Program Reporting - Honeywell L5200 Series Installation And Setup Manual

LYNX Touch Installation and Setup Guide
Programming the Control

Program Reporting

When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central Station
programming; the "Phone Type" must be set to any selection other than "None", the "Communicator Type" must be set to
GSM or IP, as applicable, and must match the compass value; "Phone number" field must be left blank and an "Account
number" must be programmed.
The following system options are programmed in this section:
Option
Primary or Secondary CS Info
Phone Type
Phone Number
Communicator Type
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Follow Me Phone 1 or Phone 2
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Report Selection
Options
PBX
Call Wait Cancel
Number of Reports
Alarm Report Delay
Swinger Shutdown
Abort Window
First Offset Report
Report Frequency
Downloader
Phone Answer
Modem Speed
Ans. Machine Defeat
Ring Counter
Callback Number
Flexible Callback
Number
Enroll information pertaining to the Primary and/or Secondary Central Station.
Select the Report Format that will be used to send reports to the Primary or Secondary
Central Station, as applicable.
Enter the Phone Number for the Primary or Secondary Central Station, as applicable.
Select the type of Communications Module that will be used to communicate with the Primary
or Secondary Central Station, as applicable.
Enter the account number for the Primary or Secondary Central Station, as applicable.
Select the primary method for sending Reports to the Primary or Secondary Central Station,
as applicable.
Selects delay between switching between reporting methods. Active if Dynamic Delay feature
has been set to Preferred Telco or Preferred Radio.
Enable All Reports to be sent to the Primary or Secondary Central Station, as applicable.
Enable Alarm Reporting to the Primary or Secondary Central Station, as applicable.
Enable Trouble Reporting to the Primary or Secondary Central Station, as applicable.
Enable Open/Close Reporting to the Primary or Secondary Central Station, as applicable.
Enable Test Reporting to the Primary or Secondary Central Station, as applicable.
Enroll information Primary and/or Secondary telephone numbers for "Follow Me"
Announcements and/or Reminders. (This feature is only available on the LYNX Touch
L5200/L5200CN)
Enter Number for Follow Me Phone 1 or Phone 2, as applicable.
Enter Primary and/or Secondary telephone numbers for "Follow Me" Announcements and/or
Reminders.
Enable All Reports to be sent to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Alarm Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Trouble Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Open/Close Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Test Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Reporting of Specific Events
Enter the digits required to access telephone service. (Not applicable to the L7000/L7000CN)
Enter the digits required to cancel call waiting, if applicable (Not applicable to the L7000/
L7000CN)
Limit the number of messages sent to the Central Station during an armed period.
Disable or select the time delay for alarm reporting (applies to L5200CN/L7000CN only)
Select the number of times reports are sent and sounder sounds for non-fire alarms before
the system ignores subsequent alarms (applies to L5200/L7000 and only)
Select the time delay for alarm reporting (applies to L5200/L7000 only)
Select the time for the first test report following power-up/programming or downloading
Select the test report frequency
Enable to allow control to answer incoming phone line. (Not applicable to the L7000/
L7000CN)
(Future Use)
Enable to defeat answering machine mode. (Active if Phone Answer feature is enabled.)
(Not applicable to the L7000/L7000CN)
Enter the number of rings before control picks up phone line. (Active if Ans. Machine Defeat is
not enabled.)
Enter the phone number the control will use to call back the downloading computer. (Active if
Phone Answer is enabled.)
Allows Download operator to temporarily change the callback number by the number of digits
selected. Active if Phone Answer is enabled
Enter the number of flexible callback numbers that will be used. Available if Flexible Callback
is enabled.
- 40 -
Function