Related Manuals for Eaton XV400 10.4"
Summary of Contents for Eaton XV400 10.4"
- Page 1 12/2010 MN04802010Z-EN Operating Instructions replaces M000630-13, 03/2010 XV400 10.4"/12.1"/15" MICRO PANEL...
- Page 2 All brand and product names are trademarks or registered trademarks of the owner concerned. Copyright © Eaton Automation AG, CH-9008 St. Gallen All rights reserved, also for the translation. None of this document may be reproduced or processed, duplicated or distributed by electronic systems in any form (print, photocopy, microfilm or any other process) without the written permission of Eaton Automation AG, St.
-
Page 3: Table Of Contents
Engineering conditions of acceptability by Underwriters Labaratories Inc. (UL) ..5.2.3 Requirements for the mounting position ..............Cable preparation......................5.3.1 Overview of interfaces....................5.3.2 Preparation of cables with D-Sub connector............... 5.3.3 Power supply....................... 5.3.4 RS232 (System Port) ....................MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 4 9.1.6 15" devices with 4-hole front ..................Display ........................Touch sensor ......................9.3.1 Devices with resistive touch ..................9.3.2 Devices with infra-red touch..................System ........................Interfaces ........................9.5.1 Power supply....................... Enclosure ratings ......................MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 5 Contents Agency approvals and standards................Applicable standards and regulations ................. Ambient conditions...................... MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 6 Contents MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 7: General
Additional documentation The following documents may be helpful in the use of the device in addition to this document. These can be downloaded from our home page (www.eaton-automation.com/en), «DOWNLOADS» section. [1] MN05010007Z-EN System Description Windows CE (operation of the Windows CE operating system on MICRO PANELs) - Page 8 1 General 1.3 Additional documentation MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 9: Device Description
XV-440-12TSB-1-2x MC2-440-12TSB-1-2x Infra-red touch 12.1", stainless steel front XV-440-12TSB-1-5x MC2-440-12TSB-1-5x Infra-red touch 15", standard front XV-460-15TXB-1-1x Infra-red touch 15", 4-hole front XV-460-15TXB-1-2x Infra-red touch 15", stainless steel front XV-460-15TXB-1-5x Tab. 1 Device versions MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 10 Fig. 1 XV400, MC2 with resistive touch and standard front Fig. 2 XV400, MC2 with infra-red touch and standard front Fig. 3 XV400, MC2 with infra-red touch and 4-hole front Fig. 4 XV400, MC2 with infra-red touch and stainless steel front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 11: Package Contents
Retaining brackets with threaded pin for mounting the device Sealing strip for mounting the device Power supply connector CF slot cover (fitted) Slot covers (fitted) Tab. 3 Package contents for 10.4" and 12.1" devices with infra-red touch and standard front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 12: Package Contents For Devices With 4-Hole Front
XV-460-15TXB-1-2x Countersunk screws for mounting the device Front seal for mounting the device Power supply connector CF slot cover (fitted) Slot covers (fitted) Tab. 5 Package contents for devices with 4-hole front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 13: Package Contents For Devices With Stainless Steel Front
Arrangement of interfaces and operating elements Support To ensure fast and optimum support always provide the support personnel with the following informa- tion on the nameplate: Part no. (Part-No or Art.-No) Serial no. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 14 2 Device description 2.7 Designation MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 15: Safety Regulations
Read this chapter before working with the device. This contains important information for your personal safety. This chapter must be read and understood by all persons work- ing with this device. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 16: Meaning Of Symbols
Signal word CAUTION without safety alert symbol Indicates a situation which, if not avoided, could result in material damage. Indicates useful information. The danger symbol used and the text indicate the actual danger and the related preventative measures. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 17: Mandatory Requirements, Personnel
It must be ensured that the device is properly connected, mounted, maintained and disposed of in compliance with all relevant standards and safety regulations. 3.3.5 Prohibited use The implementation of safety functions (relating to the protection of personnel and machinery) using the device is prohibited. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 18: Requirements For Proper Operation
Failure or malfunction of the device Improper handling or use Failure to observe the Operating Instructions Conversions, modifications and repairs to the device Repairs, see Chapter 7.3.1 Repairs, 62. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 19: Device Related Hazards
Avoid contact with components (such as connector pins) that are susceptible to electrostatic discharge. Discharge (by touching a grounded metal object) any static charge accumulated in your body before touching the device. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 20 Do not use any pointed or sharp objects (e.g. knife) for cleaning. Do not use any aggressive or abrasive cleaning agent or solvent. Avoid any liquid entering the device (risk of short-circuit). MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 21: Operating And Indication Elements
(min. ø 7 mm). It is not necessary to touch the infra-red touch protective panel. B Display Display operating and indication elements. Tab. 7 Operating and indication elements on the front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 22: Operating Elements On The Service Side
