Page 1: Technical Reference
Technical Reference May 2006 Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc., registered in the United States and/or other countries. © 2006 Lexmark International, Inc. 740 West New Circle Road Lexington, Kentucky 40550 www.lexmark.com...
Page 2 • This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark components. • The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of other replacement parts.
Page 3: Table Of Contents
Lexmark T640, T642, T644...2-6 Lexmark W840 ... 2-8 Print Area Menu Item... 2-10 Font and Symbol Set Support for the Lexmark T430, T430d, T430dn, T640, T642, and T644 ... 2-12 Forward and Backward Compatibility Modes for the Lexmark T430, T430d, T430dn, T640, T642, and T644 ...2-13 Selecting Symbol Sets for Lexmark T430, T430d, and T430dn...
Page 4 Printer Job Language ...3-1 PJL Command Notation ... 3-1 Kernel Commands... 3-2 Job Separation Commands ... 3-4 Environment Commands and Variables ...3-7 Common Variables for PCL Emulation ... 3-48 Status Readback Commands... 3-54 Status Message Format ... 3-61 Information Messages... 3-61 Auto-Continuable Conditions ...
Page 5 Status Messages... 4-94 Switching Languages ...5-1 SmartSwitch ...5-1 Setting SmartSwitch for Different Interfaces ... 5-2 Printer Job Language ...5-2 Sniffing...5-3 Flash Memory and Disk ...6-1 Resource Data Collection (Download Target) ... 6-2 Storing Resources on Flash Memory or Disk... 6-3 Viewing the Contents of Flash Memory and Disk...6-3...
Page 6 Parallel Interface... 8-7 Standard Parallel Connector ... 8-8 Using the INIT* Signal to Initialize... 8-8 Computer-to-Printer Communications... 8-8 Printer-to-Computer Communication (Advanced Status)... 8-13 Parallel Mode 1 ... 8-14 Parallel Mode 2 ... 8-15 Signal Descriptions ... 8-15 Using the RS-232C Serial Interface ... 8-18 Network Support...
Page 7 TOC-5 Contents PCL Support ... A-1 PJL Support ... B-1 PostScript Support ... C-1 Index... X-1...
Page 8: Introduction
To determine which commands and languages your printer supports, see the appendixes in the back of this document or see your printer documentation. If your printer is not included in this edition of the Technical Reference, it may be available in another version. Visit the Lexmark Web site at www.lexmark.com/ publications for more information.
Page 9 Provides information on printer interfaces, including information about parallel and serial interface, network support, and communication protocols. See the tables in the three appendixes to determine if your printer supports a particular PCL emulation, PJL, or PostScript emulation command. The appendixes...
Page 10 Introduction Appendix A: “PCL Support” Appendix B: “PJL Support” Appendix C: “PostScript Support”...
Page 11: Navigational Tips
OK. You should be aware that if you print this document on a color printer, the color you see on the paper may not match the color you see on your computer monitor.
Page 12: Bibliography
Bibliography For detailed information about PCL emulation printer commands, PostScript emulation printer commands and operators, and interfaces, see the following documentation: • Hewlett-Packard DeskJet Printer Family Technical Reference, C2121-90101 • Hewlett-Packard LaserJet 4 Typography and Graphics, Random House Electronic Publishing •...
Page 13: Pcl Emulation
When SmartSwitch is enabled for both printer languages on an interface (for example, Parallel, USB, Serial Option 1, or Network Option 1), the printer automatically switches to the printer language being sent by your software program. The printer is shipped with SmartSwitch enabled for both printer languages in all interfaces. The printer examines all print jobs and switches dynamically between PostScript emulation and PCL emulation.
Page 14: Using Your Software Program
To select PCL emulation, use the Printer Job Language (PJL) Enter Language Command. See “ENTER LANGUAGE Command” on page 3-3 for more information. See “Printer Job Language” on page 3-1 for the syntax and use of PJL. Warning: When you change printer languages, you may lose some or all previously downloaded resources, unless are stored in flash memory or on disk.
Page 15: Page Formatting
The tables beginning on page 2-4 list the page sizes and dimensions of each area labeled on the preceding diagram for all paper and envelope sizes your printer supports. If information about your printer is not included in the following tables, see page 1-1 for information on how to get a Technical...
Page 16: Lexmark T430, T430D, T430Dn
The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Page 17 The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Page 18: Lexmark T640, T642, T644
The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Page 19 The width of the logical page for A4 paper can be changed from the printer operator panel or your software application. Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039.
Page 20: Lexmark W840
Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039. Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item”...
Page 21 Paper ID 99 will be supported for backward compatibility with other Lexmark printers. Paper ID 99 has the same logical paper size as ID 100 (compatible with HP LaserJet 5Si/5SiMx) but is 8 pels wider than the Lexmark 4039. Note: The explanation of the printable area assumes the Print Area menu item is set to Normal. For more information, see “Print Area Menu Item”...
Page 22: Print Area Menu Item
The physical page border is the actual physical boundaries of a page. Print Area MarkVision Professional. For some printers, Print Area supports three values: Normal, Whole Page, and Fit to Page. See your printer documentation for more information Legend: Logical...
Page 23 Whole Page setting. The printer holds this formatted image in memory, but when the page prints, the image is compressed a small amount in both horizontal and vertical directions, and then centered on the physical page for letter-size paper only.
Page 24: Font And Symbol Set Support For The Lexmark T430, T430D, T430Dn, T640, T642, And T644
Font and Symbol Set Support for the Lexmark T430, T430d, T430dn, T640, T642, and T644 Your printer has 91 resident fonts in PCL emulation, including 89 scalable fonts and two bitmapped fonts. Several parameters are used to select a font from the data stream. These include symbol set, spacing, point or pitch, style, weight, and typeface number.
Page 25: Forward And Backward Compatibility Modes For The Lexmark T430, T430D, T430Dn, T640, T642, And T644
Hewlett-Packard Company’s LaserJet 4050. The backward compatibility mode is used for compatibility with the Hewlett-Packard Company’s LaserJet 5 and the Lexmark family of printers. Standard PCL Emulation Fonts The following table lists the font selection commands for forward and backward compatibility mode for each of the 47 standard PCL emulation fonts.
Page 26 Antique Olive Italic Antique Olive Bold Albertus Medium Albertus Extra Bold Clarendon Condensed Bold Marigold Coronet Line Printer 16 This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. 2-14 Forward and Backward Compatibility Mode Spacing Style Weight Typeface...
Page 27: Type 1 Fonts
Notice the values for forward and backward compatibility modes differ slightly for Bold. This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. This font is not implemented in the Lexmark family of printers. 2-15 Forward and Backward Compatibility Mode...
Page 28 ITC Zapf Dingbats Notice the values for forward and backward compatibility modes differ slightly for Bold. This font is not implemented in the Hewlett-Packard Company’s LaserJet 4050. This font is not implemented in the Lexmark family of printers. 2-16 Backward Compatibility Mode...
Page 29: Selecting Symbol Sets For Lexmark T430, T430D, And T430Dn
To determine if a font or typeface supports a symbol set, see the complete listing of PCL emulation fonts and symbol sets in the following tables: “Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials” on page 2-29, “Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1”...
Page 30 To determine if a font or typeface supports a symbol set, see the complete listing of PCL emulation fonts and symbol sets in the following tables: “Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek” on page 2-23, “Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1”...
Page 31 2-19 Table 2-7: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Times New Roman Times New Roman Italic Times New Roman Bold Times New Roman Bold Italic...
Page 32 2-20 Table 2-7: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID CG Omega Italic CG Omega Bold CG Omega Bold Italic Antique Olive Antique Olive Italic...
Page 33 2-21 Table 2-7: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Palatino Italic Palatino Bold Palatino Bold Italic ITC Bookman Light ITC Bookman Light Italic ITC Bookman Demi...
Page 34 2-22 Table 2-7: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Times Roman Times Italic Times Bold Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black...
Page 35 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek Latin 2 Typeface / Symbol PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic...
Page 36 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Arial Bold Italic Letter Gothic Letter Gothic Italic Letter Gothic Bold...
Page 37 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Antique Olive Italic Antique Olive Bold Albertus Medium Albertus Extra Bold...
Page 38 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Palatino Bold Italic ITC Bookman Light ITC Bookman Light Italic ITC Bookman Demi...
Page 39 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID CourierPS CourierPS Oblique CourierPS Bold CourierPS Bold Oblique Times Roman Times Italic...
Page 40 Table 2-8: T430, T430d, T430dn PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set.
Page 41 2-29 Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials Specials Typeface / Symbol Set PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic...
Page 42 2-30 Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium Univers Condensed Medium Italic Univers Condensed Bold Univers Condensed Bold Italic...
Page 43 2-31 Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Coronet Helvetica Helvetica Italic Helvetica Bold Helvetica Bold Italic Helvetica Narrow Helvetica Narrow Italic Helvetica Narrow Bold...
Page 44 2-32 Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Century Schoolbook Roman Century Schoolbook Italic Century Schoolbook Bold Century Schoolbook Bold Italic ITC Zapf Chancery Medium Italic...
Page 45 Table 2-9: T430, T430d, T430dn PCL Emulation Symbol Sets - Specials (Continued) Typeface / Symbol Set PJL Value Symbol Set ID C39 Wide OCR-A OCR-B Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 46 Table 2-10: T430, T430d, T430dn ISO PCL Emulation Symbol Sets (Continued) Symbol Set ID Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Courier Courier Italic Courier Bold...
Page 47 2-35 Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID CG Times Bold Italic Univers Medium Univers Medium Italic Univers Bold Univers Bold Italic Times New Roman Times New Roman Italic Times New Roman Bold Times New Roman Bold Italic...
Page 48 2-36 Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Garamond Antiqua Garamond Kursiv Garamond Halbfett Garamond Kursiv Halbfett CG Omega CG Omega Italic CG Omega Bold CG Omega Bold Italic Antique Olive Antique Olive Italic...
Page 49 2-37 Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Helvetica Narrow Helvetica Narrow Italic Helvetica Narrow Bold Helvetica Narrow Bold Italic Palatino Roman Palatino Italic Palatino Bold Palatino Bold Italic ITC Bookman Light...
Page 50 Times Roman Times Italic Times Bold Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow C39 Regular C39 Wide OCR-A OCR-B Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 51 2-39 Table 2-11: T640, T642, T644 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 52 Table 2-12: T640, T642, T644 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek Latin 2 Typeface / Symbol PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic Univers Medium...
Page 53 Table 2-12: T640, T642, T644 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Arial Italic Arial Bold Arial Bold Italic Letter Gothic Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium...
Page 54 Table 2-12: T640, T642, T644 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID CG Omega Bold Italic Antique Olive Antique Olive Italic Antique Olive Bold Albertus Medium Albertus Extra Bold Clarendon...
Page 55 Table 2-12: T640, T642, T644 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Palatino Italic Palatino Bold Palatino Bold Italic ITC Bookman Light ITC Bookman Light Italic ITC Bookman Demi ITC Bookman Demi...
Page 56 Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow C39 Regular Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set. 2-44 Latin 5...
Page 57 Table 2-12: T640, T642, T644 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID C39 Wide OCR-A OCR-B Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 58 2-46 Table 2-13: T640, T642, T644 PCL Emulation Symbol Sets - Specials Specials Typeface / Symbol Set PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic Univers Medium Univers Medium Italic Univers Bold...
Page 59 2-47 Table 2-13: T640, T642, T644 PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium Univers Condensed Medium Italic Univers Condensed Bold Univers Condensed Bold Italic Garamond Antiqua Garamond Kursiv Garamond Halbfett...
Page 60 2-48 Table 2-13: T640, T642, T644 PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Coronet Helvetica Helvetica Italic Helvetica Bold Helvetica Bold Italic Helvetica Narrow Helvetica Narrow Italic Helvetica Narrow Bold Helvetica Narrow Bold Italic Palatino Roman Palatino Italic...
Page 61 Times Bold Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow C39 Regular Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 62 Table 2-13: T640, T642, T644 PCL Emulation Symbol Sets - Specials (Continued) Typeface / Symbol Set PJL Value Symbol Set ID C39 Wide OCR-A OCR-B Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set. All fonts that support the Roman-8 (8U) symbol set also support the following 19 symbol sets.
Page 63: Selecting Symbol Sets For The Lexmark W840
Table 2-14: T640, T642, T644 ISO PCL Emulation Symbol Sets (Continued) Symbol Set ID Selecting Symbol Sets for the Lexmark W840 To determine if a font or typeface supports a symbol set, see the complete listing of PCL emulation fonts and symbol sets in the following tables: “Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1”...
Page 64 2-52 Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1 Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic Univers Medium Univers Medium Italic Univers Bold...
Page 65 2-53 Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Arial Bold Arial Bold Italic Letter Gothic Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium Univers Condensed Medium Italic Univers Condensed Bold Univers Condensed Bold Italic Garamond Antiqua...
Page 66 2-54 Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Albertus Medium Albertus Extra Bold Clarendon Condensed Bold Marigold Coronet Helvetica Helvetica Italic Helvetica Bold Helvetica Bold Italic Helvetica Narrow Helvetica Narrow Italic Helvetica Narrow Bold...
Page 67 2-55 Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID ITC Bookman Demi Italic ITC Avant Garde Book ITC Avant Garde Book Oblique ITC Avant Garde Demi ITC Avant Garde Demi Oblique Century Schoolbook Roman Century Schoolbook Italic...
Page 68 Table 2-15: W840 PCL Emulation Symbol Sets - Latin 1 (Continued) Latin 1 Typeface / Symbol Set PJL Value Symbol Set ID Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow C39 Regular C39 Wide OCR-A OCR-B...
