Lithium Ion Battery - Shimano XTR Di2 Dealer's Manual

TO ENSURE SAFETY
„Lithium ion battery
• Do not place the battery into fresh water or sea water, and do not allow the battery terminals to get wet. If this is not observed, fire, bursting or
overheating may occur.
• Do not use the battery if it has any noticeable scratching or other external damage. If this is not observed, bursting, overheating or problems with
operation may occur.
• Do not subject the battery to strong shocks or throw it. If this is not observed, bursting, overheating or problems with operation may occur.
• Do not use the battery if leakages, discoloration, deformation or any other abnormalities occur. If this is not observed, bursting, overheating or
problems with operation may occur.
• If any leaked fluid gets on your skin or clothes, wash it off immediately with clean water. The leaked fluid may damage the skin.
• The operating temperature ranges for the battery are given below. Do not use the battery in temperatures outside these ranges. If the battery is used
or stored in temperatures which are outside these ranges, fire, injury or problems with operation may occur.
1. During discharge: –10 °C - 50 °C
2. During charging: 0 °C - 45 °C
SM-BTR1 : Lithium ion battery
• If charging is not complete after 1.5 hours of charging, stop charging. If this is not observed, fire, bursting or overheating may occur.
SM-BTR2 : Lithium ion battery
• If the battery does not become fully charged after 4 hours of charging, stop charging. If this is not observed, fire, bursting or overheating may occur.
„Battery charger / Battery charger cord
• Be sure to hold the power cable by the power plug when connecting and disconnecting the power plug from the electrical outlet. If you do not hold
the power cable by the power plug, fire or electric shocks may occur.
If the following symptoms are observed, stop using the device and contact a dealer. A fire or electric shock may be caused.
* If heat or acrid-smelling smoke is coming out from the power plug.
* There may be a bad connection inside the power plug.
• Do not overload the electrical outlet with appliances beyond its rated capacity, and use only a 100 – 240 V AC electrical outlet. If the electrical outlet is
overloaded by connecting too many appliances using adapters, overheating resulting in fire may occur.
• Do not damage the power cord or power plug. (Do not damage, process, forcibly bend, twist or pull them, bring them near hot objects, place heavy
objects on them or bundle them tightly together.) If they are used while damaged, fire, electric shocks or short-circuits may occur.
• Do not use the charger with commercially-available electrical transformers designed for overseas use, as they may damage the charger.
• Always be sure to insert the power plug as far as it will go. If this is not observed, fire may occur.
SM-BCR2: Battery charger for SM-BTR2
• Do not use any USB cable other than the USB cable which is supplied with the PC linkage device. This may cause a charge error, fire, or failure of the
connected PC due to heating.
• Do not connect the charger to PC when it is on standby. This may cause a failure of PC depending on its specifications.
• When connecting or disconnecting the USB cable or the charging cable, be sure to hold the plug of the cable. Failure to do so may cause a fire or
electric shock.
• If the following symptoms are observed, stop using the device and contact a dealer. A fire or electric shock may be caused.
* If heat or acrid-smelling smoke is coming out from the power plug.
* There may be a bad connection inside the power plug.
• If it thunders while charging with an AC adapter with a USB port, do not touch the device, bicycle, or the AC adapter. When lightning strikes, an
electric shock may be caused.
• Use an AC adapter with a USB port with a voltage of 5.0 VDC and with a current equal to or higher than 1.0 ADC. If the one with a current lower than
1.0 ADC is used, a charge error may occur or the AC adapter may heat up, leading to a fire.
• Do not use a USB hub when connecting the cable to a PC USB port. This may cause a charge error or fire due to heating.
• Be careful not to damage the charging cable. (Do not damage, process, forcibly bend, twist or pull them, bring them near hot objects, place heavy
objects on them or bundle them tightly together.) If they are used while damaged, fire, electric shocks or short-circuits may occur.
8