Slot for CF card with operating system and normally with PLC and visu- alization projects. D Ejector button Ejecting the CF card. E Control button Function depends on the software used. Tab. 8 Operating elements on the service side MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 23: Indication Elements On The Service Side
Flashes if the resistive touch is incorrectly calibrated (touch calibra- tion, → Document «MN05010007Z-EN System Description Windows CE»). E SUPPLY OK (green) Lit if all internal system voltages are present. Tab. 9 Indication elements on the service side MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 24 4 Operating and indication elements 4.3 Indication elements on the service side MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 25: Installation
5 Installation 5.1 Safety regulations Installation Safety regulations Read Chapter 3 Safety regulations, 15 before installing and commissioning the de- vice. This contains important information for your personal safety. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 26: Requirements For The Place Of Installation
The ambient conditions stated must be observed. See Chapter 9.9 Ambient conditions, 79. Sufficient ventilation (cooling) must be ensured by means of: Clearance of at least 3 cm to the ventilation slots MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 27 Material thickness at the mounting cutout 2…5 mm (devices with 4-hole front: 2…20 mm) Flatness ≤ 0.5 mm (this requirement must also be fulfilled when the device is mounted!) Surface roughness Rz ≤ 120 MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 28: Cable Preparation
The cables used must be prepared according to the interface description in this document. The wiring instructions for the relevant interface must be observed when wiring the device. Any generally applicable regulations and standards must be fulfilled. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 29: Overview Of Interfaces
E USB Host 0 → Chapter 5.3.7, 35 F USB Host 1 → Chapter 5.3.7, 35 G CAN → Chapter 5.3.8, 36 H DIAG Only for service tasks Tab. 10 Overview of interfaces MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 30: Preparation Of Cables With D-Sub Connector
The folded back shield braid end must be covered by the heat shrinkable tubing or by the rubber grommet. Fit the D-Sub connector to the cable end: The exposed metal shield braid must be clamped to the connector casing with the cable clamp. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 31 E D-Sub connector C Cable clamp F Mounting screw UNC The EMC values stated in the technical data (immunity and emission) can only be guar- anteed by observing the prescribed cable preparation! MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 32: Power Supply
Pluggable screw terminal Cross-section min. 0.75 mm / max. 2.5 mm (lead or wire) min. AWG18 / max. AWG12 Stripping length 7 mm Tab. 12 Preparing the wiring of the connector MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 33: Rs232 (System Port)
Tab. 14 Relationship of cable length / baud rate When preparing the cables, ensure that there is a low-resistance connection between the cable shield and the connector casing (→ Chapter 5.3.2, 30). MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 34: Ethernet
Communication can be disturbed and the connection mechanics damaged if the Ethernet interface is exposed to severe vibration or the RJ45 plug connection is pulled. Protect the RJ45 connection from severe vibration. Protect the RJ45 connection from pulling on the socket. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 35: Usb Device
5.3.7 USB Host The USB Host interfaces support USB 2.0. Fig. 18 USB Host interface (USB Host, type A) Cable Only use shielded USB standard cable. Maximum cable length: 5 m. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 36: Can
Capacitance per unit length < 60 pF/m ≥ 0.25 mm Core cross-section / max. cable length / 100 m ≥ 0.34 mm / 250 m ≥ 0.75 mm / 500 m Tab. 17 Cable specifications MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 37 No more than two terminations must be provided on each bus segment. Transmission faults can occur if operation is carried out without the correct termina- tion. Fig. 20 Bus segment with four bus stations MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 38: Mounting
The device is not provided with an On/Off switch. If the power supply is not provided with a switch, the device will start up (boot) as soon as it is connected to the power sup- ply. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 39: Fitting The Communication Module In The Device
Avoid contact with components (such as connector pins) that are susceptible to electrostatic discharge. Discharge (by touching a grounded metal object) any static charge accumulated in your body before touching the device. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 40 Fit the communication module in the slot. Fasten the communication module with the two knurled screws. Refer to the relevant module description for information on protocol, configuration, cable lengths etc. of the communication module to be used. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 41: Mounting A Device With Standard Front