Page 69 Table 2-16 W840 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek Latin 2 Typeface / Symbol PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic Univers Medium Univers Medium Italic...
Page 70 Table 2-16 W840 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Arial Italic Arial Bold Arial Bold Italic Letter Gothic Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium Univers Condensed...
Page 71 Table 2-16 W840 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID CG Omega Bold Italic Antique Olive Antique Olive Italic Antique Olive Bold Albertus Medium Albertus Extra Bold Clarendon Condensed Bold...
Page 72 Table 2-16 W840 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID Palatino Italic Palatino Bold Palatino Bold Italic ITC Bookman Light ITC Bookman Light Italic ITC Bookman Demi ITC Bookman Demi...
Page 73 Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow C39 Regular Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set. 2-61 Latin 5...
Page 74 Table 2-16 W840 PCL Emulation Symbol Sets - Latin 2, Latin 5, Latin 6, Cyrillic, Greek (Continued) Latin 2 Typeface / Symbol PJL Value Symbol Set ID C39 Wide OCR-A OCR-B Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 75 2-63 Table 2-17: W840 PCL Emulation Symbol Sets - Specials Specials Typeface / Symbol Set PJL Value Symbol Set ID Courier Courier Italic Courier Bold Courier Bold Italic CG Times CG Times Italic CG Times Bold CG Times Bold Italic Univers Medium Univers Medium Italic Univers Bold...
Page 76 2-64 Table 2-17: W840 PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Letter Gothic Letter Gothic Italic Letter Gothic Bold Univers Condensed Medium Univers Condensed Medium Italic Univers Condensed Bold Univers Condensed Bold Italic Garamond Antiqua Garamond Kursiv Garamond Halbfett...
Page 77 2-65 Table 2-17: W840 PCL Emulation Symbol Sets - Specials (Continued) Specials Typeface / Symbol Set PJL Value Symbol Set ID Marigold Coronet Helvetica Helvetica Italic Helvetica Bold Helvetica Bold Italic Helvetica Narrow Helvetica Narrow Italic Helvetica Narrow Bold Helvetica Narrow Bold Italic Palatino Roman Palatino Italic Palatino Bold...
Page 78 Times Italic Times Bold Times Bold Italic Helvetica Light Helvetica Light Oblique Helvetica Black Helvetica Black Oblique Line Printer 16 POSTNET Barcode C39 Narrow Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set.
Page 79 Table 2-17: W840 PCL Emulation Symbol Sets - Specials (Continued) Typeface / Symbol Set PJL Value Symbol Set ID C39 Regular C39 Wide OCR-A OCR-B Wingdings Symbol SymbolPS ITC Zapf Dingbats Indicates Typeface supports the specified Symbol Set. Indicates Typeface does not support the specified Symbol Set. Table 2-18: W840 Symbol Sets Symbol Set ID 2-67...
Page 80: Command Structure
Table 2-18: W840 Symbol Sets (Continued) Symbol Set ID Command Structure This section introduces the different types of PCL emulation commands and their structure, or syntax. It also demonstrates how you can link commands to abbreviate them. Control Codes Control Codes are single-character instructions. Table 2-19: Control Codes Code Function...
Page 81: Commands
A command parameter sets the value for a command. This value stays constant until either a different value resets the command or a command resets the printer to the default values. For example, after the printer receives a command that selects a right margin beginning at column 63, the right margin of each printed page begins at column 63.
Page 82 the grid from the desired parameter and read the value in the top heading. This is the first character of the hex value. Next, go straight across the grid to the left of the parameter and read the value in the left column heading. This is the second character of the hex value.
Page 83: Pcl Emulation Commands
(s3B PCL Emulation Commands See the following tables for a listing of the commands grouped by function. To determine which commands your printer supports, see “Table A-1: PCL Emulation Commands” on page A-1. PCL Emulation Commands by Function Table 2-21: Job Control Command / Parameters &d#A...
Page 84 Universal Exit Language (UEL) / Start of PJL This command terminates the current printer language and allows switching into PJL. For more information, see “UNIVERSAL EXIT LANGUAGE Command” on page 3-2.
Page 85 1, tray 2, tray 3, tray 4, tray 5, and envelope feeder. Notes: • When the printer receives the page size command, any partially formatted pages are printed, and the cursor position and margins are reset.
Page 86 Sets the feed direction of Universal size. Feed direction means which side of the print media, either the short edge or the long edge, feeds through the printer first. Set Universal Custom Name Sets the user-specified custom name for the Universal paper size being used.
Page 87 Sets Vertical Motion Index in 1/48 inch increments. The VMI determines the vertical distance between lines. Notes: • For some printers, you can change the default VMI from the printer operator panel or through MarkVision Professional by using the menu item. See your printer documentation for more Lines Per Page information.
Page 88 Set Line Spacing (Alternative Method) Specifies VMI in lines per inch. Notes: • For some printers, you can change the default VMI from the printer operator panel or through MarkVision Professional by using the menu item. See your printer documentation for more Lines Per Page information.
Page 89 Table 2-23: Alphanumeric ID Command / Parameters &n#W [operation] [string] # = number of data bytes that make up the operation and string Operation operation = 100 or 1 byte = 0x64 or For example: Media Select String string = See Alphanumeric String list at right Table 2-24: Cursor Positioning Command / Parameters...
Page 90 Half Line-Feed Moves the cursor down 1/2 line (1/2 of the current VMI). Set Line Termination Controls how the printer responds to the Carriage Return (CR), Line Feed (LF), and Form Feed (FF) control codes. Push / Pop Cursor Position Sets up a cursor position stack for storing and recalling various cursor positions.
Page 91 Select Style Identifies the physical traits of a character and the composition of the font symbols. Note: You can only use this command to select fonts currently available in the printer. It cannot alter the appearance of the available fonts.
Page 92 # Typeface identifier (0 - 65535) Note: For a list of typeface numbers, see Table 2-4 on page 2-13 and “Font and Symbol Set Support for the Lexmark T430, T430d, T430dn, T640, T642, and T644” on page 2-12. (#X (primary)
Page 93 Table 2-25: Font Selection (Continued) Command / Parameters &t#P 0, 1 1 byte characters 1 or 2 byte characters 1 or 2 byte characters 1 or 2 byte characters 1008 1, 2, or 3 byte characters (UTF-8) &k#S 10.00 cpi 16.66 cpi 12.00 cpi Table 2-26: User-Defined Symbol Set...
Page 94 Table 2-27: Font Creation Command / Parameters *c#D # = Font ID # (0 - 32767) Default = 0 )s#W[data] # = number of data bytes *c#F Delete all (temporary and permanent) Delete all temporary Delete previous font ID Delete previous specified character Make previous font ID temporary Make previous font ID permanent Copy current font...
Page 95 Table 2-29: Print Model Command / Parameters *c#G Gray Scale Fills White (default) 2% gray 3-10 10% gray 11-20 15% gray 21-35 30% gray 36-55 45% gray 56-80 70% gray 81-99 90% gray 100% gray (Black) Cross-Hatch Fills Horizontal line Vertical line Diagonal line Diagonal line...
Page 96 Table 2-30: User-Defined Pattern Command / Parameters *c#W[data] # = number of data bytes *p#R Rotate with print (Default) Fixed *c#Q Delete all patterns (temporary and permanent) Delete all temporary patterns Delete pattern (last ID specified) Make pattern of last ID # temporary Make pattern of last ID # permanent Table 2-31: Rectangular Area Fill Graphics Command / Parameters...
Page 97 Table 2-31: Rectangular Area Fill Graphics (Continued) Command / Parameters *c#G Gray Scale Fills White (default) 2% Gray 3-10 10% Gray 11-20 15% Gray 21-35 30% Gray 36-55 45% Gray 56-80 70% Gray 81-99 90% Gray 100% Gray (Black) Cross-Hatch Fills Horizontal Line Vertical Line Diagonal Line...
Page 98 # = Number of Raster Lines 2-86 Function / Result Raster Resolution Note: 200 dpi is only supported when the printer is operating in 600 dpi or 1200 dpi mode. Raster Graphics Presentation Sets the Raster Image Orientation in relation to the logical page.
Page 99 Table 2-32: Raster Graphics (Continued) Command / Parameters *b#M Uncoded (Default) Run-Length Encoded Tagged Image File Format (TIFF) byte Delta Row Adaptive Compression Replacement Delta Row Zlib 1002 Group 4 1003 Group 3 one dimensional 1004 Group 3 two dimensional K=2 1005 Group 3 two dimensional K=4 1006...
Page 100 Table 2-32: Raster Graphics (Continued) Command / Parameters *t#V *g#W[data] # - 8 (K-only) or 26 (KCMY) Data Byte 0 - 0x02 (constant) Byte 1 - number of colors 0x01 - K only 0x04 - CMYK Byte 2,3 - X res for K plane 0x012C (300) or 0x0258 (600) Byte 4,5 - Y res for K plane 0x012C (300) or 0x0258 (600)
Page 101 Table 2-33: Color Extensions Command / Parameters &b#M Print in mixed render algorithm mode Print using gray scale equivalent &p#C Delete all palettes except those in stack (active palette is deleted) Delete all palettes in stack (active palette not affected) Delete palette specified by Palette Control ID Copy active palette to ID...
Page 102 Table 2-33: Color Extensions (Continued) Command / Parameters *t#I Gamma Correction Off 0.0 to 4.0 Gamma Number *t#J *v#A -32767.0 to 32767.0 *v#B -32767.0 to 32767.0 *v#C -32767.0 to 32767.0 *v#I # = Palette Index 0 to 2 – 1 = Palette Index *v#S # = Palette Index 0 to 2...
Page 103 Set Status Readback Location Type Sets the status location type to the specified value. The 5 value for Cartridge may be specified, but since your printer does not support font cards or cartridges, the command is ignored. The 7 value for User-installable flash is only valid when flash memory is installed.
Page 104 Table 2-35: Picture Frame Command / Parameters *c#X # of Decipoints: 0 to 32767 (1 Decipoint = 1/720 inch) *c#Y # of Decipoints: 0 to 32767 (1 Decipoint = 1/720 inch) *c0T Set Anchor Point to Cursor Position *c#K Size in inches: 0 to 32767 *c#L Size in inches: 0 to 32767 Use Previous GL/2 Pen Position...
Page 105: Gl/2 Commands
Note: GL/2 is not a stand-alone plotter emulation. It can only be entered from within PCL emulation and cannot be used with software without a unique printer driver written explicitly for GL/2. The following tables list the GL/2 commands by group. To determine which GL/2 commands your printer supports, see “Table A-2: GL/2 Commands”...
Page 106 Table 2-37: Configuration Group (Continued) Command / Parameter IR (X IW (X MC (mode(, opcode)); PP (mode); RO (angle); SC (X (, type(, left, bottom))); min, Table 2-38: Vector Group Command / Parameter AA X , sweep_angle(, chord_angle); center center AR X , sweep_angle(, chord_angle);...
Page 107 Table 2-39: Polygon Group (Continued) Command / Parameter RA X, Y; RR X, Y; WG radius, start_angle, sweep_angle(, chord_angle); Table 2-40: Character Group Command / Parameter AD (kind, value(,...)); CF (mode(, pen)); CP (spaces, lines); DI (run, rise); DR (run, rise); DT (label_terminator(, mode));...
Page 108 Table 2-41: Line and Fill Attributes Group Command / Parameter AC (X, Y); CR (red , red , green black ref white ref black ref , blue black ref white ref FT (fill_type(, option1(, option2)); FT22, (PCL User-Defined Pattern ID); FT 9, level;...
Page 109: Raster Image Graphics
These parameters are in effect until you overwrite them with a different command or there is a printer reset. To ensure that the printed image appears in the expected area, set width and height parameters.
Page 110 Descriptions and examples of the different parameters appear on the following pages. Each example draws the same square outline 64 bits (8 bytes) wide by 64 scan lines long. Uncoded Data Uncoded Data is not compressed. Only those bytes needed to form the image are sent.
Page 111 Run-Length Encoded Data Run-Length Encoded Data is interpreted in pairs of bytes. The first byte: • Acts as a counter, or control byte. • Indicates how many times to repeat the data in the second byte. • Can be from 0 (no repetition) to 255. •...
Page 112 Delta Row Delta Row is a compression mode that identifies and transmits only those bytes different from the ones in a preceding row. The control byte consists of two parts: • High 3 bits: Number of bytes to replace +1 (1 to 8). •...
Page 113 Adaptive Compression Adaptive compression allows the combined use of compression methods 0 through 3 (Uncoded, Run-Length Encoded, TIFF, and Delta Row). It also allows the printing of empty rows (all zeros) or duplicate rows. • The Transfer Raster Data command size includes all rows (scan lines). •...
Page 114 Since Group 4 images do not use line endings, the width of the image must be specified using the Raster Width command ( The compressed image data is sent to the printer using the Transfer Raster Data command ( Transfer Raster Data command is 32K bytes. Images larger than 32K bytes must be broken up and sent using multiple commands.
Page 115 Additional Compression Modes When the compression mode is 1008 (Lexmark Adaptive), TIFF word and double- word can be printed using compression scan modes 254 and 255 respectively. This compression method sends a raster image as a block of raster data.
Page 116: Macros
Macros When creating a macro, first assign it an ID number. If this number is identical to an existing macro ID in RAM, the old macro is deleted when you specify the Macro Control Start Definition. Next, start the macro definition, send the contents of the macro, and stop the macro definition.
Page 117: Printer Job Language
Your printer supports complete Printer Job Language (PJL) commands, including certain commands that cause the printer to enter PCL emulation, PostScript emulation, and Personal Printer Data Stream (PPDS). To determine which commands your printer supports, see Appendix B: “PJL Support” on page B-1. PJL Command Notation The syntax for each supported PJL command is listed in this chapter.
Page 118: Kernel Commands
PJL. Syntax: Notes: • If the printer receives this command while in PCL emulation, it performs a Printer Language Reset ( • If the printer receives this command while in PostScript emulation, it performs an End-of-Job (EOJ) command before exiting PostScript emulation (Ctrl-D).
Page 119: Comment Command
ENTER LANGUAGE Command This command causes the printer to enter the specified language, such as PCL emulation, PostScript emulation, or PPDS. Syntax: Notes: • • You can use uppercase, lowercase, or mixed case. ( all others can be mixed or lowercase.) Example: enters PostScript emulation.
Page 120: Job Separation Commands
The host computer can use the JOB command to separate print data into various parts or jobs. Specifically, the JOB command signifies to the printer the start of a print job. Use the EOJ command to signify the end of a job. In addition, use the JOB/EOJ pair to accomplish the following: •...
Page 121 1 of the print job and its range is from 1 to 2,147,483,647. Omission of the END parameter causes the printer to print all pages to the end of the job. A system administrator can control which jobs, and therefore which users, are allowed to modify the printer default or NVRAM variables by declaring a PJL password.
Page 122: Eoj Command
For detailed information on PJL password protection, see “File and Device Protection Commands” on page 3-93. Note: Setting a default PJL password disables the use of PJL DEFAULT and INITIALIZE commands. (See “DEFAULT Command” on page 3-8 and “INITIALIZE Command” on page 3-11.) EOJ Command The EOJ command signifies the end of a print job.
Page 123: Environment Commands And Variables
