1. Manuals
  2. Brands
  3. Protech Systems Manuals
  4. Touch terminals
  5. PA-3222
  6. User manual

Protech Systems PA-3222 User Manual

10.1 inch pos terminal powered by intel celeron j1900 quad-core
Hide thumbs Also See for PA-3222:
Table of Contents

Advertisement

Quick Links

USER
MANUAL
PA-3222 M1
PA-3222
10.1" POS Terminal
Powered by Intel
J1900 Quad-Core
Celeron
®
®

Advertisement

Table of Contents
loading

Related Manuals for Protech Systems PA-3222

Summary of Contents for Protech Systems PA-3222

  • Page 1 USER MANUAL PA-3222 10.1” POS Terminal Powered by Intel Celeron ® ® J1900 Quad-Core PA-3222 M1...
  • Page 2 PA-3222 POS System With SATA/ 3COM/5USB COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in May 2017. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
  • Page 3 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4: Table Of Contents

    Contents Revision History ..................... ix Introduction ..................1-1 About This Manual ..............1-2 Getting Started ..................2-1 Package List ................2-2 System Views Without i-Button and Fingerprint Modules ..2-3 2.2.1 Front View ................. 2-3 2.2.2 Rear View ................2-3 2.2.3 Top View ................
  • Page 5 System Specifications ............. 2-14 Safety Precautions ..............2-16 System Configuration ................. 3-1 External System I/O Ports Diagram & Pin Assignment ..... 3-2 3.1.1 Rear I/O Ports Diagram ............. 3-2 Jumper & Connector Quick Reference Table ......3-3 Component Locations Of System Main Board ......3-4 3.3.1 Top View of System Main Board ........
  • Page 6 3.6.6 USB Connectors (USB6, USB7) ........3-18 3.6.7 LED Connector (LED1) ........... 3-19 3.6.8 Speaker Connector (SPK1_1) ......... 3-19 3.6.9 Power Connectors (DC12V, DC24V) ......3-20 3.6.10 Inverter Connector (INV1) ..........3-21 3.6.11 Reserved Connectors (SPK2_1, GPIO1) ......3-21 3.6.12 Panel Resolution Selection (JP5, JP6)......
  • Page 7 3.7.4 Printer Board: MB-1030 series ........3-37 3.7.4.1 Jumper & Connector Quick Reference Table....3-38 3.7.5 Setting Printer Board Connectors and Jumpers ....3-39 3.7.5.1 Power Supply Connector ..........3-39 3.7.5.2 RS-232 Interface Connector ........3-39 3.7.5.3 Thermal Head/Motor/Sensor Connector ...... 3-40 3.7.5.4 Auto-Cutter Connector ..........
  • Page 8 3.9.1 ID TECH ................3-54 3.9.1.1 Main Connector ............3-54 3.9.2 MB-3012 ................3-55 3.9.2.1 Information Button Reader ........... 3-55 3.9.2.2 Output Connector ............3-55 Software Utilities ................. 4-1 Introduction ................4-2 ® Installing Intel Chipset Software Installation Utility ....4-3 ®...
  • Page 9 4.9.4.2 OPOS MSR Register ........... 4-77 4.9.4.3 OPOS MSR Tester ............4-85 4.10 API ................... 4-89 4.10.1 API Package Content ............4-89 4.10.2 API Procedure ..............4-90 4.10.3 Cash Drawer ..............4-93 4.10.4 Watchdog ................. 4-94 4.11 API Function ................4-95 4.11.1 Cash Drawer Function .............
  • Page 10 Chipset ..................5-28 5.5.1 North Bridge ..............5-29 North Bridge – LCD Control ......... 5-30 5.5.1.1 5.5.2 South Bridge ..............5-31 Security ................... 5-32 Boot ..................5-33 Boot – Hard Drive BBS Priorities ........5-34 5.7.1 Save & Exit ................5-35 Appendix A System Diagrams ............
  • Page 11 Configuring WatchDog Timer ..............B-10 Flash BIOS Update .................B-13 viii...

  • Page 12: Revision History

    Revision History The revision history of PA-3222 User Manual is described below: Version No. Revision History Page No. Date Initial Release 2017/05/10...

  • Page 13: Introduction

    Introduction This chapter provides the introduction for the PA-3222 system as well as the framework of the user manual. The following topic is included: • About This Manual PA-3222 SERIES USER MANUAL Page: 1-1...

  • Page 14: About This Manual

    Chapter 1 Introduction 1.1 About This Manual Thank you for purchasing our PA-3222 system. The PA-3222 is an updated system designed to be comparable with the highest performance of IBM AT personal computers. The PA-3222 provides faster processing speed, greater expandability and can handle more tasks than before.

  • Page 15: Getting Started

    Getting Started This chapter provides the information for the PA-3222 system. It describes how to set up the system quickly and outlines the system specifications. The following topics are included: • Package List • System Overview • System Diagrams • System Specification •...

  • Page 16: Package List

    Item Q’ty PA-3222 Manual / Driver DVD Quick Reference Guide AC Power Cord (Optional) MSR Card Reader (Optional) i-Button + MSR Card Reader (Optional) Wireless LAN (IEEE 802.11 b+g) (Optional) VFD (Optional) PA-3222 SERIES USER MANUAL Page: 2-2...

  • Page 17: System Views Without I-Button And Fingerprint Modules

    Chapter 2 Getting Started 2.2 System Views Without i-Button and Fingerprint Modules 2.2.1 Front View Unit: mm Without i-Button Without Fingerprint 2.2.2 Rear View PA-3222 SERIES USER MANUAL Page: 2-3...

  • Page 18: Top View

    Chapter 2 Getting Started 2.2.3 Top View Without i-Button 298.29 Without i-Button PA-3222 SERIES USER MANUAL Page: 2-4...

  • Page 19: Bottom View

    Chapter 2 Getting Started 2.2.4 Bottom View 2.2.5 Quarter View Without i-Button PA-3222 SERIES USER MANUAL Page: 2-5...

  • Page 20: Side View

    Chapter 2 Getting Started 2.2.6 Side View Unit: mm Without Fingerprint module Without Fingerprint PA-3222 SERIES USER MANUAL Page: 2-6...

  • Page 21: System Views With I-Button Module

    Chapter 2 Getting Started 2.3 System Views With i-Button Module 2.3.1 Front View 2.3.2 Rear View PA-3222 SERIES USER MANUAL Page: 2-7...

  • Page 22: Top View

    Chapter 2 Getting Started Top View 2.3.3 With i-Button 298.29 With i-Button PA-3222 SERIES USER MANUAL Page: 2-8...

  • Page 23: Bottom View

    Chapter 2 Getting Started 2.3.4 Bottom View 2.3.5 Quarter View With i-Button PA-3222 SERIES USER MANUAL Page: 2-9...

  • Page 24: Side View

    Chapter 2 Getting Started 2.3.6 Side View PA-3222 SERIES USER MANUAL Page: 2-10...

  • Page 25: System Views With Fingerprint Module

    Chapter 2 Getting Started 2.4 System Views With Fingerprint Module 2.4.1 Front View 2.4.2 Rear View PA-3222 SERIES USER MANUAL Page: 2-11...

  • Page 26: Top View

    Chapter 2 Getting Started 2.4.3 Top View PA-3222 SERIES USER MANUAL Page: 2-12...

  • Page 27: Bottom View

    Chapter 2 Getting Started 2.4.4 Bottom View 2.4.5 Side View With Fingerprint PA-3222 SERIES USER MANUAL Page: 2-13...

  • Page 28: System Specifications

     8-bit grayscale, reader Fingerprint Display  10.1" TFT LCD  1280 x 800 Resolution  400 cd/m² Brightness  10.1" Capacitive Touch panel, USB interface (EETI Touch Screen controller)  24 ~ 30 degree Tilt Angle PA-3222 SERIES USER MANUAL Page: 2-14...
  • Page 29 Chapter 2 Getting Started Environment  CE / FCC EMC & Safety  0°C ~ 35°C (32°F ~ 95°F) Operating Temp.  -5°C ~ 60°C (23°F ~ 140°F) Storage Temp.  20% ~ 90% Humidity PA-3222 SERIES USER MANUAL Page: 2-15...

  • Page 30: Safety Precautions

    Avoid direct sunlight exposure for a long period of time (for example, in a closed car in summer time. Also avoid the system from any heating device.). Or do not use PA-3222 when it has been left outdoors in a cold winter day. •...

  • Page 31: System Configuration

    • Printer Board Component Locations & Pin Assignment • Setting Printer Board Connectors and Jumpers PDAC-3100  MB-1030 series  MB-1011 & MB-1013  • Setting VFD Board Connectors and Jumpers • Setting MSR PA-3222 SERIES USER MANUAL Page: 3-1...

  • Page 32: External System I/O Ports Diagram & Pin Assignment

    Rear I/O Ports Diagram DRW2 COM4 (Option 2) DIS PWR (Option 1) DC IN 1/2/3 DRW1 USB0 COM1 COM3 (Option 3) COM2 DRW1 extended with Y cable DRW1-1 DRW1-2 Side I/O Power USB5 Button PA-3222 SERIES USER MANUAL Page: 3-2...

  • Page 33: Jumper & Connector Quick Reference Table

    Speaker Connector SPK1_1 Power Connector DC12V, DC24V Inverter Connector INV1 Reserved Connectors SPK2_1, GPIO1 MSR / Card Reader Connector LVDS Connector LVDS1 SATA1, SATA2, SATA_PWR1, SATA & SATA Power Connectors SATA_PWR2 Mini-PCIe Connector M_PCI_E1 PA-3222 SERIES USER MANUAL Page: 3-3...

  • Page 34: Component Locations Of System Main Board

    Chapter 3 Hardware Configuration 3.3 Component Locations Of System Main Board 3.3.1 Top View of System Main Board Figure 3-1 Main Board Component Location (Top View) PA-3222 SERIES USER MANUAL Page: 3-4...
  • Page 35 Make sure both the system and peripheral devices are turned OFF as sudden surge of power could damage sensitive components. Make sure PA-3222 is properly grounded. CAUTION: Observe precautions while handling electrostatic sensitive components. Make sure to ground yourself to prevent static charge while you are working on the connectors and jumpers.

