Amp Envelope - Korg Liverpool Owner's Manual

120 Program operating mode
Page 16 - Amp EG

Amp envelope

Amplifier EG
Attack Level
Note-on
Volume
Start
Level
Attack Decay
Time Time
Start/Attack/Break/Sustain/Release Level
These parameters are the level of the envelope segment.
0...99 Level value.
Start Level
This parameter specifies the volume level at note-on. If
you want the note to begin at a loud level, set this to a
high value.
Attack Level
This parameter specifies the volume level that will be
reached after the attack time has elapsed.
Break Level
This parameter specifies the volume level that will be
reached after the decay time has elapsed.
Sustain Level
This parameter specifies the volume level that will be
maintained from after the slope time has elapsed until
note-off occurs.
Attack/Decay/Slope/Release Time
These parameters specify the time over which the vol-
ume change will occur.
0...99 Time value.
Attack Time
This parameter specifies the time over which the volume
will change after note-on until it reaches the attack level.
If the start level is 0, this will be the rise time of the sound.
Decay Time
This parameter specifies the time over which the vol-
ume will change from when it reaches the attack level
until it reaches the break point level.
Slope Time
This parameter specifies the time over which the vol-
ume will change from when it reaches the break point
level until it reaches the sustain level.
Release Time
This parameter specifies the time over which the vol-
ume will change after note-off until it reaches 0.
Note-off
Break Point
Sustain
Level
Time
Slope Release Time
Time
Amp EG 'Level' modulation
Amp 1 EG changes (Level) (AMS=Velocity, Intensity = a positive (+) value)
Note-on Note-on
Note-off
Softly played note when Start Strongly played note when
Level Swing=0 and Attack Level Start Level Swing=0 and Attack
Swing and Breack Level Swing Level Swing and Breack Level
are set to + Swing are set to +
AMS(L) (Alternate Modulation Source)
This parameter specifies the source that will control the
"Level" parameters of the amp EG. See "AMS (Alter-
nate Modulation Source) list" on page 124.
Intensity
This parameter specifies the depth and direction of the
effect that "AMS" will have. For example, if "AMS" is
Velocity, setting "Start Level Swing", "Attack Level
Swing" and "Break Point Level Swing" to + and setting
"Intensity" to a positive (+) value will cause the amp
EG volume levels to increase as you play more
strongly. Setting "Intensity" to a negative (–) values
will cause the amp EG volume levels to decrease as you
play more strongly. With a setting of 0, the levels will
be as specified on "Page 16 - Amp EG".
-99...+99 Intensity value.
Start Level Swing
This parameter specifies the direction in which "AMS"
will change "Start Level". If "Intensity" is set to a posi-
tive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Attack Level Swing
This parameter specifies the direction in which "AMS"
will change "Attack Level". If "Intensity" is set to a pos-
itive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Break Point Level Swing
This parameter specifies the direction in which "AMS"
will change "Break Level". If "Intensity" is set to a pos-
itive (+) value, setting this parameter to + will allow
AMS to increase the EG level, and setting this parame-
ter to – will allow AMS to decrease the EG level. With a
setting of 0, no change will occur.
Note-on
Note-off Note-off
Strongly played note when
Start Level Swing=0 and Attack
Level Swing and Breack Level
Swing are set to +