Sharp MX-2630N User Manual page 7

BEFORE USING THE MACHINE►BEFORE USING THE MACHINE
(19) (20)
(12) Saddle Stitch Finisher (large stacker)
This staples and folds paper. A punch module can also
be installed to punch holes in output paper. You can also
perform stapling manually.
► SADDLE STITCH FINISHER (LARGE STACKER) (page 1-127)
*1
(13) Paper pass unit
Relay between the machine and the finisher, finisher (large stacker),
saddle stitch finisher or saddle stitch finisher (large stacker).
*2
(14) Motion sensor
This sensor detects the presence of a person that
approaches the machine, and automatically wakes the
machine from sleep mode (Motion Sensor Mode Only).
*1
(15) Utility table
You can use this as a work platform, or temporarily place
originals or a mobile device.
• Do not place anything that weighs more than 5kg or
otherwise apply a load.
• Do not place a container that contains water or
other liquid. Risk of fire and electrical shock if the
liquid spills and enters the machine.
• Working on the table while the machine is in operation
may cause poor image quality or other problems.
(16) Bypass tray
Use this tray to feed paper manually.
When loading paper larger than A4R or 8-1/2" x 11"R,
pull out the extension guide.
► LOADING PAPER INTO THE BYPASS TRAY (page 1-76)
(17) Tray 5 (when a large capacity tray is installed)
Store paper in this tray.
► LOADING PAPER IN THE LARGE-CAPACITY TRAY
(when a large capacity tray is installed) (page 1-74)
(18) Tray 1
Store paper in this tray.
► TRAY 1 - 4 (when a low stand/550 sheet paper drawer
or stand/550/2x550/3x550/ 550&2100 sheet paper
drawer is installed) (page 1-69)
*1
(19) Finisher
This staples paper. A punch module can also be installed
to punch holes in output paper.
► FINISHER (page 1-116)
*1 Peripheral device.
Equipped standard or not available in some countries and regions. Not available on some models. Contact your dealer or
nearest authorised service representative.
*2 Can only be used on the MX-3060N/MX-3070N/MX-3560N/MX-3570N/MX-4060N/MX-4070N/MX-5070N/MX-6070N.
(12)
(21) (22)
*1
*1
(13) (14)
(23) (24)
(20) Saddle Stitch Finisher
This staples and folds paper. A punch module can also
be installed to punch holes in output paper.
► SADDLE STITCH FINISHER (page 1-123)
(21) Finisher (large stacker)
This staples paper. A punch module can also be installed
to punch holes in output paper. You can also perform
stapling manually.
► FINISHER (LARGE STACKER) (page 1-119)
(22) Punch module
This is used to punch holes in output. Requires an inner
finisher, finisher, finisher (large stacker), saddle stitch
finisher or saddle stitch finisher (large stacker).
(23) Tray 3 (when a stand/2x550/3x550 sheet paper
drawer is installed)
Store paper in this tray.
► TRAY 1 - 4 (when a low stand/550 sheet paper drawer
or stand/550/2x550/3x550/ 550&2100 sheet paper
drawer is installed) (page 1-69)
(24) Tray 4 (when a stand/3x550 sheet paper drawer is installed)
Store paper in this tray.
► TRAY 1 - 4 (when a low stand/550 sheet paper drawer
or stand/550/2x550/3x550/ 550&2100 sheet paper
drawer is installed) (page 1-69)
(25) Tray 2 (when a low stand/550 sheet paper drawer or stand/
550/2x550/3x550/550&2100 sheet paper drawer is installed)
Store paper in this tray.
► TRAY 1 - 4 (when a low stand/550 sheet paper drawer
or stand/550/2x550/3x550/ 550&2100 sheet paper
drawer is installed) (page 1-69)
(26) Tray 4 (when a stand/550&2100 sheet paper drawer is installed)
Store paper in this tray.
► TRAY 3 - 4 (when a stand/550&2100 sheet paper
drawer is installed) (page 1-72)
(27) Tray 3 (when a stand/550&2100 sheet paper drawer is installed)
Store paper in this tray.
► TRAY 3 - 4 (when a stand/550&2100 sheet paper
drawer is installed) (page 1-72)
1-4
(15) (16) (17) (18)
(25)
(26)
(27)
*1
*1
*1
*1
*1
*1
*1
*1