Press Arm - BodyCraft X2 Instruction Manual

S
T E P 4
1. Attach Press Arm Selector(12) to Top Frame - bearing pre-installed(10) by aligning holes and inserting
1" Pivot Axle(33). Lock into place with pre-installed set screw.
2. Attach Press Arm(17) to Press Arm Selector(12) by aligning holes and inserting 1" Pivot Axle(33),
19.95mm Axle(33A). Lock into place with pre-installed set screw. Attach 50mm SQ. Plug(64) onto ends of
Press Arm(17) and Press Arm Selector(12).
3. Check Longer Pop Pin(77) into Press Arm Selector(12), making sure Pop Pin(77) seats into
adjustment holes in Press Arm(17).
4. Attach Leg Press Main Frame(46) to Leg Press to Weight Base Connector(51) and Long Leg Press
Connector(49), using two 3/8" X 4" Hex Bolts(127), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154).
5. Attach Base Stabilizer(2) to Leg Press Main Frame(46) using two 1/2" X 3" Hex Head Bolts(123) and
two 1/2" Nylon Nuts(153). Attach 45 X 75mm Rect. Cap(61) to rear of Leg Press Main Frame(46) and
two 50mm SQ. Caps(62) to Base Stabilizer(2).
6. Remove one Bearing Housing(56) from Leg Press Main Frame(46). Slide Axle on Rear Leg Press
Support(52) into each Bearing Housing(56), then attach Bearing Housing(56) back onto Leg Press
Main Frame(46). Attach Front Leg Press Support(50) to Leg Press Main Frame(46) using one 5/8" X 6-
1/2" Hex Head Bolt(121), two 5/8" Washers(145) and one 5/8" Nylon Nut(153).
7. Slide both Leg Press Axles(57) through pre-installed 1" Bushings(75) on Foot Plate Connector(53).
Attach Foot Plate Connector(53) to Rear Leg Press Support(52) and Front Leg Support(50) using one
each 5/8" X 6-1/2" Hex Head Bolt(121), two 5/8" Washers(145) and one 5/8" Nylon Nut(152).
8. Attach Foot Plate(54) to Foot Plate Connector(53), using two 1/2" Washers(146) and two 1/2" Nylon
Nuts(153). Attach 45 X 75mm Rect. Plugs(64) to Foot Plate(54). Attach Right and Left Leg Press
Handles(47, 48) to Leg Press Main Frame(46), angle facing up, using two 3/8" X 3" Hex Head Bolts
(128), four 3/8" Washers(147) and two 3/8" Nylon Nuts(154). Attach Seat Pad for Leg Press(107) to
Leg Press Main Frame(46), using two 3/8" Washers(147) and two 3/8" X 1" Hex Head Bolts(134), one
3/8" X 2-3/4" Hex Head Bolt(129). Attach Back Pad for Leg Press(106) to Back Pad Adjuster(55) using
two 3/8" Washers(147) and two 3/8" X 1" Hex Head Bolts(134). Slide Back Pad Adjuster(55) into Leg
Press Main Frame(46) by pulling pre-installed Locking Spring Knob(79).
Tighten all the bolts and nuts gradually, from ground - up.
33A
12
33
64
64
17
58
58
ASSE M BL E BE NC H PR E SS AND L E G PR E SS
64
140
10
140
49
127
147
146
153
121
63
145
52
50
127
147
121
56
145
62
153
51
123
2
10
106
107
63
53
54
63
153
89
128
147
48
71
145
152
147
129
147
134
56
147
46
154
145
152
153
62
134
147
65
55
147
134
79
71
61
47
147
147
154
89
154