Environment Commands and Variables This section describes the printer environment variables and the PJL commands used to modify or query the variables. Note: The word common applies to those variables common to both your printer and the Hewlett-Packard Company’s LaserJet printers.
Page 124: Default Command
DEFAULT Command This command modifies the default setting for the specified environment variable and stores the setting in the printer NVRAM. The new setting is activated with the occurrence of the next PJL reset condition. Syntax: to be modified. The variables supported are listed in the tables beginning on page 3-12.
Page 125: Set Command
PJL reset condition. Use the SET command to modify any currently defined environment variable that cannot be set using the desired printer language. For example, use the PJL SET command to set Print Quality Enhancement Technology (PQET) or Page Protect, which cannot be set within a printer language such as PCL emulation.
Page 126 • " variables. (See “Table 3-9: Printer Unique LRESOURCE Variables” on page 3-53.) Values for " A unique identifier for a file, such as the macro ID for a PCL macro, the symbol set ID for a PCL symbol set, the font ID for a PCL font, and so on.
Page 127: Initialize Command
INITIALIZE Command This command restores both the current and default environment variables to their factory default values and updates the printer NVRAM. This command affects all of the variables listed in “Table 3-3: Common Variables for Both Printer Languages” on page 3-12 through “Table 3-8: Printer Unique Variables for PostScript Emulation”...
Page 128: Common Variables For Both Printer Languages
Common Variables for Both Printer Languages Note: The word common applies to those variables common to both your printer and the Hewlett-Packard Company’s LaserJet printers. The following common variables are supported for both PCL emulation and PostScript emulation, unless otherwise noted. Therefore, the [ parameter should not be specified.
Page 129 ON, OFF The value of the NVRAM serial number field is returned. The NVRAM serial number field is set to the printer serial number. In order to guarantee that a unique identifier exists in this field, the printer writes a random alphanumeric string into this field whenever the critical byte area in NVRAM is re-initialized.
Page 130 Table 3-3: Common Variables for Both Printer Languages (Continued) Variable Function HOLDTYPE Print and Hold Type (SET only) IMAGEADAPT Resolution reduction (DEFAULT only) INTRAY2 Tray lock - Tray 2 INTRAY3 Tray lock - Tray 3 INTRAY4 Tray lock - Tray 4...
Page 131 Table 3-3: Common Variables for Both Printer Languages (Continued) Variable Function JOBOFFSET Offset Pages LANG Default display language (DEFAULT only) LOWTONER Toner Alarm (DEFAULT only) MANUALFEED Manual feed selection (READ only) MEDIATYPE Default paper source, default formatting size MPTRAY Multipurpose...
Page 132 Table 3-3: Common Variables for Both Printer Languages (Continued) Variable Function OUTBIN Output Bin PAGEPROTECT Page Protect PAPER Default paper source, default formatting size 3-16 Selections UPPER, LOWER, OPTIONALOUTBIN1, OPTIONALOUTBIN2, OPTIONALOUTBIN3, OPTIONALOUTBIN4, OPTIONALOUTBIN5, OPTIONALOUTBIN6, OPTIONALOUTBIN7, OPTIONALOUTBIN8, OPTIONALOUTBIN9, OPTIONALOUTBIN10, “name” name is a variable that allows for custom naming of optional output bins.
Page 133 Table 3-3: Common Variables for Both Printer Languages (Continued) Variable Function PARALLEL Parallel Protocol (DEFAULT only) (Port Specific) PASSWORD Default password for PJL NVRAM (DEFAULT only) security PERSONALITY SmartSwitch settings (Port specific) POWERSAVE Power Save feature (DEFAULT only) 3-17 Selections...
Page 134 DARK, MEDIUM, LIGHT, and ON values indicate that PQET is On. OFF indicates PQET is Off. 0 to 255 The time the printer remains idle before the job is forced to print. Note: If a value greater than 255 is specified by a SET or DEFAULT command, the value is changed to 255.
Page 135: Printer Unique Variables For Both Printer Languages
A4 width Printer Unique Variables for Both Printer Languages The following variables are unique to some Lexmark printers and are supported for both PCL emulation and PostScript emulation. Therefore, the [ To determine which variables your printer supports, see “Table B-2: Printer Unique PJL Variables for Both Printer Languages”...
Page 136 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LBONDOUTBIN Assign Type/Bin - Bond (DEFAULT only) LBONDTEXTURE Bond Texture (DEFAULT only) LBONDWEIGHT Bond Weight (DEFAULT only) LBWLOCK Black & White Lock LCANCEL Cancel Control LCARDSTOCKLENGTH Card Stock...
Page 137 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCARDSTOCKOUTBIN Assign Type/Bin - (DEFAULT only) Card Stock LCARDSTOCKTEXTURE Card Stock Texture (DEFAULT only) LCARDSTOCKWEIGHT Card Stock Weight (DEFAULT only) LCOLLATION Collation Mode LCOLORCORRECTION Indicates which color target the...
Page 138 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCOLOREDLOADING Colored Paper Loading (DEFAULT only) LCOLOREDOUTBIN Assign Type/Bin - (DEFAULT only) Colored Paper LCOLOREDTEXTURE Colored Paper Texture (DEFAULT only) LCOLOREDWEIGHT Colored Paper Weight (DEFAULT only) LCOLORMODEL Color Model...
Page 139 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMPAPERHEIGHT Universal Height LCUSTOMPAPERFEED Universal Feed Direction LCUSTOMTYPE1LENGTH Custom Type 1 Length (DEFAULT only) LCUSTOMTYPE1LOADING Custom Type 1 Paper Loading (DEFAULT only) LCUSTOMTYPE1MEDIA Custom Type 1 Media (DEFAULT only)
Page 140 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE1OUTBIN Assign Type/Bin - (DEFAULT only) Custom Type 1 LCUSTOMTYPE1TEXTURE Custom Type 1 Texture (DEFAULT only) LCUSTOMTYPE1WEIGHT Custom Type 1 Weight (DEFAULT only) LCUSTOMTYPE2LENGTH Custom Type 2 Length...
Page 141 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE2NAME Custom Type 2 Name (DEFAULT only) LCUSTOMTYPE2OUTBIN Assign Type/Bin - (DEFAULT only) Custom Type 2 LCUSTOMTYPE2TEXTURE Custom Type 2 Texture (DEFAULT only) LCUSTOMTYPE2WEIGHT Custom Type 2 Weight...
Page 142 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE3MEDIA Custom Type 3 Media (DEFAULT only) LCUSTOMTYPE3NAME Custom Type 3 Name (DEFAULT only) LCUSTOMTYPE3OUTBIN Assign Type/Bin - (DEFAULT only) Custom Type 3 LCUSTOMTYPE3TEXTURE Custom Type 3 Texture...
Page 143 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE4LOADING Custom Type 4 Paper Loading (DEFAULT only) LCUSTOMTYPE4MEDIA Custom Type 4 Media (DEFAULT only) LCUSTOMTYPE4NAME Custom Type 4 Name (DEFAULT only) LCUSTOMTYPE4OUTBIN Assign Type/Bin - (DEFAULT only)
Page 144 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE5LENGTH Custom Type 5 Length (DEFAULT only) LCUSTOMTYPE5LOADING Custom Type 5 Paper Loading (DEFAULT only) LCUSTOMTYPE5MEDIA Custom Type 5 Media (DEFAULT only) LCUSTOMTYPE5NAME Custom Type 5 Name (DEFAULT only)
Page 145 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE5WEIGHT Custom Type 5 Weight (DEFAULT only) LCUSTOMTYPE6LENGTH Custom Type 6 Length (DEFAULT only) LCUSTOMTYPE6LOADING Custom Type 6 Paper Loading (DEFAULT only) LCUSTOMTYPE6MEDIA Custom Type 6 Media (DEFAULT only)
Page 146 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LCUSTOMTYPE6TEXTURE Custom Type 6 Texture (DEFAULT only) LCUSTOMTYPE6WEIGHT Custom Type 6 Weight (DEFAULT only) LDOWNLOADTARGET Download Target (SET only) LDRYTIMEDELAY Dry Time Delay LDUPLICATEHELDJOBS Delete or Save Print and Hold...
Page 147 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LENVELOPETEXTURE Envelope Texture (DEFAULT only) LENVELOPEWEIGHT Envelope Weight (DEFAULT only) LESCCHAR Character Substitution (READ only) (Port specific) LFAXRESOLUTION Fax Resolution (SET only) LFAXREDIAL Fax Redial (SET only) LFAXREDIALFREQUENCY...
Page 148 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LGLOSSYOUTPUTBIN Assign Type/Bin - Glossy LGLOSSYTEXTURE Glossy Paper Texture LGLOSSYWEIGHT Glossy Paper Weight LHOLEPUNCHALARM Hole Punch Alarm LHOLEPUNCHMODE Hole Punch Mode LHONORINIT Honor INIT Signal (DEFAULT only) (Port specific)
Page 149 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LIMAGEENHANCETYPE Image Enhancement Technology Type LIMAGEORIENTATION Page Image Orientation LIMAGESMOOTHING Image Smoothing for PostScript LINFEEDERSIZE Envelope feeder installed size, default formatting size LINKALERT Ink Alert LINMPFEEDERSIZE Multipurpose feeder installed...
Page 150 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LLABELSOUTBIN Assign Type/Bin - (DEFAULT only) Labels LLABELSTEXTURE Labels Texture (DEFAULT only) LLABELSWEIGHT Labels Weight (DEFAULT only) LLASTTRAYRENUMBER Last Tray Renumber LLEFTMARGINOFFSET Left Margin Offset LLETTERHEADLENGTH Letterhead Length...
Page 151 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LLETTERHEADOUTBIN Assign Type/Bin - (DEFAULT only) Letterhead LLETTERHEADTEXTURE Letterhead Texture (DEFAULT only) LLETTERHEADWEIGHT Letterhead Weight (DEFAULT only) LMANUALCOLORRGBTEXT Manual Color - RGB Text LMANUALCOLORRGB- Manual Color - GRAPHICS...
Page 152 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LMANUALCOLORCMYK- Manual Color - IMAGE CMYK Image LMANUALENVELOPESIZE Manual Envelope, default formatting size LMANUALENVELOPETYPE Manual Envelope Type LMANUALPAPERSIZE Manual Paper, default formatting size LMANUALPAPERTYPE Manual Paper Type LMPFEEDERPAPERTYPE...
Page 153 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LMULTIPAGEPRINT Multipage Printing LMULTIPAGEVIEW Multipage View LNPAP NPA Protocol Setting (READ only) (Port specific) LOPTIONALOUTBIN1NAME Optional Output Bin 1 Name (DEFAULT only) LOPTIONALOUTBIN2NAME Optional Output Bin 2 Name...
Page 154 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LOPTIONALOUTBIN6NAME Optional Output Bin 6 Name (DEFAULT only) LOPTIONALOUTBIN7NAME Optional Output Bin 7 Name (DEFAULT only) LOPTIONALOUTBIN8NAME Optional Output Bin 8 Name (DEFAULT only) LOPTIONALOUTBIN9NAME Optional Output Bin 9 Name...
Page 155 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LOVERFLOWOUTBIN Overflow Bin (DEFAULT only) LOVERFLOWTIMER Overflow Timer, in minutes (DEFAULT only) LPAGECOUNT Page Count (READ only) LPAGEMODE Print Area LPAPERSOURCE Default paper source 3-39 Selections UPPER, LOWER, OPTIONALOUTBIN1,...
Page 156 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LPICTUREGRADE™ PictureGrade™ LPLAINLENGTH Plain Paper Length (DEFAULT only) LPLAINOUTBIN Assign Type/Bin - Plain (DEFAULT only) Paper LPLAINTEXTURE Plain Paper Texture (DEFAULT only) LPLAINWEIGHT Plain Paper Weight (DEFAULT only)
Page 157 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LPPDS Activate Personal Printer (DEFAULT only) Data Stream (PPDS) printer language LPPDSFORMLINES Lines Per Page (PPDS) (DEFAULT only) LPPDSLINESPERINCH Lines Per Inch (DEFAULT only) LPREPRINTEDLENGTH Preprinted Paper Length...
Page 158 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LPREPRINTEDOUTBIN Assign Type/Bin - Preprinted Paper LPREPRINTEDTEXTURE Preprinted Paper Texture (DEFAULT only) LPREPRINTEDWEIGHT Preprinted Paper Weight (DEFAULT only) LPRINTBUFFER Print Buffer control LPRINTHEADIDLETIME Printhead Idle Time (SET only)
Page 159 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LPRINTQUALITY Print Quality Mode LPUNCH Hole Punch LREAROUTBINNAME Rear Output Bin Name LREPEATPRINTLIMIT Print and Hold Repeat Print (DEFAULT only) Job Limit LRESET Reset Control LRESOURCESAVE Resource Save...
Page 160 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LSTANDARDOUTBINNAME Standard Output (DEFAULT only) Bin Name LSTROKEWIDTH PostScript minimum stroke width LSTAPLE Staple Job LSTAPLESEMPTYALARM Staples Empty Alarm (DEFAULT only) LSTAPLETESTBIN Staple Priming (DEFAULT only) LSTAPLETESTSOURCE Staple Priming...
Page 161 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LTRANSPARENCYOUTBIN Assign Type/Bin - (DEFAULT only) Transparency LTRANSPARENCYTEXTURE Transparency Texture (DEFAULT only) LTRANSPARENCYWEIGHT Transparency Weight (DEFAULT only) LTRAY1SENSEDTYPE Detected Type PAPER for Paper - Tray 1 LTRAY1SENSEDTYPE Detected Type...
Page 162 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LTRAY3SENSEDTYPE Detected Type PAPER for Paper - Tray 3 LTRAY3SENSEDTYPE Detected Type TRANSPARENCY for Trans- parency - Tray 3 LTRAY4SENSEDTYPE Detected Type PAPER for Paper - Tray 4...
Page 163 Table 3-4: Printer Unique Variables for Both Printer Languages (Continued) Variable Function LTRAY2PAPERTYPE Tray 2 Paper Type LTRAY3PAPERTYPE Tray 3 Paper Type LTRAY4PAPERTYPE Tray 4 Paper Type LTRAY5PAPERTYPE Tray 5 Paper Type LTRAY1RENUMBER Tray 1 Renumber 3-47 Selections PLAIN, COATED, GLOSSY, PHOTO,...
Page 164: Common Variables For Pcl Emulation
(DEFAULT only) Common Variables for PCL Emulation Note: The word common applies to those variables common to both your printer and the Hewlett-Packard Company’s LaserJet printers. Use these variables only for PCL emulation. The parameter should be specified as To determine which variables your printer supports, see “Table B-3: Common...
Page 165 Printer Unique Variables for PCL Emulation The following variables are unique to your printer and are supported in PCL emulation only. The For example: To determine which variables your printer supports, see “Table B-4: Printer Unique Variables for PCL Emulation” on page B-12.
Page 166 Table 3-6: Printer Unique Variables for PCL Emulation (Continued) Variable Function LASSIGNTRAY1 Tray Renumber Assign Tray 1 LASSIGNTRAY2 Tray Renumber Assign Tray 2 LASSIGNTRAY3 Tray Renumber Assign Tray 3 LASSIGNTRAY4 Tray Renumber Assign Tray 4 LASSIGNTRAY5 Tray Renumber Assign Tray 5...
Page 167: Common Variables For Postscript Emulation
Font Priority Search (SET only) Common Variables for PostScript Emulation Note: The word common applies to those variables common to both your printer and the Hewlett-Packard Company’s LaserJet printers. Use these variables only for PostScript emulation. The parameter should be specified as To determine which variables your printer supports, see “Table B-5: Common...
Page 168 The following variables are unique in some printers and are supported in PostScript emulation only. For example: To determine which variables your printer supports, see Table B-6 on page B-13. Table 3-8: Printer Unique Variables for PostScript Emulation Variable Function LPICTUREGRADE™...
Page 169 To determine which variables your printer supports, see “Table B-7: Printer Unique LRESOURCE Variables” on page B-14. Table 3-9: Printer Unique LRESOURCE Variables Variable Function LDESCRIPTION Macro or Symbol Set Description (DEFAULT only) LRWLOCK Read/Write Lock (password) for an (DEFAULT...
Page 170: Status Readback Commands
Status Readback Commands Applications can request configuration and status information from the printer using the Status Readback commands. In addition, the printer can also be instructed to send unsolicited status information back to the host computer when asynchronous events occur, such as a memory error or a paper jam.
Page 171: Echo Command
The The supported variables are listed in the tables beginning on page 3-12. This printer returns a ? for inquiries of an unsupported variable, or inquiries of a variable associated with an option that is not installed.
Page 172: Info Command
The ECHO command is terminated by the line feed character. INFO Command The INFO command is used to query status information from the printer. “Table 3-10: INFO Category Parameter Values” on page 3-56 lists the categories of information that can be queried.
Page 173 INFO CONFIG Response Syntax (An Example): @PJL INFO CONFIG<CR><LF> IN TRAYS [2 ENUMERATED]<CR><LF> INTRAY1<CR><LF> INTRAY2<CR><LF> MANUAL FEED<CR><LF> OUT TRAYS [1 ENUMERATED]<CR><LF> UPPER FACEDOWN<CR><LF> PAPERS [13 ENUMERATED]<CR><LF> LETTER<CR><LF> LEGAL<CR><LF> A4<CR><LF> A5<CR><LF> B5PAPER<CR><LF> EXECUTIVE<CR><LF> COM10<CR><LF> COM9<CR><LF> MONARCH<CR><LF> DL<CR><LF> C5<CR><LF> B5<CR><LF> OTHERENVELOPE<CR><LF> LANGUAGES [1 ENUMERATED]<CR><LF> PCL<CR><LF>...
Page 174: Is Used For Variables Specific For Postscript Emulation