  • Page 36: How To Set Jumpers

    2 to create one setting and shorting. You can also select to connect pins 2 and 3 to create another setting. The format of the jumper picture will be illustrated throughout this manual. The figure below shows different types of jumpers and jumper settings. PA-3222 SERIES USER MANUAL Page: 3-6...
  • Page 37 Chapter 3 Hardware Configuration Jumper diagrams Jumper settings PA-3222 SERIES USER MANUAL Page: 3-7...

  • Page 38: Function Buttons And I/O Ports

    Description: DC Power-In Port (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT +24V +24V DC_IN 3.5.3 VGA Port (VGA) Port Name: VGA Description: VGA Port, D-Sub 15-pin (rear I/O) PIN ASSIGNMENT PIN ASSIGNMENT GREEN BLUE DDCA DATA HSYNC VSYNC DDCA CLK PA-3222 SERIES USER MANUAL Page: 3-8...

  • Page 39: Com Ports (Com1, Com2, Com3)

    COM4_1 is selected as the printer control interface. Port Name: COM4 (optional) Description: D-Sub9 Serial Port (rear I/O), Co-lay with COM4_1 ASSIGNMENT ASSIGNMENT COM4/ (optional) RI/+5V/+12V selectable (Max. current: 1A) PA-3222 SERIES USER MANUAL Page: 3-9...

  • Page 40: Usb Ports (Usb0, Usb1, Usb2, Usb3, Usb5)

    Ethernet connection. RB Ver. LAN LED Color Status Description Indicator Left Side Orange Blink Giga LAN connection is activated. Green Blink 10/100Mbps LAN connection is activated. Right Side Green LAN switch/hub connected. PA-3222 SERIES USER MANUAL Page: 3-10...

  • Page 41: Cash Drawer Port (Drw1)

    Chapter 3 Hardware Configuration 3.5.7 Cash Drawer Port (DRW1) Port Name: DRW1 Description: DRW1 is used by default. ASSIGNMENT DRW2 Sense GPIO1 / DRW1 Draw1 Sense 12V/24V (Max. current: 1A) DRW1 GPIO2 / DRW2 PA-3222 SERIES USER MANUAL Page: 3-11...

  • Page 42: Setting Main Board Connectors And Jumpers

    SETTING (Default Setting) JP_COM2 JP_COM3 +12V JP_COM3 JP_COM2 JP_COM2 JP_COM3 COM1 / COM4 /DRW1 The voltages of the external ports "COM1 & COM4 & Cash Drawer" can be adjusted via BIOS for your convenience. PA-3222 SERIES USER MANUAL Page: 3-12...

  • Page 43: I-Button Connector (I-But)

    Jumper Name: JP10, JP11, JP12 Description: i-Button Function Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION COM2 JP10/JP11/JP12/ (Default Setting) I-BUT* JP10/JP11/JP12/ *COM2 & COM2_1 will not function when jumpers JP10, JP11 & JP12 are set as “I-BUT”. PA-3222 SERIES USER MANUAL Page: 3-13...

  • Page 44: Cash Drawer Control Selection (Jp15)

    You can split DRW1 into two channels of DRW1-1 & DRW1-2 using the Y-Cable (option). Jumper Name: JP15 Description: Cash Drawer 2 Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION DRW1-1 & DRW1-2 JP15 DRW1-1 only JP15 PA-3222 SERIES USER MANUAL Page: 3-14...
  • Page 45 Chapter 3 Hardware Configuration RJ11 DRW1-1 Step 3. DRW1, DRW1-1, DRW1-2 shares the same power source. (Default: 12V). SIO Address Cash drawer 1 LDN 06, 0x91 bit 2 Cash drawer 2 LDN 06, 0x91 bit 3 PA-3222 SERIES USER MANUAL Page: 3-15...
  • Page 46 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. PA-3222 SERIES USER MANUAL Page: 3-16...
  • Page 47 Note: The DRW2 Port can function only when the optional "Printer Kit" is installed on PA-3222. The DRW2 signals from the printer board (MB-1030, MB-1011, MB-1013, PDAC-3100) can be controlled via relevant commands. See the picture below for the location of DRW2 port:...

  • Page 48: Usb Connectors (Usb6, Usb7)

    “MINI-PCIE” port. USB6/ USB6 can function only when JP13 is set as 1-3, 2-4[short]. USB7 USB7 signal is shared from the “Touch Controller”. USB7 can function only when JP8, JP9 are set as 1-2[short]. PA-3222 SERIES USER MANUAL Page: 3-18...

  • Page 49: Led Connector (Led1)

    Chapter 3 Hardware Configuration 3.6.7 LED Connector (LED1) Connector Name: LED1 Description: Power indication LED connector ASSIGNMENT PWR_LED LED1 3.6.8 Speaker Connector (SPK1_1) Connector Name: SPK1_1 Description: Speaker Connector ASSIGNMENT HD_FRONT-OUT-R HD_FRONT-OUT-L SPK1_1 PA-3222 SERIES USER MANUAL Page: 3-19...

  • Page 50: Power Connectors (Dc12V, Dc24V)

    Chapter 3 Hardware Configuration 3.6.9 Power Connectors (DC12V, DC24V) Connector Name: DC12V Description: DC 12 Voltage Provider Connector ASSIGNMENT VCC12 VCC12 DC12V Connector Name: DC24V Description: Power for Thermal Printer Connector ASSIGNMENT VCC24 VCC24 DC24V PA-3222 SERIES USER MANUAL Page: 3-20...

  • Page 51: Inverter Connector (Inv1)

    Description: External audio phone jack reserved connector ASSIGNMENT HD_FRONT-OUT-L SPK2_1 HD_FRONT-OUT-R Connector Name: GPIO1 Description: 2 ports GPIO & DC5V & DC3.3V reserved connector ASSIGNMENT GPIO1 GPIO2 5V (Maximum current: 0.5A) 3.3V ((Maximum current: 0.5A) GPIO1 PA-3222 SERIES USER MANUAL Page: 3-21...

  • Page 52: Panel Resolution Selection (Jp5, Jp6)

    Mini PCIE USB Selection (JP13) Jumper Name: JP13 Description: "USB6 signal support to" selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION USB signal to 3-5, 4-6 mini-PCIE JP13 USB signal to 1-3, 2-4 USB6 wafer (Default Setting) JP13 PA-3222 SERIES USER MANUAL Page: 3-22...

  • Page 53: Msr / Card Reader Connector (Ps2)

    Chapter 3 Hardware Configuration 3.6.14 MSR / Card Reader Connector (PS2) Connector Name: PS2 Description: MSR / Card reader connector ASSIGNMENT KB_CLK (Output) KB_CLK_C (Input) KB_DATA_C (Input) KB_DATA (Output) PA-3222 SERIES USER MANUAL Page: 3-23...

  • Page 54: Lvds Connector (Lvds1)

    LVDS Connector (LVDS1) Connector Name: LVDS1 Description: LVDS Connector ASSIGNMENT ASSIGNMENT LVDS_VCC PANEL_Reverse LVDS_CLKB_D- LVDS_CLKB_D+ LVDS_B2_D- LVDS_B2_D+ LVDS_B1_D- LVDS_B1_D+ LVDS_B3_D+ LVDS_B3_D- LVDS_B0_D+ LVDS_B0_D- LVDS_CLKA_D+ VDS_CLKA_D- LVDS_A2_D+ LVDS_A2_D- LVDS_A1_D+ LVDS_A1_D- LVDS1 LVDS_A0_D+ LVDS_A0_D- LVDS_A3_D+ LVDS_A3_D- LVDS_VCC LVDS_VCC PA-3222 SERIES USER MANUAL Page: 3-24...

  • Page 55: Touch Panel Signal Interface Selection (Jp8, Jp9)

    Chapter 3 Hardware Configuration 3.6.16 Touch Panel Signal Interface Selection (JP8, JP9) Jumper Name: JP8, JP9 Description: Control connectors for touch panel signal interface JUMPER SELECTION JUMPER ILLUSTRATION SETTING USB7 JP8: 1-2 Connector JP9: 1-2 PA-3222 SERIES USER MANUAL Page: 3-25...

  • Page 56: Sata & Sata Power Connector

    3.6.17 SATA & SATA Power Connector (SATA1, SATA2, SATA_PWR1, SATA_PWR2) Connector Name: SATA1, SATA2 Description: Serial ATA connectors ASSIGNMENT SATA1 SATA2 Connector Name: SATA_PWR1, SATA_PWR2 Description: Serial ATA power connectors ASSIGNMENT SATA_PWR1 VCC12 SATA_PWR2 PA-3222 SERIES USER MANUAL Page: 3-26...

  • Page 57: Bios Update Selection (Jp1)

    Step 4. Power on the PC and the PC will then auto-reboot for once in order to set SoC’s register. Step 5. Done! SELECTION JUMPER SETTING JUMPER ILLUSTRATION Open Normal (Default Setting) Clear CMOS* Note: Please make sure the main power is off before you clear CMOS data. . PA-3222 SERIES USER MANUAL Page: 3-27...

  • Page 58: Lvds Link (Jp16)

    Jumper Illustration JP16 JP16 Default Setting: NC (software controlled). 3.6.21 LVDS Voltage Selection (JP17) Jumper Name: JP17 Description: LVDS Voltage Selection Selection Jumper Setting Jumper Illustration 3-5, 4-6 3.3V (Default Setting) JP17 1-3, 2-4 JP17 PA-3222 SERIES USER MANUAL Page: 3-28...

  • Page 59: Panel Enable Selection (Jp20)

    +1.5V CLKREQ# Reserved Reserved REFCLK1- Reserved M_PCI_E1 REFCLK1+ Reserved Reserved Reserved Reserved Reserved PERST# PERn0 +3.3SB PERp0 +1.5V SMB_CLK PETn2 SMB_DATA PETp2 USB D- USB D+ +3.3V +3.3V Reserved Reserved Reserved +1.5V Reserved +3.3V PA-3222 SERIES USER MANUAL Page: 3-29...

