Press Arm Support - BodyCraft GXP Assembly Instruction Manual

STEP 4 ASSEMBLE PRESS ARM AND SEAT & BACK PAD
1. Attach the Press Arm Support (9) to the Top Frame (2) by aligning the holes and inserting
the Axle (27). Secure the Axle (27) using two 1/2" Larger Washers (135), and two 1/2"
Nylon Nuts (144). Tighten these 1/2" Nylon Nuts (144) and then cap with two domed 1/2"
Cap Nuts (82). Attach the Press Arm (7) to the Press Arm Support (9) by aligning the
holes and inserting the Press Arm Axle (30). Make sure the Longer Pop Pin (100) is
inserted into one of the adjustment holes in the Press Arm Support (9). Secure the Press
Arm Axle (30) by tightening the pre-assembled 5/16" X 1/4" Set Screws (133). Attach the
Plastic Cover (58) to the front of the Press Arm Support (9) and secure using one M5 X 2-
1/2" Screw (127).
2. Attach Seat Back Adjuster (12) to Main Frame (1), using one 3/8" X 5-1/4" Hex Bolt (108),
four 3/8" Washers (137) and one 3/8" Nylon Nut (145). It may be necessary to tighten this
bolt, then loosen just enough to let Seat Back Adjuster (12) pivot FREELY. Longer Red
Pop Pin (100) should seat into adjustment holes in Seat Back Adjuster (12).
3. Attach Leg Holder (13) to Seat Back Adjuster (12), using two 5/16" X 1/2" Screws (117)
and two 5/16" Washers (138). Tighten these screws. Slide two Metal Hinges (14) holes at
bottom, onto the axle welded to top of the Seat Back Adjuster (12), then attach Back Pad
(52) to Metal Hinges (14), using two 3/8" X 1" Hex Threaded Bolts (112) and two 3/8"
Washers (137).
4. Attach Seat Pad (51) to Seat Adj. Handle (10), using two 3/8" X 1" Hex Threaded Bolts
(112) and two 3/8" Washers (137). Attach Seat Adj. Frame (11) to Seat Adj. Handle (10),
using two 3/8" X 1-3/4" Hex Threaded Bolts (110) and two 3/8" Washers (137).
5. Insert the Seat Spring (153) into the Seat Frame (4), then slide the Seat Adj. Frame (11)
over top the Seat Spring (153), and into the Seat Frame (4). Screw the Pop Pin attached
to the Longer Clutch Cable (71) into the receptor in the Seat Frame (4). If the Seat Spring
(153) interferes with this, you may need to rotate the spring a bit until it does not interfere.
6. Insert the 1" Foam Roller Holder (28) into the tube welded to the front of the Seat Adj.
Frame (11) and secure with the two 5/16" X 1/4" Set Screws (133). Slide a Plastic Cap
(83) onto each side of the 1" Foam Roller Holder (28), flat side to the outside. Slide a
Foam Pad (53) onto each side of the 1" Foam Roller Holder (28) then cap with an
Aluminum Cap (84) and secure with a 5/16" X 1-1/4" Screw (123).
7. Screw the Tighten Knob (102) into the threaded receptor in the Seat Frame (4). You can
use this Tighten Knob (102) to eliminate wobble in the seat after you have adjusted the
seat to the desired height.
8. Slide two Aluminum Caps (83) onto each inside of Leg Holder (13), flat side to outside.
Moisten Foam Pads (53) with water and slide onto the Leg Holder (13). Cover with an
Aluminum Cap (84) and secure with a 5/16" X 1-1/4" Screw (123).
9