The variables supported are listed in the tables beginning on page 3-12. • in the tables “Common Variables for Both Printer Languages” on page 3-12, and “Printer Unique Variables for Both Printer Languages” on page 3-19. •...
Page 175: This Printer Returns A ? For Inquiries Of An Unsupported Variable, Or Inquiries Of A Variable Associated With An Option That Is Not Installed
The supported variables are listed in the tables beginning on page 3-12. This printer returns a ? for inquiries of an unsupported variable, or inquiries of a variable associated with an option that is not installed. USTATUS Command This command is used to enable and disable unsolicited status from the printer.
Page 176: Ustatusoff Command
PJL parser. Disables unsolicited status for device changes. Enables unsolicited status for job changes. The printer sends a status message when a job begins and ends. Disables unsolicited status for job changes. Enables unsolicited status for page changes. The printer sends a status message when a printed sheet reaches the standard output bin.
Page 177: Status Message Format
Ready 10001 RDYMSG 10006 88 Ink Low 10002 Not Ready 10002 Not Ready 10005 Resetting the Printer 10006 88 Toner Low 10006 88 Yellow Toner Low 10006 88 Magenta Toner Low 10006 88 Cyan Toner Low 10006 88 Black Toner Low...
Page 178 Table 3-12: PJL Information Messages Printer State Ready with Replace Transfer Power Saver with Ink Low Power Saver mode with Toner Low Power Saver mode with Replace Toner Power Saver mode with Replace PC Kit Power Saver mode with Replace Fuser...
Page 179: Auto-Continuable Conditions
Auto-continuable messages are returned in this form: CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status To determine which messages your printer supports, see “Table B-10: PJL Messages for Auto-Continuable Conditions” on page B-15. Table 3-13: PJL Messages for Auto-Continuable Conditions Printer State...
Page 180 Intervention required: standard parallel port disabled Intervention required: resolution reduced Intervention required: print jobs on disk request Intervention required: printer powered off, disk installed with Print and Hold jobs on the disk Intervention required: short paper Intervention required: flash full...
Page 181 Table 3-13: PJL Messages for Auto-Continuable Conditions (Continued) Printer State Intervention required: unformatted disk Intervention required: scheduled maintenance Intervention required: resource save off deficient memory Intervention required: insufficient collation area Intervention required: hole punch box full Intervention required: hole punch box full...
Page 182 Table 3-13: PJL Messages for Auto-Continuable Conditions (Continued) Printer State Intervention required: flash full Intervention required: disk full Intervention required: disk corrupted Intervention required: too many flash options installed Intervention required: unformatted flash Intervention required: unformatted disk Intervention required: unsupported disk format...
Page 183: Attendance Conditions
CODE=status code DISPLAY=display string (in double quotes) ONLINE=online status To determine which messages your printer supports, see “Table B-11: PJL Messages for Attendance Conditions” on page B-20. Table 3-14: PJL Message for Attendance Conditions Printer State...
Page 184 For this message, the values for XXXX are returned to indicate which ink cartridges are defective. <d> represents a one-letter designator for each door labeled on the printer. <c> represents a one-letter designator for each cover labeled on the printer.
Page 185 For this message, the values for XXXX are returned to indicate which ink cartridges are defective. <d> represents a one-letter designator for each door labeled on the printer. <c> represents a one-letter designator for each cover labeled on the printer.
Page 186 For this message, the values for XXXX are returned to indicate which ink cartridges are defective. <d> represents a one-letter designator for each door labeled on the printer. <c> represents a one-letter designator for each cover labeled on the printer.
Page 187 For this message, the values for XXXX are returned to indicate which ink cartridges are defective. <d> represents a one-letter designator for each door labeled on the printer. <c> represents a one-letter designator for each cover labeled on the printer.
Page 188: Operator Intervention - Paper Handling
For this message, the values for XXXX are returned to indicate which ink cartridges are defective. <d> represents a one-letter designator for each door labeled on the printer. <c> represents a one-letter designator for each cover labeled on the printer.
Page 189 For more information, see “Table 3-16: Tray Values” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Values” on page 3-74. * See your printer See your printer documentation for more information on printer messages. 3-73...
Page 190 Table 3-16: Tray Values X Value Tray Multipurpose Feeder Manual Feed Tray 1 Tray 2 Envelope Feeder Tray 3 Tray 4 Tray 5 Table 3-17: Media Size Values YY Value Media Size Universal Other Envelope Letter Paper Legal Paper A4 Paper Executive Paper 11 x 17 (Ledger) Com 10 Envelope...
Page 191: Operator Intervention - Paper Jams
Media Size Folio Statement Com 9 Envelope Output Bin Standard Bin Bin 1 Bin 2 Bin 3 Bin 4 Bin 5 Bin 6 Bin 7 Bin 8 Bin 9 Bin 10 message appears on the printer operator panel display or...
Page 192 To determine which messages your printer supports, see Table B-13 on page B-28. Table 3-19: PJL Messages for Paper Jams Printer State Intervention required: paper jam Intervention required: paper jam Intervention required: paper jam Intervention required: paper jam Intervention required:...
Page 193 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * See your printer documentation for more information on printer messages. 3-77 Status Code Display String*...
Page 194 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * See your printer documentation for more information on printer messages. 3-78 Status Code Display String*...
Page 195 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number. * See your printer documentation for more information on printer messages. 3-79 Status Code Display String*...
Page 196: Service Errors
* See your printer documentation for more information on printer messages. Service Errors Error Code 50000 is returned for all 9xx Service Errors when the printer can return a status code. To determine whether your printer supports returning service messages, see “Table B-14: Service Errors”...
Page 197: Opmsg Command
When an OPMSG command is received, the message appears and is allotted both lines of the display. The printer is taken OFFLINE. This message, along with the STMSG command, is the lowest priority, so if another intervention occurs, it displays instead.
Page 198: Unique Pjl Commands
Unique PJL Commands To determine which commands your printer supports, see “Table B-16: Lexmark Unique PJL Commands” on page B-34. LBEEP Command This command causes the printer to beep three times. Syntax: LPORTROTATE Command This command causes the printer to rotate ports at the next job boundary. The information to rotate ports is specified in the job header.
Page 199 For example, at the factory, the printer uses 0x1B (character <Esc>) for the escape character. If CHAR = 65 is specified with this command, the printer uses 0x41 (character ‘A’) as the escape character for the host interface port specified via the PORT parameter.
Page 200 parameter The following ports are valid parameters for LESCAPECHAR: • • INA1 • INA2 • INA3 • LOCALTALK1 • LOCALTALK2 • LOCALTALK3 • PARALLEL • PARALLEL1 • PARALLEL2 • PARALLEL 3 • • USB1 • USB2 • USB3 • SERIAL •...
Page 201 This command tells the printer that the output resulting from the current job is being sent to the fax processing device instead of to the printer. The current job is printed and is not sent to the fax processing device if one of the following occurs: •...
Page 202: File Commands For Flash Or Disk
LDOWNLOADTARGET Command This command specifies which device is the target for downloaded files. The target can be RAM, flash, or disk. Syntax: File Commands for Flash or Disk Use the following commands to manage resources on flash and disk devices: •...
Page 203 Table 3-22 lists the parameters used with most of the commands. Additional parameters are noted in the description of each command. Table 3-22: Variables for Flash and Disk File and Password Commands Parameter Syntax ACCESS = LENGTH = 3-87 Description One of the following access types must be specified when a file is opened: Open for read only.
Page 204 Table 3-22: Variables for Flash and Disk File and Password Commands (Continued) Parameter Syntax DEVICE = DEVICE = FILENAME = "fname" OLDFILENAME = "fname" NEWFILENAME = "fname" 3-88 Description File storage media. Case insensitive. value is used for the LRUNFILE command only. Note: The command is ignored if the device is not installed.
Page 205 Table 3-22: Variables for Flash and Disk File and Password Commands (Continued) Parameter Syntax START = Note: If PostScript emulation is used to create the file on the device, it may automatically attach a Extensions” on page 6-10 for more information. For example, if downloaded to flash through PostScript emulation, the commands is LOPENFILE Command...
Page 206 LREADFILE Command Use this command to read data from a file on a storage device. Syntax: Response Syntax: Notes: • The file must be closed using the LCLOSEFILE command once all operations are complete. • The command is ignored if the file doesn’t exist on the device or has not already been opened with LOPENFILE with an •...
Page 207 LWRITEFILE Command Use this command to write data to a file on a storage device. Syntax: Notes: • The file must be closed using the LCLOSEFILE command once all operations are complete. • The command is ignored if the file doesn’t exist on the device. The command is ignored if the file isn’t already open with a write •...
Page 208 LRENAMEFILE Command Use this command to rename a file on a storage device. The command is ignored if the filename specified as OLDFILENAME doesn’t exist on the device, or if the filename specified as NEWFILENAME already exists on the device. Syntax: LDELETEFILE Command Use this command to delete a file on a storage device.
Page 209: File And Device Protection Commands
File and Device Protection Commands The following information applies to password protection. • You can set both read/write and write passwords for a resource. If both passwords are set, the read/write password has precedence over the write password. • If you attempt to password-protect a non-existing resource, the PJL interpreter will return a warning (CODE = 25001).
Page 210 @PJL DEFAULT LRESOURCE:" LRWLOCK=" Note: If the filename is incorrect, the printer applies the password to the entire device. Password for an Entire Device If you want to set a password on a device, not just a single file, omit the filename.
Page 211: Unlocking A Protected File Or Device
The file or device is not automatically re-locked with the EOJ command. Syntax: Values for " See “Printer Unique LRESOURCE Variables” on page 3-52 for information about values for Note: This should be the same password that was defined in the DEFAULT command.
Page 212: Re-Locking A Protected File Or Device
Re-Locking a Protected File or Device Use the LDELETEPASSWORD command to re-lock a password-protected file or device that has been unlocked using the LDECLARE command. If an LRESOURCE is not specified, all unlocked files or devices are re-locked. Syntax: Values for " 3-96 "...
Page 213: Unlocking A Protected File Or Device For The Current Job
Unlocking a Protected File or Device for the Current Job The file or device unlocked by the execution of this command is automatically re-locked upon execution of the EOJ command or by a printer language change. Syntax: Values for "...
Page 214: Recovering Lost Passwords
Syntax: Use the following steps to retrieve lost passwords: Send the LQUERYSEED command to the printer by one of the host computer interfaces. This command causes a value, the “seed,” to display on the printer operator panel, through MarkVision Professional or, if there isn’t an LCD panel, to print on the Menu Settings Page.
Page 215: Postscript Emulation
Selecting PostScript Emulation Using SmartSwitch When SmartSwitch is enabled for both printer languages on an interface, the printer automatically switches to the printer language being sent by your software program. The printer is shipped with SmartSwitch enabled for both printer languages and all interfaces.
Page 216: Using Your Software Program
297 x 914 The Lexmark C510(n) supports this size media only with an optional legal tray. B5 is a Japanese Industry Standard (JIS) paper size. The same B5 designation is used by JIS and International Standards Organization (ISO) for different paper sizes.
Page 217 Error: stackoverflow setignoresize overrides the automatic page orientation selected by the printer to support custom media sizes. This operator determines whether or not to adjust the text based on the page size. value may be:...
Page 218: Paper Tray Support
Error: rangecheck, stackunderflow, typecheck Paper Tray Support When the printer receives one of the operators listed in “Table 4-2: Tray Selected with Tray Operators” on page 4-6, it performs the actions listed as follows. This paper tray selection process ends as soon as a suitable paper source is chosen and paper is fed from this tray.
Page 219 • If the requested media size is not found by the previous search, the following search order is used: – Tray 1 – Tray 2 – Tray 3 – Multipurpose Feeder – Tray 4 – Tray 5 • If the requested size cannot be located in any automatic source, a configurationerror is issued and the job is flushed.
Page 220 11x17tray tray with 11 x 17-size paper PostScript Printer Models W840...
Page 221 manualfeed in statusdict indicates if a manual feed source has been selected. The boolean value can be: prints from a manual feed source (default) prints from an automatic feed source This boolean key can be redefined to affect manual feed for the current job. If the value of the manualfeed operator or the ManualFeed page device parameter is when showpage or copypage is executed, the page is fed...
Page 222 • If a setpapertray operator is issued for the back of a duplexed page, the printer ejects a blank back page, changes the paper source, and prints the information for the back side of the page on the front side of a page from the new paper source.
Page 223: Envelope Size Support
104.8 x 241.3 4.125 x 9.5 [297 684] 110 x 220 4.33 x 8.66 [312 624] 162 x 229 6.38 x 9.01 [459 649] 176 x 250 6.93 x 9.84 [499 708] Other [612 996] Other [841 842] PostScript Printer Models W840...
Page 224 Note: Duplexing is not supported on any envelope size. If duplex printing is requested and one of the envelope size operators is sent to the printer, duplexing is suspended until a paper size is requested that is supported for duplex printing.
Page 225: Envelope Tray Support
If the size is still not available, a configurationerror is issued and the print job is flushed. If manualfeed or ManualFeed is size manually. If no manual feed exists on the printer, a rangecheck error message is generated. The envelope tray the printer selects when it receives an envelopetray operator is listed in Table 4-5.
Page 226 3.875 x 7.5 size envelopes 3.875x8.875envelopetray tray with 3.875 x 8.875 size envelopes 4.125x9.5envelopetray tray with 4.125 x 9.5 size envelopes com10envelopetray tray with 4.125 x 9.5 size envelopes otherenvelopetray tray with other size envelopes 4-12 PostScript Printer Models W840...
Page 227: Supplemental Operator Summary
When you define it outside the normal server loop, it is reset to the default value when the printer is switched to a printer language other than PostScript emulation or when a power-on reset occurs.