  • Page 60: Printer Board Component Locations & Pin Assignment

    Chapter 3 Hardware Configuration 3.7 Printer Board Component Locations & Pin Assignment 3.7.1 Printer Board: PDAC-3100 Figure 3-2. PDAC-3100 Printer Board Component Locations PA-3222 SERIES USER MANUAL Page: 3-30...

  • Page 61: Jumper & Connector Quick Reference Table

    Chapter 3 Hardware Configuration 3.7.2 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector RS-232 Interface Connector Auto-Cutter Connector USB Connector Thermal Head/Motor/Sensor Connector Terminal Assignment Connector PA-3222 SERIES USER MANUAL Page: 3-31...

  • Page 62: Setting Printer Board Connectors And Jumpers: Pdac-3100

    Chapter 3 Hardware Configuration 3.7.3 Setting Printer Board Connectors and Jumpers: PDAC-3100 3.7.3.1 Power Supply Connector CN1: Power supply wafer ASSIGNMENT +24V +24V 3.7.3.2 RS-232 Interface Connector CN7: RS-232 interface connector ASSIGNMENT ASSIGNMENT PA-3222 SERIES USER MANUAL Page: 3-32...
  • Page 63 2A-2 Auto-cutter motor drive signal 1B-1 Auto-cutter motor drive signal 1B-2 Auto-cutter motor drive signal 1A-1 Auto-cutter motor drive signal 1A-2 Auto-cutter motor drive signal 3.7.3.4 USB Connector CN8: USB Connector ASSIGNMENT ASSIGNMENT Vbus PA-3222 SERIES USER MANUAL Page: 3-33...
  • Page 64 Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND Head GND LATCH Print data latch Head drive power Head drive power Head drive power Head drive power PA-3222 SERIES USER MANUAL Page: 3-34...
  • Page 65 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-3222 SERIES USER MANUAL Page: 3-35...
  • Page 66 Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused PA-3222 SERIES USER MANUAL Page: 3-36...

  • Page 67: Printer Board: Mb-1030 Series

    Chapter 3 Hardware Configuration 3.7.4 Printer Board: MB-1030 series CUT_CN1 COM1 9 10 USB_CN1 24V_CN1 PRINT_CN1 Figure 3-3. MB-1030 Printer Board Component Locations PA-3222 SERIES USER MANUAL Page: 3-37...

  • Page 68: Auto-Cutter Connector

    Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector 24V_CN1 RS-232 Interface Connector COM1 Thermal Head/Motor/Sensor Connector PRINT_CN1 Auto-Cutter Connector CUT_CN1 Paper-Near-END Sensor Connector USB Interface Connector USB_CN1 Terminal Assignment Connector PA-3222 SERIES USER MANUAL Page: 3-38...

  • Page 69: Setting Printer Board Connectors And Jumpers

    Setting Printer Board Connectors and Jumpers 3.7.5.1 Power Supply Connector 24V_CN1: Power Supply Wafer ASSIGNMENT +24V +24V 24V_CN1 3.7.5.2 RS-232 Interface Connector COM1: RS-232 Interface Connector ASSIGNMENT ASSIGNMENT DSR /CTS DTR /RTS 9 10 COM1 PA-3222 SERIES USER MANUAL Page: 3-39...

  • Page 70: Thermal Head/Motor/Sensor Connector

    Head strobe signal DST1 Head strobe signal Head GND Head GND Head GND Head GND Head GND Head GND LATCH Print data latch Head drive power Head drive power Head drive power Head drive power PA-3222 SERIES USER MANUAL Page: 3-40...
  • Page 71 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-3222 SERIES USER MANUAL Page: 3-41...
  • Page 72 1A-2 Auto-cutter motor drive signal 3.7.5.5 Paper-Near-END Sensor Connector CN2: Paper-near-end sensor connector ASSIGNMENT FUNCTION Power supply of the near end sensor Signal of the near end sensor GND of the near end sensor PA-3222 SERIES USER MANUAL Page: 3-42...

  • Page 73: Terminal Assignment Connector

    Feed signal RESET Reset signal Status signal Status signal Status signal Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused PA-3222 SERIES USER MANUAL Page: 3-43...

  • Page 74: Printer Board: Mb-1011 & Mb-1013

    Chapter 3 Hardware Configuration 3.7.6 Printer Board: MB-1011 & MB-1013 Figure 3-4. MB-1011 & MB-1013 Printer Board Component Locations PA-3222 SERIES USER MANUAL Page: 3-44...

  • Page 75: Jumper & Connector Quick Reference Table

    Chapter 3 Hardware Configuration 3.7.6.1 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Supply Connector RS-232 Interface Connector Auto-Cutter Connector Thermal Head/Motor/Sensor Connector Terminal Assignment Connector USB Interface Connector PA-3222 SERIES USER MANUAL Page: 3-45...

  • Page 76: Setting Printer Board Connectors And Jumpers: Mb-1011

    Chapter 3 Hardware Configuration 3.7.7 Setting Printer Board Connectors and Jumpers: MB-1011 & MB-1013 3.7.7.1 Power Supply Connector CN1: Power supply wafer ASSIGNMENT +24V +24V 3.7.7.2 RS-232 Interface Connector CN7: RS-232 interface connector ASSIGNMENT ASSIGNMENT PA-3222 SERIES USER MANUAL Page: 3-46...

  • Page 77: Auto-Cutter Connector

    Head drive power Head drive power Head drive power Head drive power Print data output Synchronizing signal for print data transfer Head GND Head GND Head GND Head GND Head GND Head GND Unused PA-3222 SERIES USER MANUAL Page: 3-47...
  • Page 78 Power supply of the out-of-paper sensor GND of the platen position/ out-of-paper sensor Signal of the platen position sensor Unused Frame GND Frame GND Unused Motor drive signal Motor drive signal Motor drive signal Motor drive signal PA-3222 SERIES USER MANUAL Page: 3-48...

  • Page 79: Terminal Assignment Connector

    Status signal Drawer sensor signal Drawer switch signal Drive terminal for the drawer (Vp side) GNDdu Drive terminal for the drawer (GND side) Unused 3.7.7.6 USB Interface Connector CN8: USB interface connector ASSIGNMENT Vbus PA-3222 SERIES USER MANUAL Page: 3-49...

  • Page 80: Vfd Board Component Locations & Pin Assignment

    Chapter 3 Hardware Configuration 3.8 VFD Board Component Locations & Pin Assignment 3.8.1 VFD Board: MB-4103, LD720 JP12V Figure 3-5. MB-4103 & LD720 VFD Board Component Locations PA-3222 SERIES USER MANUAL Page: 3-50...

  • Page 81: Jumper & Connector Quick Reference Table

    Chapter 3 Hardware Configuration 3.8.2 Jumper & Connector Quick Reference Table Jumper / Connector NAME Power Switch Selection JP12V RS-232 Serial Interface Connector PA-3222 SERIES USER MANUAL Page: 3-51...

  • Page 82: Setting Mb-4103 & Ld720 Vfd Board Connectors And

    Chapter 3 Hardware Configuration 3.8.3 Setting MB-4103 & LD720 VFD Board Connectors and Jumpers 3.8.3.1 Power Switch Selection JP12V: Power Switch Selection SELECTION JUMPER SETTING JUMPER ILLUSTRATION JP12V (Default) JP12V PA-3222 SERIES USER MANUAL Page: 3-52...

  • Page 83: Serial Interface Connector

    Chapter 3 Hardware Configuration 3.8.3.2 RS-232 Serial Interface Connector CN1: RS-232 serial interface wafer ASSIGNMENT ASSIGNMENT +12V/+5V PA-3222 SERIES USER MANUAL Page: 3-53...

  • Page 84: Msr Board Component Locations & Pin Assignment

    3.9 MSR Board Component Locations & Pin Assignment 3.9.1 ID TECH ID-TECH MSR Board Component Locations 3.9.1.1 Main Connector ASSIGNMENT ASSIGNMENT K-CLK Chassis Ground (Computer connections) P-CLK K-DATA (Keyboard connections) (Computer connections) P-DATA (Keyboard connections) +5V Vcc PA-3222 SERIES USER MANUAL Page: 3-54...

  • Page 85: Information Button Reader

    MB-3012 MSR Board Component Locations 3.9.2.1 Information Button Reader I_BUTTON1: Information button reader ASSIGNMENT I_B1 I_BUTTON1 3.9.2.2 Output Connector IO1: Output wafer ASSIGNMENT ASSIGNMENT CLK_KB RX_MSR CLK_PC TX_MSR DATA_KB DATA_PC USB_D+_R USB_D-_R CHASSIS GND PA-3222 SERIES USER MANUAL Page: 3-55...

  • Page 86: Software Utilities

    • Installing Sound Driver Utility • Installing Fingerprint Driver Utility (Optional) • Installing RFID Module Driver Utility (Optional) • Installing Wireless Module Driver Utility (Optional) • Peripheral Devices - Printer - VFD - MSR • API PA-3222 SERIES USER MANUAL Page: 4-1...

  • Page 87: Introduction

    Chapter 4 Software Utilities 4.1 Introduction Enclosed with the PA-3222 Series package is our driver utilities contained in a DVD-ROM disk. Refer to the following table for driver locations: Filename (Assume that Win7 Win8.1 Win10 Purpose DVD- ROM drive is D :)

  • Page 88: Installing Intel

    10 series, and it should be installed right after the OS installation. Please follow the steps below: Connect the USB DVD-ROM device to PA-3222 and insert the driver disk. Enter the “Main Chip” folder where the Chipset driver is located (depending on your OS platform).

  • Page 89: Installing Vga Driver Utility

    Chapter 4 Software Utilities 4.3 Installing VGA Driver Utility The VGA interface embedded with PA-3222 can support a wide range of display types. You can have dual displays via CRT & LVDS interfaces work simultaneously. To install the Graphics driver, follow the steps below: Connect the USB DVD-ROM device to PA-3222 and insert the driver disk.
  • Page 90 Follow the on-screen instructions to complete the installation. Once the installation is completed, shut down the system and restart PA-3222 for the changes to take effect. For more details on the Installation procedure, please refer to the Readme.txt file found on LAN Driver Utility.