Material thickness at the mounting cutout 2…5 mm 329.0 344.0 +1/-1 +1/-1 Fig. 22 Mounting cutout for 10.4" devices Fig. 23 Mounting cutout for 12.1" devices 410.0 +1/-1 Fig. 24 Mounting cutout for 15" devices MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 42 Fig. 25 Groove for sealing strip (A) Fit the supplied threaded pins in the retaining brackets beforehand. Fig. 26 Threaded pin pre-fitted in a retaining bracket Fit the device from the front into the mounting cutout. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 43 Top and bottom of the device: Fit one retaining bracket each at the left and right fixing position Fig. 27 10.4" and 12.1" devices with four retaining brackets (do not meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 44 One retaining bracket each at the second fixing position from the left and from the right Left and right on the device: One retaining bracket each at the top and bottom fixing position Fig. 29 15" devices with eight retaining brackets (do not meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 45 One retaining bracket each at the outermost and at the two innermost fixing positions Left and right on the device: One retaining bracket each at the two innermost fixing positions Fig. 30 15" devices with twelve retaining brackets (meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 46: Mounting A Device With 4-Hole Front
15" devices: From 430 mm (±0.2 mm) to 290 mm (±0.2 mm) Material thickness at the mounting cutout 2…20 mm 344.0 314.0 +1/-1 +1/-1 326.0 360.0 +0.2/-0.2 +0.2/-0.2 Fig. 31 Mounting cutout for 10.4" devices Fig. 32 Mounting cutout for 12.1" devices MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 47 CAUTION Poor sealing Poor sealing resulting from inaccurately positioned front seal. Ensure that the front seal is flat and fitted evenly between the front plate of the device and the mounting surface. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 48 Use the supplied countersunk screws and optional counter frame if: Mounting is required to comply with IP65, or The device is used in a potentially explosive atmosphere. Fig. 35 Counter frame (for mounting to IP65) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 49: Mounting A Device With Stainless Steel Front
15" devices: 410 × 315 mm (±1 mm) Material thickness at the mounting cutout 2…5 mm 329.0 344.0 +1/-1 +1/-1 Fig. 36 Mounting cutout for 10.4" devices Fig. 37 Mounting cutout for 12.1" devices MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 50 Do not twist the sealing strip when it is inserted. Cut the sealing strip to a suitable length so that the join is tight. Fig. 39 Groove for sealing strip (A) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 51 Top and bottom of the device: Fit one retaining bracket each at the left and right fixing position Fig. 41 10.4" and 12.1" devices with four retaining brackets (do not meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 52 One retaining bracket each at the second fixing position from the left and from the right Left and right on the device: One retaining bracket each at the top and bottom fixing position Fig. 43 15" devices with eight retaining brackets (do not meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 53 One retaining bracket each at the outermost and at the two innermost fixing positions Left and right on the device: One retaining bracket each at the two innermost fixing positions Fig. 44 15" devices with twelve retaining brackets (meet IP65 requirements) MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
- Page 54 5 Installation 5.4 Mounting MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 55: Operation
If condensation is present on the device, or if it was exposed to temperature fluc- tuations, it must be allowed to adjust to room temperature (do not expose the de- vice to the direct heat of heating devices) prior to commissioning. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 56: Starting The Device
CF card with data in CF slot 1 (B) Do not apply any force (CF cards are protected against reverse insertion). Fig. 46 Service side of the device (CF slot cover removed) Fit the CF slot cover (A). MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 57 System Description Windows CE»): Adjust the system settings of the device. Install the required application programs. The lifespan of the backlight can be increased by reducing the brightness (→ Document «MN05010007Z-EN System Description Windows CE»). MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 58: Switching Off The Device
(CCFL) of the backlight. Avoid frequent on/off switching of the device. Reduce the brightness of the backlight instead (→ Document «MN05010007Z-EN System Description Windows CE»). De-energize the device. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 59: Maintenance And Service
7 Maintenance and service 7.1 Safety regulations Maintenance and service Safety regulations Read Chapter 3 Safety regulations, 15 before working with the device. This contains important information for your personal safety. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 60: Maintenance
Recalibrating a resistive touch The resistive touch is already calibrated when delivered. However, it must be recalibrated if it does not respond correctly to touch operation. Touch calibration, see Document «MN05010007Z-EN System Description Windows CE». MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 61: Cleaning The Infra-Red Touch
With stubborn contamination, spray a little cleaning agent onto the damp cloth first. 7.2.4 Recalibrating the infra-red touch Devices with infra-red touch do not have to be recalibrated. 7.2.5 Battery The integrated battery cannot be exchanged. Lifespan, see Chapter 9.4 System, 74. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 62: Service
Repairs The device must only be opened by the manufacturer or by an authorized repair center. Contact your local supplier or Eaton technical support for repairs. Only the original packaging should be used for transporting the device. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 63: Troubleshooting
Start (boot) the device. Calibrate touch (→ Document «MN05010007Z-EN System Description Windows CE»). Infra-red frame of the infra-red touch is contam- Clean the infra-red frame inated. (→ Chapter 7.2.3, 61). MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 64 The threaded pins for mounting the device have Loosen the threaded pins (observe max. torque, → Chapter 5.4, 38). been tightened too much. Device is faulty. Send in your device for repair. Tab. 19 Troubleshooting MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...