Page 228 A specified password matches either password. The boolean value can be: correct password incorrect password After the is returned, the printer waits 1 second before it continues processing. Errors: stackunderflow, typecheck Note: The password is defined as a 4-byte number.
Page 229 (default) seconds • ManualFeedTimeout page device parameter disabled seconds (default is device dependent) To find the default for your printer, see Table C-2 on page C-5. • WaitTimeout system parameter disabled seconds (default is 40 seconds) Error: stackoverflow deletefile deletes the specified file from the disk.
Page 230 devcontrol allows a host computer utility to manage resources on the flash or disk. It requires a string device name parameter, an integer command name parameter, and two command argument parameters. The device control operator performs a specified command on the specified device. The return values on the stack indicate: the command is successful the command is unsuccessful and returns an error code...
Page 231 Table 4-7: Unsuccessful devcontrol Parameter Error Codes Code Meaning File system access has not been initialized Could not allocate file descriptor Some invalid argument was passed No such device Invalid access to file requested Argument too large (filename, buffer) Invalid file descriptor or filename Catch all error or device error Unable to allocate memory for buffer, data structure Device busy...
Page 232 devforall executes the specified procedure for each storage device after pushing a substring on the stack that is the portion of the scratch string containing the device name. This operator is in systemdict. Errors: invalidaccess, rangecheck, stackoverflow, stackunderflow, typecheck, undefined devformat formats (erases all data from) the specified device.
Page 233 devmount sets the Mounted device parameter for the specified device to returns the value of the Mounted device parameter for the specified device. This operator is in systemdict. The boolean values indicate: device successfully mounted, or was already mounted device not mounted If a device with the specified device name is not installed, an undefinedfilename error occurs.
Page 234 , if the device is mounted. This value is the same as the Mounted device parameter from the specified IODevice. , if the device is removable and must be mounted before it is referenced. This value is the same as the Removable device parameter from the specified IODevice.
Page 235 diskstatus returns on the stack the following two integers: • Number of pages that are free on the optional disk. The value of the Free device parameter from the %disk1% IODevice. • Total number of pages (1024 bytes) that are on the optional disk. The value of the LogicalSize device parameter from the %disk1% IODevice.
Page 236 This operator is equivalent to executing the following PostScript emulation sequence: currentpagedevice /PostRenderingEnhanceDetails get /REValue get Error: stackoverflow 4-22 PostScript menu item. A boolean value Jam Recovery is set to ) (default) Jam Recovery is set to Jam Recovery printer setting. The Print PS Error...
Page 237 dostartpage returns a boolean with the same value as the system parameter DoStartPage. The DoStartPage system parameter must be present for the compatibility operator dostartpage to be present. Error: stackoverflow dosysstart returns the current value of the StartupMode system parameter. A boolean value is returned: StartupMode set to 1 or 11 StartupMode other than 1 or 11...
Page 238 This operator is equivalent to executing the following PostScript emulation sequence: currentpagedevice /Duplex get Error: stackoverflow enginesync indicates if the printer waits for the last page of a job to print before returning a Ctrl-D to the host computer. Error: stackoverflow 4-24 PostScript...
Page 239 file creates a file object with specified filename and access. The open the file for reading only create a file if one does not already exist, or truncate and overwrite it if it does exist. File is opened for writing only. create a file if one does not already exist or append it if it does exist.
Page 240 firstside indicates whether the current imaging area is on the front side of the page. front side is currently being imaged back side is currently being imaged Error: stackoverflow fontnonzerowinding sets the winding rule for Type 1 fonts. No query operation is performed since the winding rule is reset to at the beginning of each print job.
Page 241 ignoresize See page 4-3. initializedisk initializes the disk with the page count and action as integer arguments. The arguments set the (%disk1%) IO device parameters as follows: • LogicalSize parameter is set to • If a value of 0 is set as •...
Page 242 jobsource indicates the current value of the CurInputDevice system parameter. A string is returned on the stack indicating the job source. Valid values are: %LocalTalk% %SerialA% %SerialB% %SerialC% %SerialD% %ParallelA% %ParallelB% %ParallelC% %ParallelD% %IR_A% %IR_B% %IR_C% %IR_D% %USB_A% %USB_B% %USB_C% %USB_D% %EtherTalkB% %EtherTalkC%...
Page 243 %LPR_B% %LPR_C% %LPR_D% %UnknownDevice% This operator is equivalent to executing the following PostScript emulation sequence: currentsystemparams /CurInputDevice get Error: stackoverflow jobtimeout queries the current user default setting for the JobTimeout parameter. An integer is returned on the stack: disabled seconds This operator is equivalent to executing the following PostScript emulation sequence: currentuserparams /JobTimeout get...
Page 244 manualfeedtimeout is an integer key in statusdict that works with the ManualFeedTimeout page device parameter to determine the manualfeed timeout for a given page. If during a print job, statusdict, that value is used instead of the ManualFeedTimeout page device parameter.
Page 245 PrinterName system parameter that is defined by the operator. The value of the string defines the printer name. A maximum of 32 characters are returned on the stack. This operator is equivalent to executing the following PostScript emulation...
Page 246 Number of minutes elapsed after last page prints before Power Saver is invoked. Power Saver reduces power consumption when the printer is idle. When enabled, it takes longer to print the first page after the printer has been idle. 4-32 (Antique Olive Roman)
Page 247 Note: Some printer models released in the year 2000 or later designated as Energy Star printers cannot have Power Saver disabled. This operator is equivalent to executing the following PostScript emulation sequence: currentpagedevice /PowerSave get Error: stackoverflow ramsize queries the current setting of the RamSize system parameter. An integer is returned on the stack showing total RAM in bytes.
Page 248 resolution queries the resolution for the current print job. An integer is returned on the stack: 300 dpi is set to On 600 dpi is set to On 1200 dpi is set to On This operator is equivalent to executing the following PostScript emulation sequence: currentpagedevice /HWResolution get 0 get Error: stackoverflow...
Page 249 If only one serial interface port is available on the printer, both the same values. Baud and option values are returned on the stack. returns the value of the...
Page 250 sccinteractive provided for parsing compatibility purposes. A value of Errors: invalidaccess, rangecheck, stackoverflow, stackunderflow, typecheck setcoverpage specifies a cover page for a fax job. The default value is values indicate: the current page that is processing is moved to the first page of the current fax job the current page that is processing is unaffected Errors: stackunderflow, typecheck...
Page 251 Off Print PS Error Errors: invalidaccess, stackunderflow, typecheck 4-37 PostScript menu item. The changes Jam Recovery is set to On) Jam Recovery is set to Off or Auto Jam Recovery . It also printer setting. The Print PS Error...
Page 252 setdoret changes the PQET setting for the next page through the end of the print job. The integer values allowed are: turn PQET Off turn PQET On turn PQET On turn PQET On turn PQET On The value you select for PQET returns to the user default setting when the print job is finished.
Page 253 StartupMode set to 1 StartupMode set to 0 (default) • If , the printer executes a Sys/Start file from flash or disk when the PostScript emulation interpreter is initialized. If no flash or disk is installed, no action occurs. • If a Sys/Start file is on both flash and disk, the search order for the devices determines which one is executed.
Page 254 Ctrl-D to the host computer. The boolean values indicate: printer waits for the last page of the job to print...
Page 255 setfileposition moves the read pointer in an open file to the new specified file position. This is defined as the number of bytes from the start of the file. The next read operation starts at the new file position. This operator is in systemdict. Errors: ioerror, stackunderflow, typecheck, undefinedfilename Note: An undefinedfilename error occurs if the file does not exist.
Page 256 While printing the second sides the printer’s available paper sources are restricted to the automatic tray (tray1) and the manual paper feeder for the remainder of the job or until the manual duplex mode value is changed.
Page 257 Any changes made by this operator are not active until the end of the print job. Note: Some printer models released in the year 2000 or later designated as Energy Star printers cannot have Power Saver disabled. This operator is equivalent to executing the following PostScript emulation...
Page 258 • The printer waits for the paper path to clear before changing the resolution. • If the resolution is changed for the back side of a duplexed sheet, the printer ejects a blank back page, changes the resolution, and prints the information for the page where the resolution was changed on the front side of the next sheet.
Page 259 setsccinteractive supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed, and three integers are removed from the stack and discarded. Errors: invalidaccess, rangecheck, stackunderflow, typecheck setsoftwareiomode supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed, and an integer is removed from the stack and discarded.
Page 260 setuserdiskpercent removes an integer from the stack and discards it. Errors: stackunderflow, rangecheck, invalidaccess, typecheck softwareiomode supports compatibility with the IBM LaserPrinters 4019, 4029, and 4039. It is parsed and returns a (zero, Binary Mode Off) on the stack. Software IO mode defines the data stream you are using. Errors: stackoverflow, stackunderflow tumble returns the current value of the Tumble page device parameter.
Page 261 userdiskpercent returns a (zero) on the stack. Errors: stackoverflow, invalidaccess waittimeout queries the current value for the WaitTimeout user parameter. An integer is returned on the stack: disabled seconds This operator is equivalent to executing the following PostScript emulation sequence: currentuserparams /WaitTimeout get Error: stackoverflow 4-47...
Page 262: Page Device Parameters
1, 2, 3, 1, 2, 3. The non-collated output is 1, 1, 2, 2, 3, 3. Determines if the printer uses the printer’s own internal algorithms or Adobe PostScript algorithms to select print media. The following values are supported: True Uses the printer’s algorithms...
Page 263 Optra C710, Optra M410, Optra T family, and Optra W810. PictureGrade is an integer that provides compatibility with previous Lexmark printer drivers. PictureGrade works in conjunction with Screening. If Screening is set to None or PictureGrade, the values for PictureGrade affect...
Page 264 InputAttributes dictionary in the pagedevice dictionary. True MediaType entries in the InputAttributes dictionaries cannot be modified by the user. The values are confined to values known by the printer operating system. False MediaType entries in the InputAttributes dictionaries can be modified by the user.
Page 265 4-51 Definition Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-5. ColorCorrection is a null, string, or name object that controls the appearance of colors. The value is determined by the user default setting in the menu item.
Page 266 Table 4-8: Page Device Parameters (Continued) Type ImagingBBox array or null InputAttributes dictionary 4-52 Definition Defines a rectangle that lies within the boundaries of the page specified by PageSize. ImagingBBox may be either a value of null or an array of four numbers. A value of null indicates the bounding box is the largest imageable area possible for a given page size.
Page 267 Mode is a key within the InputAttributes dictionary, and its value is a name that determines the mapping of the physical input sources to the input sources listed in InputAttributes. The allowable values are: /Default Printer’s default source assignment /Optra Specifies the following ordering used in InputAttributes: 0 - Tray 1...
Page 268 ManualFeed is set to True. If the default paper source is not a manual paper source, ManualFeed is set to False. Indicates the amount of time that the printer waits for you to manually load a sheet of paper.
Page 269 Orientation determines the positioning of multiple page images on pages printed using NupDetails. You may choose one of four different orders. The positioning of page images depends on whether they are sent to the printer as portrait or landscape images. The following examples show the result of using each setting...
Page 270 RV The first page is placed at the upper right corner of the printed page and subsequent pages are placed down and then across. Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-5.
Page 271 Table 4-8: Page Device Parameters (Continued) Type OutputAttributes dictionary OutputPage boolean OutputType string PageDeviceName string name or null 4-57 Definition Contains information about the output bin targets. There is a numeric key, which is a dictionary, for each installed output bin. OutputType and OutputLocation are the allowable keys in each output dictionary.
Page 272 Disable media selection. Implement the requested PageSize on the previously selected media without making adjustments. The way the image is positioned on the media is printer-dependent and may result in part of the image being clipped. If the SubstituteSize parameter from the DeviceRenderingInfo...
Page 273 1 to 4 is On (default is 1). PQET Type is a constant value. To find the value of Type for your printer, see “PostRenderingEnhanceDetails” on page C-8. A value of 1–120 or 1–240 (model specific) indicates the number of minutes that elapses after the last page prints and before the Power Saver feature is invoked.
Page 274 The key is found in the DeviceRenderingInfo dictionary within pagedevice. It can be altered using a setpagedevice operator. Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-5. Specifies whether to staple the current print job.
Page 275 Causes pages to print as if they are to be side bound (as in a book) Controls the variable Universal paper size feature. The entries are as follows: Type is a constant value. To find the value of Type for your printer, see Table C-2 on page C-5.
Page 276: Interpreter Parameters
If a setuserparams value does not match the type of the specified parameter, a typecheck error occurs. If a parameter is not supported by the printer, it is ignored. An attempt to change the value of a read-only parameter has no effect on the parameter.
Page 277 Maximum number of bytes occupied by the pixel array of a single character in the font cache. There is an upper limit dependent on the MaxFontCache system parameter and the amount of printer memory. Legal values: Any non-negative integer. Maximum number of bytes occupied by a single cached form.