  • Page 91: Installing Sound Driver Utility

    8.1 & Windows 10 series. To install the Sound Driver, follow the steps below: Connect the USB DVD-ROM device to PA-3222 and insert the driver disk. Enter the “Sound” folder where the sound driver is located (depending on your OS platform).

  • Page 92: Installing Fingerprint Driver Utility (Optional)

    OS installation. To install the fingerprint driver, follow the steps below: Connect the USB DVD-ROM device to PA-3222 and insert the driver disk. Enter the “Device\Embedded Finger Printer” folder where the fingerprint driver is located.

  • Page 93: Installing Wireless Module Driver Utility (Optional)

    10 series, and it should be installed right after the OS installation. To install the wireless driver, follow the steps below: Connect the USB DVD-ROM device to PA-3222 and insert the driver disk. Enter the “Device\Embedded Wireless Module” folder where the wireless driver is located.

  • Page 94: Peripheral Devices

    GS h FS q GS k ESC 2 GS ! GS r ESC 3 GS $ GS v 0 ESC = GS * GS w ESC ? GS ( A ESC @ GS ( K PA-3222 SERIES USER MANUAL Page: 4-9...

  • Page 95: Commands List

    Print data in page mode Ignored <ESC SP> 1B 20 Set right-side character spacing <ESC !> 1B 21 Select print mode(s) <ESC $> 1B 24 Set absolute print position. <ESC *> 1B 2A Select bit image mode Page: 4-10 PA-3222 SERIES USER MANUAL...
  • Page 96 1D 2A Define download bit images <GS ( A> 1D 28 41 Execute test print Disabled <GS ( K> 1D 28 4B Set print density Disabled ● <GS /> 1D 2F Print download bit image PA-3222 SERIES USER MANUAL Page: 4-11...
  • Page 97 ● <GS k> 1D 6B Print bar code <GS r> 1D 72 Transmit status ● <GS v 0> 1D 76 30 Print raster bit image Disabled <GS w> 1D 77 Set bar code width Page: 4-12 PA-3222 SERIES USER MANUAL...
  • Page 98 ●: Enabled only when data is not present in the printer buffer. ▲: Only value setting is possible. Disabled: Parameters are processed as printable data. Ignored: All command codes including parameters are ignored and nothing is executed. PA-3222 SERIES USER MANUAL Page: 4-13...
  • Page 99  After execution, makes the top of the line the next print starting position. [Name] Print and recover to standard mode (in page mode) ASCII [Format] Hex. Decimal 12 [Range] Prints all buffered data to the print region collectively, then recovers to the standard [Description] mode. Page: 4-14 PA-3222 SERIES USER MANUAL...
  • Page 100 Deletes all print data in the currently set print region in page mode.  This command is enabled only in page mode. [Description]  Portions included in the currently set print region are also deleted, even if previously set print region data. PA-3222 SERIES USER MANUAL Page: 4-15...
  • Page 101 No error. Error occurs. Not used. Fixed to Off. n = 3 : Error status On / Off Decimal Function Not used. Fixed to Off. Not used. Fixed to On. Not used. Fixed to Off. Page: 4-16 PA-3222 SERIES USER MANUAL...
  • Page 102 = 1: Recover from the error and start printing from the line where the error [Description] occurred. n = 2: Recover from error after clearing the reception buffer and print buffer. This command is enabled even when the printer specification is disabled by ESC = (select peripheral devices). PA-3222 SERIES USER MANUAL Page: 4-17...
  • Page 103 [Format] Hex. Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 0 This command sets the size of space to right of character. [Description] Right space = n × [horizontal motion units]. Page: 4-18 PA-3222 SERIES USER MANUAL...
  • Page 104 This command specifies the next print starting position in reference to the left edge of the print area. The printing start position is calculated using (nL + nH x [Description] 256) x (vertical or horizontal motion units). Specifications exceeding the print range are ignored. PA-3222 SERIES USER MANUAL Page: 4-19...
  • Page 105 67 DPI 101 DPI nL+nH×256 density 8 dot double 67 DPI 203 DPI nL+nH×256 density 24 dot (nL+nH×256) single 203 DPI 101 DPI ×3 density 24 dot (nL+nH×256) double 203 DPI 203 DPI ×3 density Page: 4-20 PA-3222 SERIES USER MANUAL...
  • Page 106 Hex. Decimal 0 ≤ n ≤ 255 [Range] Initial Value n = 34 This command sets the line spacing using a following rule. [Description] Line spacing = n x (vertical or horizontal motion units) PA-3222 SERIES USER MANUAL Page: 4-21...
  • Page 107  n specifies the column number for setting a horizontal tab position from the [Description] left margin or the beginning of the line.  k indicates the number of horizontal tab positions to be set. Page: 4-22 PA-3222 SERIES USER MANUAL...
  • Page 108  In page mode, this command functions as follows, depending on the starting position of the printable area: (1) When the starting position is set to the upper left or lower right of the printable area using ESC T, the vertical motion unit (y) is used. PA-3222 SERIES USER MANUAL Page: 4-23...
  • Page 109 FS q : Define NV bit image c. GS v 0 : Print raster bit images d. GS L : Set left margin  Recover to standard mode using ESC @ (initialize printer). Page: 4-24 PA-3222 SERIES USER MANUAL...
  • Page 110 Initial Value n = 0 [Description] This command specifies international characters according to n values. Character Set France Germany Denmark I Sweden Italy Spain Japan Norway Denmark II Spain II Latin America Korea Russia Slavonic PA-3222 SERIES USER MANUAL Page: 4-25...
  • Page 111 GS $ :Specify absolute position for character vertical direction in page Mode GS \: :Specify relative position for character vertical direction in page mode  Standard mode is selected when the power is turned on, the printer is reset or initialized (ESC @). Page: 4-26 PA-3222 SERIES USER MANUAL...
  • Page 112  Underlines are not applied to characters rotated 90 degrees clockwise even when ESC !,ESC - or FS - commands are given.  If 90 degree clockwise rotation is specified, double-wide and double-tall commands in the 90 rotation mode enlarges characters in the opposite PA-3222 SERIES USER MANUAL Page: 4-27...
  • Page 113 - horizontal starting position).  If (vertical starting position + printing area height) exceeds the printable area, the printing area height is automatically set to (vertical printable area [Description] - vertical starting position). Page: 4-28 PA-3222 SERIES USER MANUAL...
  • Page 114 This command specifies position alignment for all data in one line in standard mode, using n as follows: Alignment Left alignment [Description] Center alignment Right alignment This command has no effect in page mode. PA-3222 SERIES USER MANUAL Page: 4-29...
  • Page 115 Selects the paper out detector to stop printing when paper has run out. “0” “1” Function Undefined Undefined Undefined [Description] Undefined Undefined Undefined Paper roll near end detector Invalid Valid Paper roll near end detector Invalid Valid Page: 4-30 PA-3222 SERIES USER MANUAL...
  • Page 116 This command executes a full cut of the paper in standard mode ESC m [Name] Partial cut. ASCII [Format] Hex. Decimal [Range] This command executes a partial cut of the paper with one point uncut in [Description] standard mode. PA-3222 SERIES USER MANUAL Page: 4-31...
  • Page 117 Hex. Decimal 0 ≤ n ≤ 8 [Range] Initial Value n = 0 Select page n of the character code table. Character set CP-437 Katakana CP-850 [Description] CP-852 CP-860 CP-863 CP-865 CP-1252 User Define Page: 4-32 PA-3222 SERIES USER MANUAL...
  • Page 118  NV bit image is a bit image defined in non-volatile memory by FS q and printed by this command.  This command is ignored when the specified NV bit image n is undefined. PA-3222 SERIES USER MANUAL Page: 4-33...
  • Page 119  xL and xH specify the horizontal direction for one NV bit image (xL + xH x 256) x 8 dots.  yL and yH specify the vertical direction for one NV bit image (yL + yH x 256) x 8 dots. Page: 4-34 PA-3222 SERIES USER MANUAL...
  • Page 120 4 times 5 times 6 times 7 times 8 times Table 2 [Enlarged in vertical direction] Decimal Enlargement 1 time(standard) 2 times 3 times 4 times 5 times 6 times 7 times 8 times PA-3222 SERIES USER MANUAL Page: 4-35...
  • Page 121 [(nL + nH x 256) x basic [Description] calculated pitch] from the starting point.  When not in page mode, this command is ignored.  Specifications for absolute positions that exceed the specified print range are ignored. Page: 4-36 PA-3222 SERIES USER MANUAL...
  • Page 122  Horizontal direction dot count is X x 8 dots; Vertical direction dot count is Y x 8 dots  d indicates the bit-image data. Bits that correspond to the dots to print are 1, and the bits that correspond to the dots that are not printed are 0. [Description] PA-3222 SERIES USER MANUAL Page: 4-37...
  • Page 123 Basic sheet (paper roll) [Description] 1 , 49 Paper Roll 2 , 50 m specifies a test pattern.. Type of Test Print 2 , 50 Printer Status (Self Print) 3 , 51 Rolling Pattern Print Page: 4-38 PA-3222 SERIES USER MANUAL...
  • Page 124 This command prints the downloaded bit image defined by GS * according to the mode denoted by m. Vertical dot Horizontal dot Mode [Description] density(DPI) density(DPI) 0 , 48 Normal 1 , 49 Double-width 2 , 50 Double-height 3 , 51 Quadruple PA-3222 SERIES USER MANUAL Page: 4-39...
  • Page 125 Selects the printing position of HRI characters when printing bar codes. Printing Position 0, 48 No print [Description] 1, 49 Above bar code 2, 50 Below bar code 3, 51 Above and below bar code(both) Page: 4-40 PA-3222 SERIES USER MANUAL...
  • Page 126 0 ≤ nL ≤ 255, 0 ≤ nH ≤ 255 [Range] Initial Value (nL + nH x 256)=0 (nL=0, nH=0) nL and nH set the specified left margin. The left margin is [(nL + nH x 256) x basic calculated pitch]. [Description] PA-3222 SERIES USER MANUAL Page: 4-41...
  • Page 127 Feeds paper to (cutting position + [n x basic calculated pitch]) and performs a full cut Feeds paper to (cutting position + [n x basic calculated pitch]) and performs a partial cut (one point uncut) Page: 4-42 PA-3222 SERIES USER MANUAL...
  • Page 128 [(nL + nH x 256) x basic calculated pitch] for the next data expanding starting position.  When not in page mode, this command is ignored. PA-3222 SERIES USER MANUAL Page: 4-43...
  • Page 129 Cover is open Not used. Fixed to On On-line Off-line Drawer kick-out connector pin 3 is LOW Drawer kick-out connector pin 3 is HIGH Not used. Fixed to Off Not used. Fixed to Off Page: 4-44 PA-3222 SERIES USER MANUAL...
  • Page 130 Black mark sensor status Not used. Fixed to Off Not used. Fixed to Off Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On Not used. Fixed to On PA-3222 SERIES USER MANUAL Page: 4-45...
  • Page 131 Selects Font B (9 x 17). GS h n [Name] Set bar code height. [Format] ASCII Hex. Decimal 104 n 1 ≤ n ≤ 255 [Range] Initial Value n = 162 [Description] Sets bar code height to n dots. Page: 4-46 PA-3222 SERIES USER MANUAL...
  • Page 132 48 ≤ d ≤ 57, 65 ≤ d ≤ 68, CODABAR 36, 43, 45, 46, 47, 58 1 ≤ n ≤ 255 0 ≤ d ≤ 127 CODE93 2 ≤ n ≤ 255 0 ≤ d ≤ 127 CODE128 PA-3222 SERIES USER MANUAL Page: 4-47...
  • Page 133 Paper roll near end detector Has Paper Paper out [Description] Drawer Kick Connector Status (n=2,50) “0” “1” Status Fixed at 0 Undefined Undefined Fixed at 0 Undefined Undefined Undefined “L” “H” Drawer kick connector pin Page: 4-48 PA-3222 SERIES USER MANUAL...
  • Page 134  xL and xH specify the horizontal direction data count for one bit image (xL + xH x 256) in bytes.  yL and yH specify the vertical direction data count for one bit image (yL + yH x 256) in bytes. [Description] PA-3222 SERIES USER MANUAL Page: 4-49...
  • Page 135 2 ≤ n ≤ 16 [Range] Initial Value n = 2 Specifies a module size of QR Code and Data Matrix. [Description] n: The number of dots for one side of the module size. Page: 4-50 PA-3222 SERIES USER MANUAL...
  • Page 136 Mode Numerical mode Alphanumeric mode 8-bit byte mode Kanji mode Mixed mode nl, nh: Specifies the number of data. Data: Kanji data of the QR Code data should be set by Shift JIS code. PA-3222 SERIES USER MANUAL Page: 4-51...
  • Page 137 Batch specifies the Kanji character print mode. “0” “1” Function Underline Undefined Undefined Undefined Double tall expanded Expanded wide Undefined Undefined FS & [Name] Select Kanji character mode. ASCII & [Format] Hex. Decimal [Range] [Description] Specifies Kanji character mode. Page: 4-52 PA-3222 SERIES USER MANUAL...
  • Page 138 Kanji character underlines. 2,50 Sets to two-dot width Kanji character underline and cancels Kanji character underlines. FS . [Name] Cancel Kanji character mode. ASCII [Format] Hex. Decimal [Range] [Description] Cancels Kanji character mode. PA-3222 SERIES USER MANUAL Page: 4-53...
  • Page 139 Specifies or cancels quadruple size Kanji character.  Cancels quadruple size when n = <*******0>B. [Description]  Specifies quadruple size when n = <*******1>B.  n is effective only when it is the lowest bit. Page: 4-54 PA-3222 SERIES USER MANUAL...

