Lexmark W840 Finisher Service Manual page 312

4024-XXX
287.05 sensor (upper media exit) static jam A
287.06 sensor (upper media exit) static jam B
287.07sensor (upper media exit) static jam C
288.00 sensor (diverter gate) on jam
288.01 sensor (diverter gate) static jam (to top bin) A
2-51
288.02 sensor (diverter gate) static jam (to top bin) B
2-52
288.03 sensor (diverter gate) static jam (to top bin) C
2-53
288.04 sensor (diverter gate) static jam (to stacker bin) A
2-54
288.05 sensor (diverter gate) static jam (to stacker bin) B
2-55
288.06 sensor (diverter gate) static jam (to stacker bin) C
2-56
980.02 finisher communication failure
2-57
981.00 stacker bin fail
981.01 stacker bin upper limit failure
981.02 stacker bin lower limit failure
982.00 sensor (front tamper HP) on failure
982.01 sensor (front tamper HP) off failure
983.00 sensor (rear tamper HP) on failure
983.01 sensor (rear tamper HP) off failure
984.00 sensor (punch unit HP) on failure
984.01 sensor (punch unit HP) off failure
985.00 sensor (punch carriage shift HP) on failure
985.01 sensor (punch carriage shift HP) off failure
986.00 sensor (media eject clamp HP) on failure
986.01 sensor (media eject clamp HP) off failure
987.00 sensor (media eject shaft HP) on failure
988.00 sensor (punch unit side reg) on failure
988.01 sensor (media eject shaft HP) off failure
988.01sensor (punch unit side reg) off failure
989.00 stapler unit failure
990.00 sensor (stapler carriage HP) on failure
990.01 sensor (stapler carriage HP) off failure
995.00 finisher NVRAM R/W failure
996.00 finisher type failure
999.00 finisher engine/RIP functional failure
error messages
bridge unit top cover open
bridge unit top door open
finisher eject cover open
finisher front door open
finisher upper media bin full
2-85
no punch waste box
2-86
punch waste box full
stacker lower safety failure
stacker media bin full (mix size)
stacker media bin full (no mix)
stacker set over count failure
2-92
staple cartridge empty
4-1
ESD-sensitive parts
F
finisher
4-4
removal
finisher controller card assembly
FINISHER TESTS
I-2
Finisher Service Manual
2-46
2-47
2-48
2-49
2-56
2-59
2-60
2-62
2-63
2-64
2-65
2-66
2-67
2-70
2-71
2-72
2-75
2-74
2-76
2-78
2-78
2-79
2-80
2-80
2-81
2-81
2-83
2-83
2-82
2-84
2-90
2-86
2-88
2-92
4-118
3-2
Feed Tests
Hole Punch Test
3-2
Sensor Test
Bin Level
Fin upper bin full
Stacker bin level encod
Stacker bin level1
Stacker bin level2
Stacker bin no media
Stacker bin upper limit
Cover and Door
Cover F bridge top
Door G fin front
Surface H fin eject
Media Path
Bridge media ent
Bridge media exit
Buffer path
Compiler media in
Fin media enter
Fuser exit
Lower media exit
Upper media exit
Media Path2
Diverter gate
Eject clamp hp
2-68
Front tamper hp
2-69
Media eject shaft hp
Rear tamper hp
Punch and Staple
Low staple
Punch box set
Punch cam front
Punch carriage shift hp
Punch hole select
Punch side reg1
Punch side reg2
Punch unit hp
Punch waste full
Stapler carriage shift hp
3-2
Staple Test
front door
parts catalog
H
handling ESD-sensitive parts
I
installation, confirm status
L
4-28
left lower cover
left upper cover
3-2
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
3-3
7-8
4-1
2-2
4-29