Page 278 Note: This value is reset to 0 (zero) during PostScript initialization. Since PostScript initialization by the printer cannot be known, we recommend querying the value of PageCount at the beginning of a job and at the end of a job, and then calculating the difference to determine how many pages are submitted to the printer for a specific job.
Page 279: System Parameters
CurFormCache integer These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 280 DisableFastProcs integer These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 281 GenericResourcePathSep string These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 282 MaxScreenStorage integer These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 283 StaticRamSize integer These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 284 WaitTimeout integer These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 2016. These parameters are available with the Adobe PostScript Language Supplement 3010. These parameters are Lexmark-specific and are in addition to the Adobe PostScript Language Supplement 3010.
Page 285: Device Parameters
For additional information on flash memory and disk, see Chapter 6: “Flash Memory and Disk” on page 6-1. To determine which devices your printer supports, see Table C-5 on page C-14. To determine which device parameters your printer supports, see Table C-6 on page C-16.
Page 286 Device Parameters for the Communication Device %Parallel%, %ParallelA%, %ParallelB%, %ParallelC%, %ParallelD% (%Parallel_NV% and %Parallel_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean...
Page 287 DataBits integer Returns the value of the DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only) Supported values are:...
Page 288 Supported values are: SerialMode name Designates the serial communication configuration: RS232C or RS422. Returns the value of the Serial Returns RS232 on a printer that is attached with a cable that does not support RS-422. 4-74 PostScript AutoSelect PPDS True Data is sent and processed.
Page 289 Device Parameters for the Communication Device %LocalTalk%, %LocalTalkA%, %LocalTalkB%, %LocalTalkC%, %LocalTalkD% (%LocalTalk_NV% and %LocalTalk_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 290 Device Parameters for the Communication Device %EtherTalk%, %EtherTalkA%, %EtherTalkB%, %EtherTalkC%, %EtherTalkD% (%EtherTalk_NV% and %EtherTalk_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 291 Device Parameters for the Communication Device %IR%, %IR_A%, %IR_B%, %IR_C%, %IR_D% (%IR_NV% and %IR_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. 4-77 InterpreterBased...
Page 292 Device Parameters for the Communication Device %USB%, %USB_A%, %USB_B%, %USB_C%, %USB_D% (%USB_NV% and %USB_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: 4-78 True False...
Page 293 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition Enabled boolean (Read-only) Supported values are: Filtering name Indicates if the input needs further filtering before the data can be correctly processed. Supported values are: HasNames boolean (Read-only) Always returns False. Interpreter name (Read-only)
Page 294 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only) Supported values are:...
Page 295 Device Parameters for the Communication Device %AppSocket%, %AppSocketA%, %AppSocketB%, %AppSocketC%, %AppSocketD% (%AppSocket_NV% and %AppSocket_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 296 Device Parameters for the Communication Device %RemotePrinter%, %RemotePrinterA%, %RemotePrinterB%, %RemotePrinterC%, %RemotePrinterD% (%RemotePrinter_NV% and %RemotePrinter_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 297 Device Parameters for the Communication Device %PrintServer%, %PrintServerA%, %PrintServerB%, %PrintServerC%, %PrintServerD% (%PrintServer_NV% and %PrintServer_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 298 Device Parameters for the Communication Device %LexLink%, %LexLinkA%, %LexLinkB%, %LexLinkC%, %LexLinkD% (%LexLink_NV% and %LexLink_Pending% contain the same parameters) DelayedOutputClose boolean Selects how the printer manages the port at the end of each print job. Supported values are: This value is set independently for each port. Enabled boolean (Read-only)
Page 299 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition HasNames boolean (Read-only) Always returns False. Interpreter name (Read-only) Supported values are: boolean Designates if the communication channel is On and able to receive and send data. Supported values are: PortLocation string (Read-only) Designates the physical location of the port related to the parameter set.
Page 300 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition Device Parameters for the Parameters Device %EthernetPhysical%, %EthernetPhysicalA%, %EthernetPhysicalB%, %EthernetPhysicalC%, %EthernetPhysicalD% EthernetAddress string (Read-only) boolean Designates if the communication channel is On and able to receive and send data. Supported values are: PortLocation string (Read-only) Designates the physical location of the port related to the parameter set.
Page 301 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition Darkness real Print Darkness and Toner Saver Setting Designates the print darkness and toner saver setting (model specific). Legal value: Any non-negative real number from 0.0 to 1.0, inclusive. For queries, the Print Darkness setting is returned as a real value: When the Darkness value is changed, the following ranges determine the Print Darkness and Toner Saver setting values: Print Darkness Setting...
Page 302 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition PageCount integer (Read-only) Page Count TimeToStandby integer Power Saver. Supported values are: 0 to 120, in minutes Type name (Read-only) Always returns the value of /Parameters. Device Parameters for the Parameters Device %Console% Language name Display Language...
Page 303 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition InitializeAction integer Specifies an action for initializing the disk. Supported values are: Note: The current file system refers to /FileSystem. See Type as follows for more information. LogicalSize integer Specifies the size of the file system to be created and is as an argument by InitializeAction. •...
Page 304 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition HasNames boolean (Read-only) Indicates if the flash parameter is only valid when flash is mounted (mounted is set to True). If flash is not mounted, the parameter has a value of False. InitializeAction integer Specifies an action for initializing flash:...
Page 305 Table 4-11: PostScript Emulation Device Parameters (Continued) Type Definition Device Parameters for the IODevice %rom% BlockSize integer (Read-only) Free integer (Read-only) Indicates the amount (in pages) of free space available in ROM. Valid only if the ROM is mounted (mounted is set to True). A value of 0 (zero) indicates that either the ROM is not mounted or it is full.
Page 306: Status And Error Messages
The printer is idle and another interpreter is the selected interpreter. Notes: • Status queries cannot be received while the printer is in an error state. • Your printer always selects the PostScript emulation interpreter and pro- cesses a Ctrl+T (x'14') command as a status query when data is received through the LocalTalk interface.
Page 307: Status Messages
Status Messages Your printer responds to a Ctrl+T (x'14') status query on an interface by sending a one-line status message back to the host computer over the same interface. If the status query is received between print jobs and the printer is idle with no error conditions, an idle response is returned to the host computer.
Page 308 4-94 PostScript...
Page 309: Switching Languages
Consequently, the printer examines all print jobs coming into all its interfaces and switches between PostScript emulation and PCL emulation dynamically. If a software program explicitly tells the printer which language to use by a PJL command, the printer always accepts and uses that explicit command, regardless of how SmartSwitch has been set from the printer operator panel.
Page 310: Setting Smartswitch For Different Interfaces
Setting SmartSwitch for Different Interfaces You can customize your printer so that particular print jobs are sent to particular interfaces. For example, you may want to send all PostScript emulation jobs to the network interface and all PCL emulation jobs to the parallel interface. You can do so...
Page 311: Sniffing
Disabled when a SIC or PJL command within a valid printer language is received. The printer examines the received data stream, attempts to determine the type of data stream, and automatically switches to the proper language. The printer examines the active printer language and decides when an End-of-Job point occurs.
Page 312: Flash Memory And Disk
See your printer documentation for more information. When first installed in the printer, the flash memory or disk may be unformatted. You must format the device before you download resources. A message displays on the printer operator panel or through MarkVision Professional if the device is unformatted.
Page 313: Resource Data Collection (Download Target)
The operator panel menus to select • The MarkVision Professional printer utility. You can also download resources to flash memory and disk or format the flash memory or disk using this printer utility. • A PJL command (see “LDOWNLOADTARGET” on page 3-30 and “LDOWNLOADTARGET Command”...
Page 314: Storing Resources On Flash Memory Or Disk
• PCL emulation collects and stores the currently defined font, macro, or symbol set information in printer RAM memory. These resources are written to flash memory or disk when Resource Data Collection is disabled (see step 3). Stored resources are also copied to flash memory or disk when a printer language switch occurs.
Page 315: Part Name
Part Name Part Name as it is stored in the flash memory card header. If flash memory is formatted by the printer, the part name field is shown as FLASH. The part name field for the disk is not printed.
Page 316 Part Number Part Number as it is stored in the flash memory card header. If the flash memory is formatted by the printer, the part number field is shown as (none). The part number field for the disk is not printed.
Page 317 .Mac5 (PCL macro) Except as noted below, file types listed above are recognized by the flash format used in your printer. In addition, the flash format in your printer also recognizes the following formats: .data (user data) - any file written with PostScript operators .type1 (PostScript font) - replaces the earlier .t1 extension...
Page 318: Password Protection
The description field for fonts comes from the font header. The description field for macros or symbol sets is blank unless the description field in the file header is set by the PJL LRESOURCE command. See “Printer Unique LRESOURCE Variables” on page 3-52.
Page 319: Rewriting The Flash Content
0), it cannot be changed back to binary 1 without a complete flash memory format. As PostScript emulation file operators write data to flash memory, the printer microcode software verifies that none of the bits being set to binary 1 is binary 0. If any attempt is made to change a 0 bit back to 1, a PostScript emulation ioerror occurs.
Page 320: Accessing Files With Postscript Emulation
Accessing Files with PostScript Emulation File Naming Conventions For any PostScript emulation operator that requires a filename parameter, the filename can be one of the following: %device%filename Specifically references a file on a particular device. If the filename does not exist on %device%, no other %device% is accessed for a duplicate filename.
Page 321 Device names are case sensitive. They must appear exactly as shown. Each device (except the disk) has one synonym. For example, the flash memory can be referred to as This system allows for future expansion of multiple flash memory or disk devices. The disk device name provides for multiple physical units and multiple logical units.
Page 322 The value of this operator adds the extension .data to all filenames referenced when using PostScript emulation file operators. To prevent the .data extension from being added, issue the following PostScript emulation command: statusdict begin false setfilenameextend To add the .data extension automatically again, issue: statusdict begin true setfilenameextend The following example shows how to remove a file for the font myfont from the disk.
Page 323: Device Search Order
Device Search Order If you are using the PostScript emulation operators run, file, renamefile, status or eexec, you do not need to specify the device. If you omit the device name, devices are searched in the default order: disk and then flash memory. If the following PostScript emulation code is encountered, (myfile) (w) file the file on disk is used (since disk occurs before flash memory in the default search...
Page 324: Performance
Although job buffering is designed for individual workstations and networks using MarkVision Professional as the primary tool to control printer operations, you can handle some job buffering functions from the printer operator panel. See your printer documentation for more details.
Page 325: Creating A Partition
For minimum acceptable job buffering performance, the hard disk should be able to read and write files at a sustained rate of 600Kb/sec. The Lexmark hard disk option supports this requirement. Some advantages of job buffering include: • The printer accepts print jobs more quickly.
Page 326: Disabling Job Buffering
Finally, delete or resize the job buffer partition. Recovering from a Power Loss If the printer loses power, the job being spooled to the disk may be lost. Jobs already stored on the disk remain intact. When power is restored, you are asked if you want to print the jobs held in the buffer.
Page 327: Printer Specifications
CHAPTER 7: Printer Specifications This chapter lists printer specifications and information about hardware, environmental conditions, and power requirements. Airflow Requirement Room should meet ASHRAE 62–1989 standards. Noise Emission Levels The following measurements were made in accordance with ISO 7779 and reported in conformance with ISO 9296.
Page 328: Electrical Specifications
T640, T642, T644 (high voltage model) W840 (low voltage model) W840 (high voltage model) Warning: Lexmark recommends that you do not use voltage converters with printers. Power Requirements The following tables list the nominal average power requirements (including fuser power). Table 7-3 Power Requirements...
Page 329: Physical Specifications
Table 7-3 Power Requirements Printer Model T430/ T430d/T430dn State 100 V 115V 230 V Idle with Power 11 W Saver Rated short term current Note: Power requirements for network models may differ. This value is >19 W for units manufactured after 4/30/2004.
Page 330: Clearance Requirements
Above See Note When installing the printer, the customer should leave enough room to access the paper tray(s), the multipurpose feeder, the left side door and the rear exit door. When installing the MFP, leave enough room to access the paper tray(s), the multipurpose feeder, the left side door, and the rear exit door.
Page 331: Altitude Specifications
Table 7-5: Humidity Ranges Printer Model T430, T430d, T430dn T640, T642, T644 W840 Altitude Specifications Table 7-6: Printer Altitude Specifications Printer Model T430, T430d, T430dn T640, T642, T644 W840 Atmospheric Pressure 74.6–101.3 kPa (560–760 mmHg) Specifications Operating Value Shipping/Storage Value –...
Page 332: Printer Interfaces
Interfaces CHAPTER 8: Printer Interfaces Interfaces connect your printer to other devices, such as a computer. Some Lexmark printers have a standard parallel connector (also referred to as a Centronics-type interface) and/or a USB connector. Some Lexmark printers have an internal print server and a USB connector.
Page 333: Setting Up The Communications Port