  • Page 140: Opos Printer Driver

    Follow the wizard instructions to complete the installation. Launching the Program Follow the steps below to load the MB1030 program: • Click the POSPrinter folder from the path: Start\Programs\Protech OPOS. • Click MB1030 to launch the program. PA-3222 SERIES USER MANUAL Page: 4-55...
  • Page 141 OPOS Control Object of MB1030 Program a.) Print tab buttons: Button/Item Description Printer Normal Print the string. b.) Bitmap tab buttons/items: Button/Item Description Load Load bitmap file. Print Bitmap Print bitmap file. Normal or Rotate 108˚. Type Page: 4-56 PA-3222 SERIES USER MANUAL...
  • Page 142 Default Value Note BaudRate String 115200 UART Baud Rate (default) BitLength String UART Data Bit (default) Parity String UART Parity Bit (default) Port String COM4 UART Port (default) Stop String UART Stop Bit (default) PA-3222 SERIES USER MANUAL Page: 4-57...
  • Page 143 Not Applicable Properties specific long CapJrnDhigh Read only Not Applicable Properties specific long CapJrnDwide Read only Not Applicable Properties specific long CapJrnDwideDhigh Read only Not Applicable Properties specific long CapJrnEmptySensor Read only Not Applicable Page: 4-58 PA-3222 SERIES USER MANUAL...
  • Page 144 CapSlpNearEndSensor Read only Not Applicable Properties specific bool CapSlpRight90 Read only Not Applicable Properties specific bool CapSlpRotate180 Read only Not Applicable Properties specific bool CapSlpUnderline Read only Not Applicable Properties specific bool AsyncMode Not Applicable PA-3222 SERIES USER MANUAL Page: 4-59...
  • Page 145 Properties specific bool JrnNearEnd Read only Not Applicable Properties specific long JrnCartridgeState Read only Not Applicable Properties specific long JrnCurrentCartridge Not Applicable Properties specific long RecLineChars Not Applicable Properties specific string RecLineCharsList Read only Not Applicable Page: 4-60 PA-3222 SERIES USER MANUAL...
  • Page 146 Claim Supported Methods common ClaimDevice Supported Methods common Release Supported Methods common ReleaseDevice Supported Methods common CheckHealth Supported Methods common ClearInput Not Applicable Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable PA-3222 SERIES USER MANUAL Page: 4-61...
  • Page 147 Not Applicable Methods specific MarkFeed Not Applicable Events common DataEvent Not Applicable Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputComplete Not Applicable Event Events common StatusUpdate Not Applicable Event Page: 4-62 PA-3222 SERIES USER MANUAL...

  • Page 148: Vfd: Mb-4103 (Rs-232)

    Parity Port COM1 Stop OPOS VFD Service Object and Method Relations Method Status of Support Notes ○ Open ○ Close ○ ClaimDevice ○ ReleaseDevice ○ Enable ○ Disable ○ DisplayText ○ DisplayTextAt ○ ClearText PA-3222 SERIES USER MANUAL Page: 4-63...

  • Page 149: Opos Driver

    Follow the onscreen wizard instructions to complete the installation. Launching the Program The steps below guide you to load the Prox-PMP4000 program: • Click the LineDisplay folder from the path: Start/Programs/Protech OPOS. • Click Prox-PMP4000 to launch the program. Page: 4-64 PA-3222 SERIES USER MANUAL...
  • Page 150 Default Value Note BaudRate String 9600 UART Baud Rate (default) BitLength String UART Data Bit (default) Parity String UART Parity Bit (default) Port String COM1 UART Port (default) Stop String UART Stop Bit (default) PA-3222 SERIES USER MANUAL Page: 4-65...
  • Page 151 Read only Not Applicable Properties specific long CapReverse Read only Not Applicable Properties specific bool CapVMarquee Read only Not Applicable Properties specific long BlinkRate Not Applicable Properties specific long DeviceWindows Read only Not Applicable Page: 4-66 PA-3222 SERIES USER MANUAL...
  • Page 152 Not Applicable Methods common DirectIO Not Applicable Methods specific DisplayText Supported Methods specific DisplayTextAt Supported Methods specific ClearText Supported Methods specific ScrollText Not Applicable Methods specific SetDescriptor Not Applicable Methods specific ClearDescriptors Not Applicable PA-3222 SERIES USER MANUAL Page: 4-67...
  • Page 153 Not Applicable Methods specific DefineGlyph Not Applicable Events common DataEvent Not Applicable Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable OutputComplete Events common Not Applicable Event StatusUpdate Events common Not Applicable Event Page: 4-68 PA-3222 SERIES USER MANUAL...

  • Page 154: Msr: Mb-3102 (Ps/2)

    The steps below guide you to load the Prox-PMP3000 program. • Click the MSR folder from the path: Start/Programs/Protech OPOS. • Click Prox-PMP3000 to launch the program. Configuration of Prox-PMP3000 program a.) Main screen & Control tab items: PA-3222 SERIES USER MANUAL Page: 4-69...
  • Page 155 (only for UART/USB interface). AutoDisable (check box) Check to disable the device automatically when data is received. FreezeEvents (check box) Enable to trigger FreezeEvents, and the application will not allow events to be delivered. Page: 4-70 PA-3222 SERIES USER MANUAL...
  • Page 156 Set decode data properties applicable. ParseDecodeData Set parse decode data properties TransmitSentinels Set transmit-sentinels properties ErrorReporting Type Card, track TracksToRead Track1, track2, track3, tracks12, tracks13, tracks14, tracks23, tracks24, tracks34, tracks123, tracks124, tracks134, tracks234, tracks1234 (Tracks4 is not applicable). PA-3222 SERIES USER MANUAL Page: 4-71...
  • Page 157 Chapter 4 Software Utilities d.) Track Data tab items Button/Item Description TracksData (Row) Display the data of all tracks (Track4 is not applicable). e.) Parsed Data tab items Button/Item Description Parsed Data Display special properties. Page: 4-72 PA-3222 SERIES USER MANUAL...
  • Page 158 Properties specific bool CapTransmitSentinels Read only Supported Properties specific long TracksToRead Supported Properties specific bool DecodeData Not Applicable Properties specific bool ParseDecodeData Supported Properties specific long ErrorReportType Not Applicable Properties specific string Track1Data Read only Supported PA-3222 SERIES USER MANUAL Page: 4-73...
  • Page 159 Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable Events common DataEvent Supported Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputCompleteEvent Not Applicable Events common StatusUpdateEvent Not Applicable Page: 4-74 PA-3222 SERIES USER MANUAL...

