Installing Wireless Zones; General Information; Zones; Range - Honeywell L5200 Series Installation And Setup Manual

Hide thumbs Also See for L5200 Series:
Table of Contents

Advertisement

General Information

Zones

The L5200 and L7000 controls respectively support up to 79 and 103 total wireless zones using 5800 Series
transmitters, and wireless buttons.

Range

The built-in RF receiver can detect signals from wireless transmitters within a nominal range of 200 feet.

Transmitters

5800 Series transmitters have built-in serial numbers that must be entered into the system using the
"Zones" programming section, or input to the control via the downloader. 5800 Series transmitters (except
the 5800RL) do not have DIP switches. Each transmitter's zone number is also programmed into the system
in the "Zones" programming section. Some transmitters, such as the 5816 can support more than one "zone"
(referred to as loops or inputs). On the 5816, for example, the wire connection terminal block is loop 1; the
reed contact is loop 2. Each loop must be assigned a different zone number.
For button transmitters (RF "keys") such as the 5804, you must assign a unique zone number to each
individual button used on the transmitter. Each button on the transmitter also has a pre-designated loop or
input number, which is automatically displayed.
The 5816 Transmitters do not have EOL supervision of their loop wiring, which must not exceed 3 feet.
UL
The 5800RL, 5804BD, 5804BDV, 5804E, 5814, 5819, 5819S(WHS & BRS) and 5828/5828V transmitters have not been
evaluated by UL.

House Identification

If you are using a 5804BD/5804BDV Wireless Keypad with the system, you must program a House ID Code
(01–31) as described in the "SYSTEM TYPE" programming section to establish proper communication, and
the keypad must be set to the same ID. House ID 00 disables all wireless keypads. An RF House ID is not
necessary for other 5800 Series transmitters; the entry should be left at "00" (default) in those cases.

Transmitter Supervision

With the exception of some transmitters/keypads that may be carried off-premises (5804BD, 5804BDV and
5804E), each transmitter is supervised by a check-in signal that is sent to the receiver at 70–90 minute
intervals. If at least one check-in is not received from each supervised transmitter within a 12-hour period,
the "missing" transmitter zone number(s) and "Supervision" will be displayed. The supervision for a
particular transmitter in the system that may also be carried off the premises may be turned off by entering
it as a Unsupervised RF (UR) type, as described in the "ZONES" programming section. 5800 Series
transmitters have built-in tamper protection and will annunciate as a fault condition if covers are removed.
In Canada the RF supervision period is 3-hours for Fire zones and 12 hours for all other zone types.

Transmitter Input Types

Each of the transmitters has one or more unique factory-assigned input (loop) ID codes. Each of the inputs
requires a programming zone
as one of the following types
Type
Supervised RF ("RF")
Unsupervised RF ("UR")
Unsupervised Button RF ("BR")

Transmitter Battery Life

• Batteries in the wireless transmitters may last from 4–7 years, depending on the environment, usage, and
the specific wireless device being used. Factors such as humidity, high or low temperatures, as well as
large swings in temperature may all reduce the actual battery life in a given installation. The wireless
system can identify a true low battery situation, thus allowing the dealer or user of the system time to
arrange a change of battery and maintain protection for that point within the system.
• Button-type transmitters should be periodically tested for battery life. The 5804BD, 5804BDV, and 5804E
button transmitters have replaceable batteries.
(e.g., a 5804's four inputs require four button zones)
(see transmitter's instructions for appropriate input type)
Sends periodic check-in signals, as well as fault, restore, and low battery signals. The
transmitter must remain within the receiver's range.
Sends all the signals that the "RF" type does, but the control does not supervise the check-in
signals. The transmitter may therefore be carried off-premises.
Sends only fault signals. They do not send low battery signals until they are activated. The
transmitter may be carried off-premises.
LYNX Touch Installation and Setup Guide

Installing Wireless Zones

Description
- 17 -
. Transmitters can be entered
:

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Lynx touch l7000 series

Table of Contents