COM1 port, then the Communications Port [COM1] Properties screen displays. Click the Port Settings tab. Fill out the fields for the following printer settings to make them match your printer settings: • Bits per second •...
Page 334: Setting Up The Communications Port Using Windows Nt 4.0
The Settings screen for this specific port displays. For example, if you select the COM1 port, then the Settings for COM1 screen displays. Fill out the fields for the following printer settings to make them match your printer settings: •...
Page 335: Setting Up The Communications Port Using Windows 2000
COM1 port, then the Communications Port [COM1] Properties screen displays. Click the Port Settings tab. Fill out the fields for the following printer settings to make them match your printer settings: • Bits per second •...
Page 336: Setting Up The Communications Port Using Windows Xp
COM1 port, then the Communications Port [COM1] Properties screen displays. Click the Port Settings tab. Fill out the fields for the following printer settings to make them match your printer settings: • Bits per second •...
Page 337: Deciding Which Interface To Use
One or more of the following is built into your printer: a standard parallel connector, a USB connector, or a network connector. To use a port, connect a cable from the printer to the computer, then set the appropriate values from the printer operator panel or, for network connected printers only, through MarkVision Professional.
Page 338: Parallel Interface
Parallel Interface Use the Lexmark 3.04 m (10 ft) parallel cable part number 1021231, or a cable that is IEEE 1284 compliant, to connect your printer to a personal computer or to a host system with a Centronics-compatible parallel port. See your printer documentation for the location of the printer parallel connector.
Page 339: Standard Parallel Connector
Variable default paper size settings become the active paper formatting size. • If paper is loaded in a tray with auto size sensing, the printer resets the active default paper formatting size to the size of the paper in the tray.
Page 340 20 feet. Cable lengths greater than 20 feet are not supported. The cable drawing to the left is a functional representation of the Lexmark cables; it does not reflect correct pairing of leads or unused pairs.
Page 341 5 V. Rise and fall times of each signal must be less than 1,500 nanoseconds (ns) without slope reversal. Note: For best results, use the Lexmark 1.83 m (6 ft) parallel cable, part number 11K4078. 8-10...
Page 342 Standard Protocol Data Transfer Sequence The following illustration shows the typical data transfer sequence on the parallel interface. See Table 8-1 for typical parallel interface timings on the parallel interface. DATA1-8 STROBE* BUSY ACK* 8-11 Interfaces...
Page 343 Fastbytes protocol is the printer default. If you have data transmission problems between your personal computer and the printer, change the parallel protocol to Standard. This causes the printer to operate in IEEE-compliant compatibility mode.
Page 344: Printer-To-Computer Communication (Advanced Status)
The optional RS-232C Serial/Parallel 1284-C Interface Card has an IEEE 1284-C compliant connector and is an IEEE 1284-I compliant device. Your printer could be considered an IEEE 1284-II compliant device if the “C” to “B” style connector converter were used. The printer exceeds the maximum allowable circuit capacitance for Level II interfaces.
Page 345: Parallel Mode 1
You can get IEEE 1284 documentation by calling 1-800-678-IEEE (order number DS02709). Parallel Mode 1 Parallel Mode 1 is a feature available for many Lexmark printers. The factory default setting is for the factory default for your printer. If the host side of the parallel interface is using open collector drivers to transmit data...
Page 346: Parallel Mode 2
Parallel Mode 2 Parallel Mode 2 is a feature available for many Lexmark printers. The factory default setting is The timing required by the printer is clearly indicated in “Standard Protocol Data Transfer Sequence” on page 8-11. This is the classic Centronics interface timing.
Page 347 AUTOFD* Receiver for the Lexmark T640x The following diagram illustrates the AUTOFD* receiver for the Lexmark T640x. Connector DATA 1-8 Signal Driver/Receivers for the Lexmark T640x The following diagram illustrates the DATA 1-8 signal driver/receivers for the Lexmark T640x. Connector 8-16 74LVC161284 470 pF ±10%...
Page 348 ACKNLG*, ERROR*, SLCT, PE Drivers for the Lexmark T640x The following diagram illustrates the ACKNLG*, ERROR*, SLCT, PE drivers for the Lexmark T640x. 74LVC161284 BUSY Driver and INIT* Receiver for the Lexmark T640x The following diagram illustrates the BUSY driver and the INIT* receiver for the Lexmark T640x.
Page 349: Using The Rs-232C Serial Interface
Use RS-232C serial interface if the printer is more than 3.04 m (10 ft) from the computer but less than 15.24 m (50 ft) away. (You can also use a 6.1 m (20 ft) Lexmark cable to connect a printer and a computer located up to 20 feet apart.)
Page 350 How to Connect the RS-232C Serial Interface Use Lexmark serial cable P/N 1038693 (15.24 m or 50 ft) to connect the serial interface. RS-232C Serial Cable Pin Assignments The RS-232C serial cable appears as follows: Table 8-3: Dedicated Serial Connector Pin Assignments (RS-232C)
Page 351 IBM designed 9-pin serial port, use a 9-pin to 25-pin cable, such as IBM Part Number 6450242 (254 mm or 10 in.). Null modem cables, such as Lexmark part number 1038693 [15.24 m (50 ft)], will connect the converter cable to the printer. The illustration below represents the 25-pin connectors for the RS-232C cable (1038693).
Page 352 10-bit, 11-bit, and 12-bit data frames and set the serial data transfer parameter so that each data frame contains 7 or 8 data bits. However, your printer is an 8-bit printer; characters, controls, and all points addressable (APA) graphics need 8 bits of data.
Page 353 Start and Stop Bits The printer receives data with 1 start bit and either 1 or 2 stop bits. The printer always sends 1 start and 2 stop bits. Parity There are four possible parity settings: Odd, Even, None, and Ignore.
Page 354 XON/XOFF/DTR • XON/XOFF/DTR/DSR Your printer supports two modes in which both hardware and software data flow control protocols are performed. In XON/XOFF/DTR mode, the printer uses both XON/XOFF and DTR pacing. When XON/XOFF/DTR/DSR mode is active, the printer uses both XON/XOFF and DTR/DSR pacing.
Page 355 Table 8-5 shows the state of each serial interface signal in the three data flow control protocols when the Honor DSR setting is Off. Table 8-5: Serial Link (All Protocols) with Honor DSR Off Printer Signal DTR (Output) DSR (Input) CTS (Input) These values are compatible with Hewlett-Packard Company’s LaserJet printers.
Page 356 Only DTR/DSR is used for flow control from the printer to the host computer. DTR drops to tell the computer that the receive buffer is nearly full or that the printer is busy and that data transmission should stop. About 640 free bytes remain in the buffer at this time.
Page 357 Honor DSR.) After you power on the printer and DTR is active, the printer sends an XON signal to the computer (DC1 control or X'11'). However, the computer does not need to detect this initial XON before sending data to the printer, because the printer can be powered on before the computer or terminal.
Page 358 Serial Errors The printer places an underscore character in the link buffer when it detects an error. Some printers also display serial errors on the printer operator panel or through MarkVision Professional as attendance messages, such as a 54 Serial Option x Error do not generate such an error message are: •...
Page 359: Network Support
• Detect detachment of serial devices. Network Support Installing an internal print server enables you to connect your printer to a local area network (LAN). The print server supports these network interfaces: • The Token-Ring print server conforms to IEEE 802.5 using either IBM Cabling System (STP) or unshielded twisted-pair cable, which meets the IBM Cabling System Type 3 Media Specification (UTP).
Page 360: Input Buffer
100BaseTX networks using Category 5 UTP cabling. For information on installing a print server in your printer, see your printer documentation. You may also connect your printer to a LAN by using an external print server. Use one of the following: •...
Page 361 Note: MB represents 1,048,576 bytes. K represents 1024 bytes. N/A means non-applicable. Note: When using serial communication, the printer signals the host computer to stop transmitting bytes when the serial input buffer is within 640 bytes. In addition, when XON/XOFF protocol is used, the printer signals the host computer to stop transmitting when the serial input buffer is 384, 256, and 128 bytes from full.
Page 362 Table A-1 lists PCL emulation commands and identifies printers that support them. For detailed information about PCL emulation commands and how to select them, see “PCL Emulation” on page 2-1. Table A-2 on page A-6 identifies printer support for the GL/2 commands. Table A-1: PCL Emulation Commands Supported...
Page 363 & Job Separation & Long-Edge Offset Registration & Number of Copies & Short-Edge Offset Registration &n#W [operation] Alphanumeric ID [string id] &p#C Palette Control PCL Support Printer Model Page 2-73 2-73 2-74 2-74 2-78 2-82 2-82 2-78 2-75 2-81 2-76...
Page 364 Secondary Font Spacing )s#S Secondary Font Style )s#T Secondary Font Typeface Selection )s#V Secondary Font Height (Point Size) )s#W[data] Load Font Header *b#M Set Raster Compression Mode PCL Support Printer Model Page 2-89 2-89 2-80 2-91 2-92 2-81 2-72 2-79 2-80...
Page 365 #W[data] Color Lookup Tables *m#W[data] Download Dither Matrix *o#M(b) Print Quality *o#W[data] Driver Configuration Command *p#P Push / Pop Palette *p#R Set Pattern Reference Point PCL Support Printer Model Page 2-86 2-87 2-86 2-84 2-84 2-82 2-82 2-82 2-83, 2-85...
Page 366 Color Component Three *v#I Assign Color Index *v#N Source Transparency Mode *v#O Pattern Transparency Mode *v#S Foreground Color *v#T Select Current Pattern *v#W[data] Configure Image Data PCL Support Printer Model Page 2-77 2-78 2-86 2-86 2-86 2-86 2-89 2-87 2-87 2-91 2-91...
Page 367 Function Arc Absolute Anchor Corner Define Alternate Font Arc Relative Arc Absolute Three Point Bezier Relative Bezier Absolute Character Fill Circle Comment Character Plot PCL Support Printer Model Page 2-90 2-74 2-78 2-92 2-92 2-72 Printer Model Page 2-94 2-96...
Page 368: Pcl Support
Input P1 and P2 Input Relative P1 and P2 Input Window Line Attributes Label, Default Terminator = ‘03’x Label Origin Uses PCL Label Origin Line Type Label Mode Logical Operation PCL Support Printer Model Page 2-96 2-93 2-95 2-95 2-95 2-95 2-94 2-94...
Page 369 Absolute Character Size Character Slant Symbol Mode Select Pen Relative Character Size Select Standard Font Screened Vectors Screened Vectors - 9, level Transparent Data Threshold Matrix PCL Support Printer Model Page 2-96 2-94 2-96 2-94 2-94 2-94 2-94 2-94 2-94...
Page 370 Table A-2: GL/2 Commands (Continued) Supported Page numbers reference command descriptions. Not Supported Command Function Transparency Mode User Defined Line Fill Wedge Pen Width Units PCL Support Printer Model Page 2-96 2-96 2-95 2-96...
Page 371: Pjl Support
For detailed information about PJL commands, see “Printer Job Language” on page 3-1. All commands may not have a full description. Note: The word common applies to those variables common to both your Lexmark printer and the Hewlett-Packard Company’s LaserJet printers. Table B-1: Common Variables for Both Printer Languages...
Page 372 Table B-1: Common Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name FORMLINES HOLD HOLDKEY HOLDTYPE IMAGEADAPT INTRAY1 INTRAY2...
Page 373 Table B-1: Common Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name ORIENTATION OUTBIN PAGEPROTECT PAPER PARALLEL PASSWORD PERSONALITY...
Page 374 Table B-2: Printer Unique PJL Variables for Both Printer Languages Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LACTIVEBINRESET LADVANCEDSTATUS LALARMCONTROL LAUTOCRLF LAUTOLFCR LBLANKPAGES...
Page 375 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LCUSTOMPAPERUNITS LCUSTOMPAPERWIDTH LCUSTOMPAPERHEIGHT LCUSTOMPAPERFEED LCUSTOMTYPE1LENGTH...
Page 376 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LCUSTOMTYPE4NAME LCUSTOMTYPE4OUTBIN LCUSTOMTYPE4TEXTURE LCUSTOMTYPE4WEIGHT LCUSTOMTYPE5LENGTH...
Page 377 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LFAXREDIAL LFAXREDIALFREQUENCY LFAXTRANSMISSIONLOG LFEEDERPAPERTYPE LGLOSSYLOADING...
Page 378 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LLETTERHEADLENGTH LLETTERHEADLOADING LLETTERHEADOUTBIN LLETTERHEADTEXTURE LLETTERHEADWEIGHT...
Page 379 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LOPTIONALOUTBIN7NAME LOPTIONALOUTBIN8NAME LOPTIONALOUTBIN9NAME LOPTIONALOUTBIN10NAME LOUTBINCONFIG...
Page 380 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LPRINTQUALITY LPUNCH LREAROUTBINNAME LREPEATPRINTLIMIT LRESET...
Page 381 Table B-2: Printer Unique PJL Variables for Both Printer Languages (Continued) Supported Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Default values are listed for exceptions only. Variable Name LTRAY3SENSEDTYPETRANSPARENCY LTRAY4SENSEDTYPEPAPER LTRAY4SENSEDTYPETRANSPARENCY LTRAY1AUTOSIZE LTRAY2AUTOSIZE...
Page 382 Table B-3: Common Variables for PCL Emulation Supported Not Supported Page numbers reference variable descriptions. Variable Name FONTNUMBER FONTSOURCE PITCH PTSIZE SYMSET Table B-4: Printer Unique Variables for PCL Emulation Supported Not Supported Page numbers reference variable descriptions. Variable Name LA4WIDTH LASSIGNFEEDER LASSIGNMANUALENVELOPE LASSIGNMANUALPAPER LASSIGNMPFEEDER...
Page 383 Not Supported Page numbers reference variable descriptions and are listed for supported variables only. Variable Name JAMRECOVERY PRTPSERRS ADOBEMBT Table B-6: Printer Unique Variables for PostScript Emulation Supported Not Supported Page numbers reference variable descriptions. Variable Name LPICTUREGRADE LPSFONTPRIORITY B-13...
Page 384 Table B-7: Printer Unique LRESOURCE Variables Supported Not Supported Page numbers reference variable descriptions. Variable Name LDESCRIPTION LRWLOCK LWLOCK Table B-8: Status Readback Commands Supported Not Supported Page numbers reference command descriptions. Command Name Dinquire Echo Info Inquire Ustatus Ustatusoff...
Page 385 Insufficient Defragment Memory Intervention Required - 3-63 Insufficient Memory Intervention Required - 3-63 Memory Full Intervention Required - 3-63 Held Jobs May Not Be Restored B-15 Printer Model Page W840 3-60 3-60 3-60 3-60 Status Code Return String 30014 50 PPDS Font Error...
Page 386 56 Parallel Port Disabled 30018 56 Parallel Port x Disabled 30018 56 Standard USB Port Disabled 30019 35 Res Save Off Deficient Memory 30026 55 Insufficient Fax Buffer 30027 54 Std Par ENA Connection Lost PJL Support Printer Model W840...
Page 387 53 Unformatted Flash 30036 61 Defective Disk 30036 63 Unformatted Disk 30075 80 Scheduled Maintenance 30076 35 Res Save Off Deficient Memory 30076 37 Insufficient Collation Area 30107 Empty Hole Punch Box 30107 Empty Box M PJL Support Printer Model W840...
Page 388 54 Par x ENA Connection Lost 30113 56 Parallel Port x Disabled 32001 Operation Failed Jobs on Disk 32001 Operation Failed Faxes on Disk 32002 52 Flash Full 32002 62 Disk Full 32015 Disk Corrupted. Reformat? PJL Support Printer Model W840...
Page 389 40038 80 Fuser Maintenance 40038 80 Fuser Life Warning 40038 80 Belt Life Warning 40038 80 Fuser/Belt Life Warning 40038 80 Fuser Exhausted 40038 80 Belt Exhausted 40038 80 Fuser/Belt Exhausted 40038 83 ITU Maintenance PJL Support Printer Model W840...
Page 390 Intervention Required - 3-67 Cartridge Life Expired Intervention Required - 3-68 Cartridge Life Warning Intervention Required - 3-67 Printer Upper Door Open Intervention Required - 3-68 Printer Cover Open Intervention Required - 3-67 Close Toner Box Cover Intervention Required -...