  • Page 160: Commands List

    Device Name for CO open FileName (NULL) (reserved) HardwareProvider (reserved) Model MJR243 Device model name Parity None Parity for the communication port Port COM4 COM Port Protocol Hardware Communication Control Baudrate 19200 RS-232 baudrate PA-3222 SERIES USER MANUAL Page: 4-75...
  • Page 161 ○ FirstName Read only ○ MiddleInitial Read Only ○ ParseDecodeData ○ ServiceCode Read Only ○ Suffix Read Only ○ Surname Read Only ○ Title Read Only ○ Track1Data Read Only ○ Track1DiscretionaryData Read Only Page: 4-76 PA-3222 SERIES USER MANUAL...

  • Page 162: Opos Msr Register

    Launching the Program The steps below guides you how to load the OPOS MSR Register program. • Click the OPOS folder from the path: Start/Programs/GIGA‐TMS. • Click OPOS MSR Register to launch the program. PA-3222 SERIES USER MANUAL Page: 4-77...
  • Page 163 Chapter 4 Software Utilities Page: 4-78 PA-3222 SERIES USER MANUAL...
  • Page 164 Step 1: Select an item in the Service Object List box from the left pane. Make sure the correct item is selected. Step 2: Click Reg button Step 3: In the OPOS MSR Setting screen, enter the device name and click PA-3222 SERIES USER MANUAL Page: 4-79...
  • Page 165 Chapter 4 Software Utilities c.) Example 1. MAGTEK USB HID d.) Example 2. PROMAG MSR/MJR PART‐ NO, Keyboard mode. Page: 4-80 PA-3222 SERIES USER MANUAL...
  • Page 166 Description for SO driver MSR POS DeviceName string MJR243 Device Name for CO open FileName string (NULL) (reserved) HardwareProvider string (reserved) Model string MJR243 Device model name Parity string None Parity for the communication port PA-3222 SERIES USER MANUAL Page: 4-81...
  • Page 167 Read only Supported string Properties specific bool CapISO Read only Supported Properties specific bool CapJISOne Read only Not Applicable Properties specific bool CapJISTwo Read only Not Applicable Properties specific bool CapTransmit Read only Supported Page: 4-82 PA-3222 SERIES USER MANUAL...
  • Page 168 Methods common ReleaseDevice Supported Methods common CheckHealth Not Applicable Methods common ClearInput Supported Methods common ClearInput Supported Properties Methods common ClearOutput Not Applicable Methods common DirectIO Not Applicable Methods common Compare Not Applicable FirmwareVersion PA-3222 SERIES USER MANUAL Page: 4-83...
  • Page 169 Methods common UpdateFirmware Not Applicable Methods common UpdateStatistics Not Applicable Events common DataEvent Supported Events common DirectIOEvent Not Applicable Events common ErrorEvent Not Applicable Events common OutputCompleteEvent Not Applicable Events common StatusUpdateEvent Not Applicable Page: 4-84 PA-3222 SERIES USER MANUAL...

  • Page 170: Opos Msr Tester

    Launching the Program The steps below guide you to load the OPOS MSR Tester program. • ‐ Click the OPOS folder from the path: Start\Programs\GIGA TMS. • Click OPOS MSR Tester to launch the program. PA-3222 SERIES USER MANUAL Page: 4-85...
  • Page 171 To get the track data using OPOS driver, follow the steps below: Step 1: Enter the Device Name. Step 2: Click Open button. Step 3: Swipe the card to get the track data. Page: 4-86 PA-3222 SERIES USER MANUAL...
  • Page 172 Chapter 4 Software Utilities c.) Example 1. MAGTEK USB HID. d.) Example 2. PROMAG MSR/MJR PART‐ NO, Keyboard mode PA-3222 SERIES USER MANUAL Page: 4-87...
  • Page 173 Chapter 4 Software Utilities e.) Example 3. PROMAG MSR PART‐ NO, HID mode Page: 4-88 PA-3222 SERIES USER MANUAL...

  • Page 174: Api Package Content

    Contents / File Name Description DEMO PROJECT\GPIO Sample C# VB6 VB.net Source Code DEMO Code PROJECT\ DEMO PROJECT\Digital C# VB6 VB.net Source Code Sample Code DEMO PROJECT\Watchdog C# VB6 VB.net MFC Source Sample Code Code PA-3222 SERIES USER MANUAL Page: 4-89...

  • Page 175: Api Procedure

    End if ‘========================================= Receive_Status2 = CashDrawerOpen(&H2) If Receive_Status2 = true then Text2.text = “cash drawer2 open” ‘enter text into textbox. Else Text2.text = “cash drawer2 close” ‘enter text into textbox. End if ‘========================================= End sub Page: 4-90 PA-3222 SERIES USER MANUAL...
  • Page 176 Public static extern bool GetCashDrawerStatus() [DllImport(“CashDrawer.dll”,EntryPoint = “CashDrawerOpen”)] Public static extern bool CashDrawerOpen(short num_drawer);} (2) Call Function Open cash drawer1 PortAccess.CashDrawerOpen(0x01); //check cash drawer1 status Open cash drawer2 PortAccess.CashDrawerOpen(0x02); //check cash drawer2 status Bool bstatus; bstatus = PortAccess.GetCashDrawerStatus(0x01); PA-3222 SERIES USER MANUAL Page: 4-91...
  • Page 177 As Boolean VB 6 external function: Declare Function CashDrawerOpen Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Declare Function GetCashDrawerStatus Lib "CashDrawer.dll" (ByVal num_drawer As Integer) As Boolean Note: VB.net short = integer VB6 Page: 4-92 PA-3222 SERIES USER MANUAL...

  • Page 178: Cash Drawer

    Cash Drawer Status Cash drawer status will be displayed after OPEN is tapped. • Cash Drawer is closed when the following picture is shown: • Cash Drawer is opened when the following picture is shown: PA-3222 SERIES USER MANUAL Page: 4-93...

  • Page 179: Watchdog

    • START: Tap to start the watchdog timer. Meanwhile, the REFRESH and STOP buttons will be enabled. • STOP: Tap to stop the watchdog timer. • REFRESH: Tap to restart the watchdog timer. Page: 4-94 PA-3222 SERIES USER MANUAL...

  • Page 180: Api Function

    = 1 (Get the Cash Drawer1 status) num_drawer = 2 (Get the Cash Drawer2 status) Return: True (1) on success, False (0) on failure Example: Short data; data= GetCashDrawerStatus(0x01); // Get the Cash Drawer1 status PA-3222 SERIES USER MANUAL Page: 4-95...

  • Page 181: Watch Dog Function

    Stop the watchdog timer Value None Return: True (1) on success, False (0) on failure Watchdog_Recount bool Watchdog_Recount (void); Purpose: Restart the watchdog timer Value None Return: True (1) on success, False (0) on failure Page: 4-96 PA-3222 SERIES USER MANUAL...

  • Page 182: Bios Setup

    The BIOS Setup Utilities consist of the following menu items: • Accessing Setup Utilities • Main Menu • Advanced Menu • Chipset Menu • Security Menu • Boot Menu • Save & Exit Menu PA-3222 SERIES USER MANUAL Page: 5-1...

  • Page 183: Introduction

    Chapter 5 BIOS Setup 5.1 Introduction The PA-3222 System uses an AMI (American Megatrends Incorporated) Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the built-in BIOS setup program, Power-On Self-Test (POST), PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.

  • Page 184: Accessing Setup Utility

    All the menu settings are described in details in this chapter. 5.2 Accessing Setup Utility After the system is powered on, BIOS will enter the Power-On Self-Test (POST) routines and the POST message will be displayed: PA-3222 SERIES USER MANUAL Page: 5-3...
  • Page 185 Chapter 5 BIOS Setup Figure 5-2. POST Screen with AMI Logo Press <Del> or <Esc> to access the Setup Utility program and the Main menu of the Aptio Setup Utility will appear on the screen as below: PA-3222 SERIES USER MANUAL Page: 5-4...
  • Page 186 US English. You may use <↑> or <↓> key to select among the items and press <Enter> to confirm and enter the sub-menu. The following table provides the list of the navigation keys that you can use while operating the BIOS setup menu. PA-3222 SERIES USER MANUAL Page: 5-5...
  • Page 187 The CMOS battery The battery may be losing power and users is bad or has been should replace the battery immediately. Also, recently replaced. this message is displayed once the new battery is replaced. PA-3222 SERIES USER MANUAL Page: 5-6...

  • Page 188: Main

    Displays the date that the current BIOS Time version is built. Sec RC Version No changeable options Displays the current Sec RC version. TXE FW Version No changeable options Displays the current TXE Version PA-3222 SERIES USER MANUAL Page: 5-7...
  • Page 189 The “Day” is automatically changed. System Time Hour, minute, second Sets the system time. The format is [Hour: Minute: Second]. Users can directly enter values or use <+> or <-> arrow keys to increase/decrease it. PA-3222 SERIES USER MANUAL Page: 5-8...

  • Page 190: Advanced

    CPU Configuration Sub-Menu CPU Configuration. Parameters. IDE Configuration Sub-Menu SATA Configuration Parameters. OS Selection Sub-Menu OS Selection Configures Option ROM execution, boot CSM Configuration Sub-Menu options filters, etc. USB Configuration Sub-Menu USB Configuration Parameters. PA-3222 SERIES USER MANUAL Page: 5-9...

  • Page 191: Advanced – Acpi Settings

    Configuration and Power Management Interface) settings, such as Enable Hibernation. ACPI Settings Screen BIOS Setting Options Description/Purpose Enable - Disabled Enables or Disables System ability to Hibernation - Enabled Hibernate (OS/S4 Sleep State). This option may be not effective with some PA-3222 SERIES USER MANUAL Page: 5-10...

