermostat is being used.
Press the THERMO button to set the
transmitter in thermostat mode. The
transmitter will automatically turn on
the stove when the room temperature
is below the set temperature and
turn off the appliance when the
room temperature is above the set
temperature within one degree.
1. When the THERMO button is
pressed, the Set temperature
appears in the frame of the button
and flashes.
2. Use ON/up and
to increase or decrease the
Set temperature in 1 degree
increments, between 45 degrees and 90 degrees.
Slide up and down on the arrow buttons will increase or
decrease the Set Temperature in 10 degrees increments.
3. Press the THERMO button again to confirm the Set
Temperature. The transmitter will send out an On signal
or an Off signal depending on the relationship between
the Set temperature and the Room temperature.
4. The flashing stops and the ON/up and OFF/down buttons
become flame height controller again. The flame height
will then stay as set up by the ON/up and OFF/down
buttons.
5. To exit Thermostat Mode:
a. push and hold the THERMO buttons for 3 seconds
b. slide down on the arrow buttons to exit Thermostat
mode and shut off the stove.
Smart Mode Thermostat Option for Thermostat Mode
®
(Figure 68)
Press and hold the THERMO
button and the ON/UP button
at the same time for 3 seconds
to toggle between Smart Mode
thermostat and the regular
Thermostat Mode. The icon
"Smart Mode" will appear under
the Set Temperature.
transmitter will automatically
adjust the flame height
according to the difference
between the set temperature
and the room temperature.
There is no manual flame height
adjustment. The fan speed will
also automatically adjust if turned on.
OFF/down
Figure 67
FP2653
thermo mode
or
®
The
Figure 68
FP2654
smart mode
3-90-20306760
Smart
Mode
Icon