Page 391 Change Cartridge Invalid Refill 40021 Open Cover 40021 Open Rear Door 40021 Close Front Door 40021 Close Side Door 40021 Close Finisher Door 40021 Close Finisher Side Door 40021 Close Finisher Top Cover 40021 Close Door <d> PJL Support Printer Model W840...
Page 392 40029 Reattach Output Bin <bin #> 40029 Reattach Bins <bin #x - bin #y> 40029 Install Bin x or Cancel Job 40029 Check Finisher Installation 40029 Check Mailbox Installation 40030 33 Tray x Config Error PJL Support Printer Model W840...
Page 393 88 Color Print Cartridge Low 88 Black Print Cartridge Low 88 Photo Print Cartridge Low 88 Yellow Toner Empty 88 Magenta Toner Empty 88 Cyan Toner Empty 88 Black Toner Empty 40038 84 Black Photo Dev Life Warning PJL Support Printer Model W840...
Page 394 40038 Replace Toner Cartridge 40038 Replace Toner To Continue 40038 Replace Oil Coating Roll 40039 89 Cartridge Empty <CMYK> 40040 Load Staples 40041 Priming Failed. Retry? 40048 OPMSG message 40049 STMSG message 40050 Replace Fuser PJL Support Printer Model W840...
Page 395 40088 59 Incompatible Duplex 40089 59 Incompatible Tray x 40090 59 Incompatible Envelope Feeder 40095 Check Duplex Connection 40095 Install Duplex or Cancel Job 40096 Close Duplex Door 40096 Insert Duplex Option 40101 Load Staples PJL Support Printer Model W840...
Page 396 For more information, see “Table 3-16: Tray Values” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Values” on page 3-74. * See your printer documentation for return string messages. B-26 Status Code...
Page 397 For more information, see “Table 3-16: Tray Values” on page 3-74. yy represents a media size code. For more information, see “Table 3-17: Media Size Values” on page 3-74. * See your printer documentation for return string messages. B-27 Status Code...
Page 398 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 399 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 400 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 401 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 402 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 403 The door or cover needs to be opened. x represents the number of jammed pages in the printer. y represents the tray number. z represents the bin number.
Page 404 Table B-15: Device Attendance Messages Supported Not Supported Page numbers reference message descriptions. Message RDYMSG OPMSG STMSG Table B-16: Lexmark Unique PJL Commands Supported Not Supported Page numbers reference command descriptions. Command LBEEP LDOWNLOADTARGET LPORTROTATE LPRINT testpage • LPRINTDIRECTORY • LPRINTTESTPAGE •...
Page 405 Table B-16: Lexmark Unique PJL Commands (Continued) Supported Not Supported Page numbers reference command descriptions. Command LOPENFILE LCLOSEFILE LREADFILE LWRITEFILE LRUNFILE LRENAMEFILE LDELETEFILE LFORMAT LDEFRAG Table B-17: File and Device Protection Commands Supported Not Supported Page numbers reference command descriptions.
Page 406: Postscript Support
Operator Name appletalktype buildtime byteorder checkpassword currentfilenameextend currentmanualduplexmode currentuniversalsize defaulttimeouts deletefile devcontrol devdismount devforall devformat devmount devstatus diskonline diskstatus displayoperatormsg Printer Model Page W840 4-13 4-13 4-13 4-14 4-14 4-14 4-15 4-15 4-16 4-17 4-18 4-18 4-19 4-19 4-20 4-21...
Page 407 Printer Model Page W840 4-21 4-22 4-22 4-22 4-23 4-23 4-23 4-24 4-24 4-25 4-25 4-25 4-26 4-26 4-26 4-26 4-27...
Page 408 Printer Model Page W840 4-31 4-31 4-32 4-32 4-33 4-33 4-34 4-34 4-34 4-35 4-36 4-37 4-37 4-37 4-38 4-38 4-38...
Page 409 Page numbers reference operator descriptions. Operator Name setignoresize setjobtimeout setmanualduplexmode setpapertray setprintername setquiet setresolution setsccbatch setsccinteractive setsoftwareiomode settumble setuniversalsize setuserdiskpercent softwareiomode tumble userdiskpercent waittimeout Printer Model Page W840 4-43 4-43 4-44 4-44 4-45 4-45 4-46 4-46 4-46 4-47 4-47 4-47 4-48 4-48 PostScript Support...
Page 410 • PictureGrade • ImageEnhancement • PrintDarkness • AutoMediaType • EdgeToEdge • DefaultPoliciesPageSize • SubstituteSize • Type • ColorCorrection • ImageBrightness • ImageContrast • PrintQuality Duplex Printer Model Page W840 4-49 4-49 4-49 4-49 4-49 4-49 4-49 4-49 4-49 4-49 4-49...
Page 411 • 6 - Tray 5 – PageSize – MatchAll – MediaColor – MediaType – MediaWeight – InputLocation • Mode • Priority Install ManualFeed ManualFeedTimeout MediaColor MediaPosition Printer Model Page W840 4-52 4-52 4-52 4-53 4-53 4-53 4-53 4-53 4-53 4-53 4-53...
Page 412 • 6 - Optional Bin 6 • 7 - Optional Bin 7 • 8 - Optional Bin 8 • 9 - Optional Bin 9 • 10 - Optional Bin 10 – OutputType – OutputLocation Printer Model Page W840 4-55 4-55 4-55 4-55...
Page 413 PostRenderingEnhanceDetails • REValue • Type PowerSave ProcessColorModel Punch SlipSheet SlipSheetDetails • SlipSheetSource • Type Staple TraySwitch Tumble UniversalDetails • Type • PageSize Printer Model Page W840 4-58 4-58 4-58 4-59 4-59 4-59 4-59 4-59 4-59 4-60 4-60 4-60 4-60 4-60...
Page 414 JobName 4-64 JobTimeout 4-64 MaxDictStack 4-64 MaxExecStack 4-64 MaxFontItem 4-64 MaxFormItem 4-64 MaxLocalVM 4-64 MaxOpStack 4-65 Printer Model Page 4-62 4-62 Printer Model Default false Collation - Collated Copies (QTY) value true JobTimeout system parameter 10015 12500 100000 2147483647 100000...
Page 415 4-65 Table C-4: System Interpreter Parameters Supported Not Supported Page numbers reference parameter descriptions. Default values are listed. BuildTime ByteOrder CurDisplayList CurFontCache C-10 Printer Model Default 20000 48000 1024 5000 2147483647 false 25000 per MB of RAM WaitTimeout system parameter...
Page 416 DisableFastProcs DoPrintErrors DoStartPage EnableExtraFonts EngineBoot EngineCode EngineSpeed EnvironmentSave FactoryDefaults FatalErrorAddress FontResourceDir FontVersion GenericResourceDir GenericResourcePathSep InstalledRam JobTimeout languagelevel MaxDisplayList C-11 Printer Model Page W840 4-66 4-67 4-67 4-67 4-67 4-67 4-67 4-67 4-67 4-68 4-68 4-68 4-68 4-68 4-68 4-68 4-68...
Page 417 MaxScreenStorage MaxSourceList MaxUPathCache PageCount PanelCode PrinterCode PrinterName RamSize RealFormat Revision SearchBuiltinFontsFirst SerialNumber StartJobPassword StartupMode StaticRamSize SystemParamsPassword UseOldcopypage UseOldfonts C-12 Printer Model Page W840 4-69 4-69 4-69 4-69 4-69 4-69 4-69 4-69 4-70 4-70 4-70 4-70 4-70 4-70 4-70 4-70 4-70...
Page 418 Table C-4: System Interpreter Parameters (Continued) Supported Not Supported Page numbers reference parameter descriptions. Default values are listed. ValidNV WaitTimeout C-13 Printer Model Page W840 4-71 4-65 PostScript Support...
Page 419 Table C-5: Devices Supported Supported Not Supported n Network version of the printer model Device Page %ParallelA% 4-66 %ParallelB% %ParallelC% %ParallelD% %SerialA% %SerialB% %SerialC% %SerialD% %LocalTalkA% %LocalTalkB% %LocalTalkC% %LocalTalkD% %EtherTalkA% %EtherTalkB% %EtherTalkC% %EtherTalkD% %IR_A% %IR_B% %IR_C% %IR_D% %USB_A% %USB_B% %USB_C%...
Page 420 Table C-5: Devices Supported (Continued) Supported Not Supported n Network version of the printer model Device Page %AppSocketC% 4-66 %AppSocketD% %RemotePrinterA% %RemotePrinterB% %RemotePrinterC% %RemotePrinterD% %PrintServerA% %PrintServerB% %PrintServerC% %PrintServerD% %LPR_A% %LPR_B% %LPR_C% %LPR_D% %LexLinkA% %LexLinkB% %LexLinkC% %LexLinkD% %IP_A% %IP_B% %IP_C% %IP_D%...
Page 421 PSSmartSwitch Type Device Parameters for the Communication Device %Serial%, %SerialA%, %SerialB%, %SerialC%, %SerialD% Baud CheckParity DataBits DelayedOutputClose Enabled Filtering FlowControl HasNames HonorDSR Interpreter C-16 Printer Model Page 4-73 4-73 4-73 4-73 4-73 4-73 4-73 4-73 4-73 4-73 4-74 4-74 4-74...
Page 422 Filtering HasNames Interpreter LocalTalkType NodeID PCLSmartSwitch PortLocation PSSmartSwitch Type Device Parameters for the Communication Device %EtherTalk%, %EtherTalkA%, %EtherTalkB%, %EtherTalkC%, %EtherTalkD% DelayedOutputClose Enabled C-17 Printer Model Page 4-75 4-75 4-75 4-75 4-75 4-75 4-75 4-76 4-76 4-76 4-76 4-76 4-76 4-76...
Page 423 %IR_A%, %IR_B%, %IR_C%, %IR_D% DelayedOutputClose Enabled Filtering HasNames Interpreter PCLSmartSwitch PortLocation PSSmartSwitch Type Device Parameters for the Communication Device %USB%, %USB_A%, %USB_B%, %USB_C%, %USB_D% DelayedOutputClose Enabled C-18 Printer Model Page 4-77 4-77 4-77 4-78 4-78 4-78 4-78 4-78 4-78 4-78 4-78 4-78 4-78...
Page 424 Device Parameters for the Communication Device %TokenTalk%, %TokenTalkA%, %TokenTalkB%, %TokenTalkC%, %TokenTalkD% Address Bridging DelayedOutputClose Enabled Filtering HasNames Interpreter NodeID PCLSmartSwitch PortLocation PSSmartSwitch TokenTalkType Type Zone C-19 Printer Model Page 4-80 4-80 4-80 4-80 4-80 4-80 4-80 4-80 4-80 4-80 4-81 4-81 4-81 4-81 4-81 4-81...
Page 425 DelayedOutputClose Enabled Filtering HasNames Interpreter PortLocation Type Device Parameters for the Communication Device %PrintServer%, PrintServerA%, PrintServerB%, %PrintServerC%, %PrintServerD% DelayedOutputClose Enabled Filtering HasNames C-20 Printer Model Page 4-82 4-82 4-82 4-82 4-82 4-82 4-82 4-82 4-83 4-83 4-83 4-83 4-83 4-83...
Page 426 Filtering HasNames Interpreter PortLocation Type Device Parameters for the Communication Device %LexLink%, %LexLinkA%, %LexLinkB%, %LexLinkC%, %LexLinkD% DelayedOutputClose Enabled HasNames Interpreter PortLocation Type C-21 Printer Model Page 4-84 4-84 4-84 4-84 4-85 4-85 4-85 4-85 4-85 4-85 4-85 4-85 4-85 4-86...
Page 427 Type Device Parameters for the Communication Device %TokenRingPhysical%, %TokenRingPhysicalA%, %TokenRingPhysicalB%, %TokenRingPhysicalC%, %TokenRingPhysicalD% Address PortLocation Speed Type Device Parameters for the Parameters Device %Engine% BSizeStandard Darkness C-22 Printer Model Page 4-86 4-86 4-86 4-86 4-86 4-86 4-86 4-86 4-87 4-87 4-87...
Page 428 Device Parameters for the Parameters Device %Calendar%, %CalendarA%, %CalendarB%, %CalendarC%, %CalendarD% Hour Minute Month Running Second Type Year DateTime DayOfWeekLong DayOfWeekNum DayOfWeekShort C-23 Printer Model Page 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89 4-89...
Page 429 Type Writeable Device Parameters for the Parameters Device %flash1% BlockSize Free HasNames InitializeAction LogicalSize Mounted PhysicalSize Removable Searchable SearchOrder Type Writeable C-24 Printer Model Page 4-89 4-89 4-89 4-90 4-90 4-90 4-90 4-90 4-90 4-90 4-90 4-90 4-90 4-90 4-91...
Page 430 Removable Searchable SearchOrder Type Writeable Table C-7: PostScript Commands: Message Keys Supported Not Supported Page numbers reference status message key and value descriptions. status source C-25 Printer Model Page 4-92 4-92 4-92 4-92 4-92 4-92 4-92 4-92 4-92 4-92 4-92...
Page 431: Index
DTR/DSR protocol 8-23, 8-24 edge to edge printing See whole page setting electrical specifications 7-2 envelope sizes supported 4-9 Lexmark C510(n) 2-4, 2-6, 2-8 environmental commands and variables (PJL) 3-7 environmental conditions 7-4 errors, service 3-80 escape commands (PCL emulation)
Page 432 6-2 viewing the contents 6-3 fonts PCL emulation Lexmark X422 2-12 printing directory list for flash or disk 3-83, 6-3 saving on flash memory or disk 6-3 setting password protection 3-93 formatting flash or disk, PJL 3-92...
Page 433 PCL emulation 2-3 paper handling 3-72 paper sizes status message codes 3-74 paper sizes supported Lexmark C510(n) 2-4, 2-6, 2-8 paper trays PCL emulation paper size 2-73 paper source 2-73 PostScript emulation automatic size sensing search order 4-4...
Page 434 2-74 long-edge offset registration 2-72 number of collated copies 2-71 number of copies 2-71 output bin 2-75 printer reset 2-71 short-edge offset registration 2-72 simplex/duplex print 2-71 unit of measure 2-72 Universal Exit Language 2-72 macros...
Page 435 Lexmark X422 2-12 GL/2 Language 2-93 linking commands 2-69 paper and envelope dimensions Lexmark C510(n) 2-4, 2-6, 2-8 password protection 3-93 saving files on flash memory or disk 6-3 selecting MarkVision Professional 2-1 operator panel 2-1...
Page 436 accessing files 6-9 device names 6-9 device parameters 4-72 device search order 6-12 envelope size support 4-9 filenames 6-9 interpreter parameters 4-63 page device parameters 4-49 paper size commands currentuniversalsize 4-3 ignoresize 4-3 setignoresize 4-3 setuniversalsize 4-4 paper tray commands manualfeed 4-7 papertray 4-7 setpapertray 4-8...
Page 437 4-66 user parameters 4-63 using the operator panel 4-1 power requirements 7-2 printable areas 2-3, 2-10 Printer Job Language (PJL) attendance messages 3-67 30 Print Unit Missing 3-67 30 Coating Roll Missing 3-67 31 Defective Cartridge XXXX 3-67...
Page 438 Load Staples 3-71, 3-72 Open Cover 3-68 Open Rear Door 3-68 OPMSG message 3-71 paper handling 34 Incorrect Media 3-73 34 Wrong Paper Size in Tray x 3-73 34 Wrong Paper Size Manual Feed 3- Change <source> 3-73 Check <source> Paper Guide 3-73 Insert Duplex Pages &...
Page 439 37 Insufficient Collation Area 3-63, 3-65 37 Insufficient Defrag Memory 3-63 37 Insufficient Memory 3-63 38 Memory Full 3-63 39 Complex Page 3-63 50 PPDS Font Error 3-63 51 Defective Flash 3-64, 3-66 52 Flash Full 3-64, 3-66 53 Unformatted Flash 3-64, 3-66 54 Network x Software Error 3-65 54 Par x ENA Connection Lost 3-65 54 Parallel Error 3-63...
Page 440 Replace Fuser 3-61, 3-62 Replace PC Kit 3-61, 3-62 Replace Toner 3-61, 3-62 Replace Transfer 3-62 Res Reduced 3-62 Resetting the Printer 3-61 Tray <source #> Empty 3-62 Tray <source #> Missing 3-62 Waiting 3-62 status messages and codes 3-61...
Page 441 LBLANKPAGES 3-19 LBONDLENGTH 3-19 LBONDLOADING 3-19 LBONDOUTBIN 3-20 LBONDTEXTURE 3-20 LBONDWEIGHT 3-20 LBWLOCK 3-20 LCANCEL 3-20 LCARDSTOCKLENGTH 3-20 LCARDSTOCKLOADING 3-20 LCARDSTOCKOUTBIN 3-21 LCARDSTOCKTEXTURE 3-21 LCARDSTOCKWEIGHT 3-21 LCOLLATION 3-21 LCOLORCORRECTION 3-21 LCOLOREDLENGTH 3-21 LCOLOREDLOADING 3-22 LCOLOREDOUTBIN 3-22 LCOLOREDTEXTURE 3-22 LCOLOREDWEIGHT 3-22 LCOLOREXTENSIONS 3-50 LCOLORMODEL 3-22 LCUSTOMPAPERFEED 3-23...
Page 442 LIMAGESMOOTHING 3-33 LINFEEDERSIZE 3-33 LINKALERT 3-33 LINMPFEEDERSIZE 3-33 LJAMRECOVERY 3-33 LLABELSLENGTH 3-33 LLABELSLOADING 3-33 LLABELSOUTBIN 3-34 LLABELSTEXTURE 3-34 LLABELSWEIGHT 3-34 LLASTTRAYRENUMBER 3-34 LLEFTMARGINOFFSET 3-34 LLETTERHEADLENGTH 3-34 LLETTERHEADLOADING 3-34 LLETTERHEADOUTBIN 3-35 LLETTERHEADTEXTURE 3-35 LLETTERHEADWEIGHT 3-35 LMANUALENVELOPESIZE 3-36 LMANUALENVELOPETYPE 3-36 LMANUALPAPERSIZE 3-36 LMANUALPAPERTYPE 3-36 LMPFEEDERPAPERTYPE 3-36 LMULTIPAGEBORDER 3-36...
Page 443 8-11 XON/XOFF 8-26 raster compression mode 2-97 adaptive compression 2-101 delta row 2-100 group 3 and 4 2-102 Lexmark adaptive 2-103 run-length encoded data 2-99 Tagged Image File Format (TIFF) 2-99 uncoded data 2-98 raster image graphics 2-97 receivers...
Page 444 Symbol Set Tables, locating ID values 2-69 symbol sets printing directory list flash memory or disk 6-3 selecting Lexmark E323 2-51 Lexmark T630 2-51 Lexmark T632 2-51 Lexmark T634 2-51 setting password protection 3-93 storing on flash memory or disk 6-3...
Page 445 3-12 common for PCL emulation 3-48 common for PostScript emulation 3-51 environment 3-7 printer unique for all printer languages 3-19 printer unique for PCL emulation 3-49 weight, printer 7-3 whole page setting 2-11 XON/XOFF protocol 8-23...

This manual is also suitable for:

T640 W840 20g0130 - t 640dn b/w laser printer 20g0460 - t644tn - printer 20g0500 - t 640dtn b/w laser printer T430d ... Show all

Lexmark T430 Technical Reference

Introduction

PCL Emulation

Printer Job Language

Postscript Emulation

Switching Languages

Flash Memory and Disk

Printer Specifications

Printer Interfaces

PCL Support

PJL Support

Postscript Support

Index

Quick Links

Technical Reference

Related Manuals for Lexmark T430

Summary of Contents for Lexmark T430

This manual is also suitable for:

Table of Contents