  • Page 192: Advanced – F81866 Super Io Configuration

    Sets the parameters of Serial Port 4 Serial Port 4 Configuration Sub-menu (COMD). Sets Parameters of Parallel Port Parallel Port Configuration Sub-menu ( LPT/LPTE). - Cash Drawer 12V Cash drawer Cash Drawer select 12V or 24V. - Cash Drawer 24V PA-3222 SERIES USER MANUAL Page: 5-11...
  • Page 193 - IO=3F8h; IRQ=4; settings for the Serial Port 1. - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; COM1 Voltage - Disabled Disables or selects COM1 select - 12V Voltage 12V/5V. - 5V PA-3222 SERIES USER MANUAL Page: 5-12...
  • Page 194 Serial Port 2. Change Settings - Auto Selects IRQ and I/O resource - IO=2F8h; IRQ=3; settings for the Serial Port 2. - IO=3F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; PA-3222 SERIES USER MANUAL Page: 5-13...
  • Page 195 Serial Port 3. Change Settings - Auto Selects IRQ and I/O resource - IO=3E8h; IRQ=7; settings for the Serial Port 3. - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F0h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12; PA-3222 SERIES USER MANUAL Page: 5-14...
  • Page 196 - IO=2E8h; IRQ=10; settings for the Serial Port 4. - IO=3E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E8h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2F0h; IRQ=3,4,5,6,7,9,10,11,12; - IO=2E0h; IRQ=3,4,5,6,7,9,10,11,12; - Disabled Disables or selects COM4 COM4 Voltage - 12V Voltage 12V/5V. select - 5V PA-3222 SERIES USER MANUAL Page: 5-15...
  • Page 197 Changes the printer port - SPP Mode mode. - EPP-1.9 and SPP Mode Mode - EPP-1.7 and SPP Mode - ECP Mode - ECP and EPP 1.9 Mode - ECP and EPP 1.7 Mode PA-3222 SERIES USER MANUAL Page: 5-16...

  • Page 198: Advanced – Hardware Monitor

    No changeable options Detects and displays 12V voltage. VCC3V No changeable options Detects and displays 3V voltage. VSB3V No changeable options Detects and displays VSB3V voltage. Detects and displays the battery VBAT No changeable options voltage. PA-3222 SERIES USER MANUAL Page: 5-17...

  • Page 199: Advanced – F81866 Watchdog Configuration

    Selects 1s (second) or 60s (minute) as Watchdog timer unit - 60s the time unit of Watchdog timer. Count for Timer Numeric (from 1 to Sets the timeout for Watchdog timer. (Seconds) 255) (Max. value: 255 seconds or minutes) PA-3222 SERIES USER MANUAL Page: 5-18...

  • Page 200: Advanced – Cpu Configuration

    BIOS Setting Options Description/Purpose Socket 0 Sub-Menu Reports CPU Information CPU Information CPU Speed No changeable options Displays the CPU speed. Reports if the processor supports Intel 64-bit No changeable options x86-64 (amd64) implementation. PA-3222 SERIES USER MANUAL Page: 5-19...
  • Page 201 Intel HT Technology No changeable options Reports if Intel Hyper-Threading Technology is supported by processor. Hyper Threading is Intel’s term for its simultaneous multithreading implementation in their CPUs. Enable this function will improve parallelization of PA-3222 SERIES USER MANUAL Page: 5-20...
  • Page 202 L1 Code Cache No changeable options Displays the size of L1 Code Cache. L2 Cache No changeable options Displays the size of L2 Cache. L3 Cache No changeable options Displays the size of L3 Cache. PA-3222 SERIES USER MANUAL Page: 5-21...

  • Page 203: Advanced – Ide Configuration (Ahci Mode)

    SATA Speed Support - GEN2 Gen2 mode sets the device to 3 Gbit/s speed (in case it is compatible). - Port0 ODD SATA ODD Port SATA ODD is Port0 or Port1 - Port1 ODD PA-3222 SERIES USER MANUAL Page: 5-22...
  • Page 204 SATA Port 0 [drive] SATA port 0. Shows [Empty] if no drive is installed. Displays the drive installed on the SATA Port 1 [drive] SATA port 1. Shows [Empty] if no drive is installed. PA-3222 SERIES USER MANUAL Page: 5-23...

  • Page 205: Advanced – Os Selection

    The OS Selection allows users to select the operating system from Windows 7 or Windows 8.x &10. OS Selection Screen BIOS Setting Options Description/Purpose - Windows 7 OS Selection OS Selection - Windows 8.x & 10 PA-3222 SERIES USER MANUAL Page: 5-24...

  • Page 206: Advanced – Csm Configuration

    ALWAYS: Do not allow disabling GA20; this option is useful when any RT code is executed above 1MB. Option ROM - Force BIOS Configures the display mode for Option Messages - Keep Current ROM messages. PA-3222 SERIES USER MANUAL Page: 5-25...
  • Page 207 Controls the execution of UEFI and Video - UEFI Legacy Video. - Legacy - Do not launch Selects launch method for other PCI Other PCI devices - UEFI devices, such as NIC, mass storage or - Legacy video card. PA-3222 SERIES USER MANUAL Page: 5-26...

  • Page 208: Advanced – Usb Configuration

    USB Mass Storage Driver - Disabled Enable/Disable USB mass storage driver Support - Enabled support. The time-out value for Control, Bulk, and USB transfer time-out 1 / 5 / 10 /20 sec Interrupt transfers. PA-3222 SERIES USER MANUAL Page: 5-27...

  • Page 209: Chipset

    Delay range is from 1 to 40 seconds, in ranging from 0 to seconds one second increments 5.5 Chipset Menu Path Chipset This menu allows users to configure advanced Chipset settings such as North Bridge and South Bridge configuration parameters. Chipset Screen PA-3222 SERIES USER MANUAL Page: 5-28...

  • Page 210: North Bridge

    Displays the DRAM information on Memory Information No changeable options the platform. Total Memory No changeable options Displays the DRAM size Memory Slot0 No changeable options Memory in the slot 0. PA-3222 SERIES USER MANUAL Page: 5-29...

  • Page 211: North Bridge – Lcd Control

    The LCD Control allows users to select the primary and secondary display device. LCD Control Screen BIOS Setting Options Description/Purpose Primary IGFX Boot - CRT Select Primary Display Device Display - LVDS - Disabled Secondary IGFX - CRT Select Secondary Display Device Boot Display - LVDS PA-3222 SERIES USER MANUAL Page: 5-30...

  • Page 212: South Bridge

    • Power On keeps the system powered on after the system restores AC power to the board. • Last State brings the system back to the last power state when the AC power is removed. PA-3222 SERIES USER MANUAL Page: 5-31...

  • Page 213: Security

    Setup utility. Security Screen BIOS Setting Options Description/Purpose Password can be 3-20 Specifies the administrator Administrator Password alphanumeric characters. password. Password can be 3-20 User Password Specifies the user password. alphanumeric characters. PA-3222 SERIES USER MANUAL Page: 5-32...

  • Page 214: Boot

    Specifies the power-on state of the Bootup NumLock State - Off NumLock Key. - Disabled Enable or Disable Quiet Boot Quiet Boot - Enabled Options - Disabled Fast Boot Enable or Disable Fast Boot Options - Enabled PA-3222 SERIES USER MANUAL Page: 5-33...

  • Page 215: Boot – Hard Drive Bbs Priorities

    Select Hard Drive BBS Priorities from the Boot menu to configure the boot order and priority of the available drives. Hard Drive BBS Priorities Screen BIOS Setting Options Description/Purpose - [Drive(s)] Set the system boot order for hard Boot Option #1~#n - Enabled driver. PA-3222 SERIES USER MANUAL Page: 5-34...

  • Page 216: Save & Exit

    Discard Changes and Reset to discard any changes you have made and restore the factory BIOS defaults. Load User Defaults You may simply press F3 at any time to load the Optimized Values which resets all BIOS settings to the factory defaults. Save & Exit Screen PA-3222 SERIES USER MANUAL Page: 5-35...
  • Page 217 Save the changes done so far as User Save as User Defaults No changeable options Defaults. Restore the User Defaults to all the Restore User Defaults No changeable options setup options. Forces to boot from selected Boot Override - [Drive(s)] [drive(s)]. PA-3222 SERIES USER MANUAL Page: 5-36...

  • Page 218: Appendix A System Diagrams

    Appendix A System Diagrams This appendix presents the exploded diagrams of the system as well as the part numbers of the PA-3222 system.  Exploded Diagram for System Top Case  Exploded Diagram for System  Exploded Diagrams for System LCD Panel ...

  • Page 219: Exploded Diagram For System Top Case

    PA-322_VFD_Unit See Page A-16 M3_L4_I_B 22-272-30004318 PA-3222_TOP Unit See Page A-5~A-6 M6 Stand 22-289-60035007 Rubber Foot(S1608) 30-004-01500000 mini_pcie_door(Black) 30-007-28110165 PA-3100 Side DOOR(Black) 30-007-28210165 PA-3100_Printer_Unit See Page A-11~A-14 PS-3100 I/O Cable Cover(Black) 30-002-28110165 Lens(HHP-4F) 30-012-02100000 PA-3222 SERIES USER MANUAL Page: A-2...

  • Page 220: System Exploded Diagram

    Appendix A System Diagrams System Exploded Diagram Page: A-3 PA-3222 SERIES USER MANUAL...
  • Page 221 Appendix A System Diagrams PA-3222 SERIES USER MANUAL Page: A-4...

  • Page 222: Exploded Diagrams For System Lcd Panel

    Appendix A System Diagrams Exploded Diagrams For System LCD Panel With MSR and RFID Modules 80 63 65 73 Page: A-5 PA-3222 SERIES USER MANUAL...

  • Page 223: Exploded Diagrams For System Lcd Panel

    124 M2_L2.5_R_Ni 22-222-20004011 125 LCD_Tape_110x5x2.2 34-026-06101400 126 LCD_Tape_90x10x2.2 34-026-06103400 127 LCD_Tape_70x10x2.2 34-026-06102400 128 61x22_Tape 94-034-04902400 129 LCD PORON 90-013-24200304 130 LCD PORON 90-013-24200304 131 M3_L7_W_Ni 22-232-30007011 132 cable_tipe 90-015-04100000 133 double-sided_tape_52x4.5x0.25 34-026-04901400 134 i-button_IBT200MX 52-551-00100002 PA-3222 SERIES USER MANUAL Page: A-6...

  • Page 224: Exploded Diagrams For System Lcd Panel

    Appendix A System Diagrams Exploded Diagrams For System LCD Panel With MSR and i-Button Modules Page: A-7 PA-3222 SERIES USER MANUAL...