-
Page 65: Storage, Transport And Disposal
Damage to the device must be prevented during transport (use an appropriate packaging). The ambient conditions must be fulfilled even when the device is transported. See Chapter 9.9 Ambient conditions, 79. Check the device on arrival for damage in transit. MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 66: Disposal
10.4" and 12.1" devices Cardboard with PE foil Plastic bag: Polyethylene (PE) 15" devices Closed-cell polyethylene foam, CFC-free Plastic bag: Polyethylene (PE) Tab. 21 Materials used in the packaging MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 67: Technical Data
329 mm × 238 mm (±1 mm) Weight Devices with standard front Approx. 4.1 kg Devices with stainless steel front Approx. 5.3 kg Tab. 22 Dimensions and weights of the 10.4" devices with standard or stainless steel front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 68: Devices With 4-Hole Front
Thickness of front plate 5 mm Mounting depth 88 mm 314 mm × 238 mm (±1 mm) Mounting cutout Weight Approx. 4.1 kg Tab. 23 Dimensions and weights of the 10.4" devices with 4-hole front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 69: Devices With Standard Or Stainless Steel Front
344 mm × 262 mm (±1 mm) Weight Devices with standard front Approx. 4.5 kg Devices with stainless steel front Approx. 5.7 kg Tab. 24 Dimensions and weights of the 12.1" devices with standard or stainless steel front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 70: Devices With 4-Hole Front
Thickness of front plate 5 mm Mounting depth 88 mm Mounting cutout 344 mm × 262 mm (±1 mm) Weight Approx. 4.5 kg Tab. 25 Dimensions and weights of the 12.1" devices with 4-hole front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 71: 15" Devices With Standard Or Stainless Steel Front
Mounting cutout Weight Devices with standard front Approx. 6.2 kg Devices with stainless steel front Approx. 7.5 kg Tab. 26 Dimensions and weights of the 15" devices with standard or stainless steel front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 72: 15" Devices With 4-Hole Front
Thickness of front plate 5 mm Mounting depth 94 mm Mounting cutout 410 mm × 315 mm (±1 mm) Weight Approx. 6.2 kg Tab. 27 Dimensions and weights of the 15" devices with 4-hole front MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 73: Display
2× CCFL, dimmable via software 15" devices 4× CCFL, dimmable via software Lifespan Normally 50 000 h Resistive touch back panel Touch sensor (absolutely flat, seamless) Infra-red touch protective panel Non-reflective safety glass Tab. 28 Display MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 74: Touch Sensor
2× CompactFlash Card Type I/II for operating system, programs and data Real-time clock (battery backup) Battery type CR2032 (190 mA/h), maintenance-free (soldered) Backup time in de-energized state Normally 10 years Tab. 31 System MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 75: Interfaces
Max. 32 W 15" devices Basic device Max. 30 W (normally 28 W) Communication module 2 × max. 4 W USB stations on USB host 2 × max. 3 W Total Max. 44 W MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 76: Enclosure Ratings
Additional set of retaining brackets (optional) For devices with 4-hole front: Counter frame (optional) For 15" devices with stainless steel front: Additional set of retaining brackets (optional) Rear IP20 Tab. 34 Enclosure ratings MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 77: Agency Approvals And Standards
II 3D Ex II T70°C IP5x (ATEX 94/9/EC): Zone 22, category 3D: Required accessories for mounting: - Additional set of retaining brackets (optional) UL 60950: File no. E208621 Tab. 35 Agency approvals and standards MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 78: Applicable Standards And Regulations
(Engineering conditions of acceptability by UL, → Chapter 5.2.2, 26) Product standards EN 50178 Electronic equipment for use in power installations EN 61131-2 Programmable logic controllers, equipment require- ments and tests Tab. 36 Applicable standards and regulations MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... -
Page 79: Ambient Conditions
0 … 50°C Storage / Transport -20 … 60°C Relative air humidity 10 … 95%, non-condensing Vibration According to IEC68-2-6 Shock According to IEC68-2-27 Fall test According to IEC68-2-32 Tab. 37 Ambient conditions MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com... - Page 80 9 Technical data 9.9 Ambient conditions MICRO PANEL XV400 10.4"/12.1"/15" 12/2010 MN04802010Z-EN www.eaton.com...