  • Page 225: Exploded Diagram For Hdd

    Appendix A System Diagrams Exploded Diagram For HDD Q’TY COMPONENT NAME PART NO. REMARK 2inch_SATA_HDD See Order PA-3222 HDD Holder 80-029-03001400 Sata Cable 27-012-33903081 M3_L5_W_Ni 22-242-30005311 PA-3222 SERIES USER MANUAL Page: A-8...

  • Page 226: Exploded Diagram For Msr Module

    Appendix A System Diagrams Exploded Diagram For MSR Module COMPONENT NAME PART NO. Q’TY REMARK 139 ps3100_msr_holder.sldprt 20-029-03005165 140 MSR See Order 141 M3_L6_F_B 22-215-30060011 142 PA-3222_msr_cable Page: A-9 PA-3222 SERIES USER MANUAL...

  • Page 227: Exploded Diagram For Fingerprint Module

    Appendix A System Diagrams Exploded Diagram For Fingerprint Module PA-3222 SERIES USER MANUAL Page: A-10...

  • Page 228: Exploded Diagram For 3-Inch Printer (1)

    156 EMI_GASKET_20X5x0.5 90-050-31200165 157 ps3100_paper_cover_Unit See Next Page 158 M3_L5_W_Ni 22-242-30005311 159 paper_cover_pin 20-004-10011165 160 ps3100-spring-1 23-002-00000701 161 pg-13-270p 30-022-09110000 162 printer_add_arm 30-002-09110165 163 M3_L4_I_B 22-272-30004318 164 printer_power_cable 27-012-16502071 165 PA-3222_printer_cable(USB) 27-006-40307111 166 MB-1011RB-11N MB-1011RB-11N Page: A-11 PA-3222 SERIES USER MANUAL...

  • Page 229: Exploded Diagram For 3-Inch Printer (2)

    3 Inch Printer Q’TY COMPONENT NAME PART NO. REMARK paper_holder2.sldprt 30-012-02110165 T2_L8_R_B 22-125-20008011 ps3100_paper_cover_v2 30-002-02530165 include_holder 20-029-03006165 ps3100_printer_cover_ejector 30-002-09210165 ps3100-spring-for_ejector 23-002-00001021 M3_L4_I_B 22-272-30004318 T3_L6_PAN_NI 22-132-30060011 3100_printer_eva 90-013-15200165 3intch_add_mylar 90-056-02600165 3" Thermal Printer(Cut Side) T3_L8_R_B 22-122-30080011 PA-3222 SERIES USER MANUAL Page: A-12...

  • Page 230: Exploded Diagram For 2-Inch Printer (1)

    185 ps3100_paper_cover_Unit See Next Page 186 M3_L5_W_Ni 22-242-30005311 187 paper_cover_pin 20-004-10011165 188 ps3100-spring-1 23-002-00000701 189 pg-13-270p 30-022-09110000 190 printer_add_arm 30-002-09110165 191 M3_L4_I_B 22-272-30004318 192 add_paper_wall 30-002-28310165 193 printer_power_cable 27-012-16502071 194 PA-3222_printer_cable(USB) 27-006-40307111 195 MB-1011RB-11N MB-1011RB-11N PA-3222 SERIES USER MANUAL Page: A-13...

  • Page 231: Exploded Diagram For 2-Inch Printer (2)

    2 Inch Printer Q’TY COMPONENT NAME PART NO. REMARK paper_holder2.sldprt 30-012-02110165 T2_L8_R_B 22-125-20008011 ps3100_paper_cover_v2 30-002-02530165 include_holder 20-029-03006165 ps3100_printer_cover_ejector 30-002-09210165 ps3100-spring-for_ejector 23-002-00001021 M3_L4_I_B 22-272-30004318 T3_L6_PAN_NI 22-132-30060011 3100_printer_eva 90-013-15200165 2intch_add_mylar2 90-056-02300165 2" Thermal Printer(Cut Side) T3_L8_R_B 22-122-30080011 PA-3222 SERIES USER MANUAL Page: A-14...
  • Page 232 Appendix A System Diagrams With Paper Holder Without Paper Holder Page: A-15 PA-3222 SERIES USER MANUAL...

  • Page 233: Exploded Diagram For Vfd Module

    Appendix A System Diagrams Exploded Diagram For VFD Module Q’TY COMPONENT NAME PART NO. REMARK 208 ps3100_vfd_cover 30-002-28114165 209 ps3100_vfd_window 30-002-02230165 210 VFD_Model MB-4103RA-11N 211 PORON_135x4x0.5 90-013-24100165 212 PA-3222_VFD_CABLE 27-053-23805111 PA-3222 SERIES USER MANUAL Page: A-16...

  • Page 234: Appendix B Technical Summary

    This appendix will give you a brief introduction of the allocation maps for the system resources. The following topics are included: • Interrupt Map • DMA Channels Map • I/O Map • Memory Map • Configuring WatchDog Timer • Flash BIOS Update Page: B-1 PA-3222 SERIES USER MANUAL...

  • Page 235: Interrupt Map

    IRQ 93 Microsoft ACPI-Compliant System IRQ 94 Microsoft ACPI-Compliant System IRQ 95 Microsoft ACPI-Compliant System IRQ 96 Microsoft ACPI-Compliant System IRQ 97 Microsoft ACPI-Compliant System IRQ 98 Microsoft ACPI-Compliant System IRQ 99 Microsoft ACPI-Compliant System PA-3222 SERIES USER MANUAL Page: B-2...
  • Page 236 IRQ 134 Microsoft ACPI-Compliant System IRQ 135 Microsoft ACPI-Compliant System IRQ 136 Microsoft ACPI-Compliant System IRQ 137 Microsoft ACPI-Compliant System IRQ 138 Microsoft ACPI-Compliant System IRQ 139 Microsoft ACPI-Compliant System IRQ 140 Microsoft ACPI-Compliant System PA-3222 SERIES USER MANUAL Page: B-3...
  • Page 237 IRQ 175 Microsoft ACPI-Compliant System IRQ 176 Microsoft ACPI-Compliant System IRQ 177 Microsoft ACPI-Compliant System IRQ 178 Microsoft ACPI-Compliant System IRQ 179 Microsoft ACPI-Compliant System IRQ 180 Microsoft ACPI-Compliant System IRQ 181 Microsoft ACPI-Compliant System PA-3222 SERIES USER MANUAL Page: B-4...
  • Page 238 Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 Note: These resource information were gathered using Windows 7 (the IRQ could be assigned differently depending on OS) DMA MAP ASSIGNMENT Channel 3 Printer Port (LPT1) PA-3222 SERIES USER MANUAL Page: B-5...
  • Page 239 Motherboard resources 0x000000B4-0x000000B5 Programmable interrupt controller 0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000002E8-0x000002EF Communications Port (COM4) 0x000002F8-0x000002FF Communications Port (COM2) 0x00000378-0x0000037F Printer Port (LPT1) 0x000003B0-0x000003BB Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 PA-3222 SERIES USER MANUAL Page: B-6...
  • Page 240 Processor AHCI - 0F23 0x0000F050-0x0000F057 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F060-0x0000F063 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F070-0x0000F077 Intel(R) Atom(TM)/Celeron(R)/Pentium(R) Processor AHCI - 0F23 0x0000F080-0x0000F087 Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0x00000000-0x0000006F PCI bus PA-3222 SERIES USER MANUAL Page: B-7...

  • Page 241: Memory Map

    0F12 0xD0500000-0xD05FFFFF Intel(R) Trusted Execution Engine Interface 0xD0400000-0xD04FFFFF Intel(R) Trusted Execution Engine Interface 0xA0000-0xBFFFF Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xA0000-0xBFFFF PCI bus 0xC0000-0xDFFFF PCI bus 0xE0000-0xFFFFF PCI bus 0xD0600000-0xD06FFFFF Intel(R) Atom(TM)/Celeron(R)/Pentium(R) PA-3222 SERIES USER MANUAL Page: B-8...
  • Page 242 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xC0000000-0xCFFFFFFF Intel(R) Atom(TM) Processor E3800 Series/Intel(R) Celeron(R) Processor N2920/J1900 0xC0000000-0xCFFFFFFF PCI bus 0xFED00000-0xFED003FF High precision event timer 0xD0604000-0xD0604FFF Realtek PCIe GBE Family Controller 0xD0700000-0xD070FFFF Intel(R) USB 3.0 eXtensible Host Controller PA-3222 SERIES USER MANUAL Page: B-9...
  • Page 243 To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. PA-3222 SERIES USER MANUAL Page: B-10...
  • Page 244 ; ----------------------- Select Logical Device 7 of watchdog timer --------------------- dx, al dx, al ;---------------------------------Enable Watch dog feature ------------------------------ 030h dx, al dx, al ;------------------------------- Enable Watch PME-------------------------------------------- 0FAh dx, al dx, al ;-------------------------- Set second as counting unit -------------------------------------- 0F5h dx, al PA-3222 SERIES USER MANUAL Page: B-11...
  • Page 245 Appendix B Technical Summary dx, al ; ---------------- Set timeout interval as 30seconds and start counting -------------- 0F6h dx, al dx, al ;---------------------------------Exit the extended function mode ------------------------- 0AAh dx, al PA-3222 SERIES USER MANUAL Page: B-12...
  • Page 246 (4) Select [Boot] menu. (5) Select [Hard Drive BBS Priorities] and set the USB bootable device as the 1st boot device. (6) Press F4 to save the configuration and exit the BIOS setup menu. PA-3222 SERIES USER MANUAL Page: B-13...
  • Page 247 Appendix B Technical Summary PA-3222 SERIES USER MANUAL Page: B-14...
  • Page 248 BIOS ROM may be crashed and the system will be unable to boot up next time. After the BIOS update procedure is completed, the following messages will be shown: PA-3222 SERIES USER MANUAL Page: B-15...
  • Page 249 5. Restart the system and boot up with the new BIOS configurations. 6. The BIOS Update is completed after the system is restarted. 7. Reboot the system and verify if the BIOS version shown on the initialization screen has been updated. PA-3222 SERIES USER MANUAL Page: B-16...

Table of Contents