Table of Contents
Advertisement
Chapter 6
Upgrading and Maintaining the Cisco 6260 System
Figure 6-5
STATUS
STATUS
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATUC-1
ATUC-1
-4DMT
-4DMT
STATUS
STATUS
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATUC-1
ATUC-1
-4DMT
-4DMT
Step 5
Lift up on the ejector levers and gently apply pressure to the bottom of the faceplate while pushing the
card into the slot.
Push on the faceplate of the card to fully seat the card.
Step 6
Step 7
Press down on the ejector levers to secure the card and connect it to the backplane.
Step 8
Use a flat-head screwdriver to turn the locking tabs on the faceplate so that they overlap the NI-2 card
ejector levers to prevent inadvertent dislodging, as shown in
Figure 6-6
Locked
position
Step 9
Verify that the STATUS, ACTIVE, and POWER LEDs on the NI-2 card are solid green after the self-test
is complete. This self-test procedure takes several minutes. If the STATUS LEDs are not green after the
self-test, see
OL-2365-02
NI-2 Card Installation
NI
BLANK
NI-2
-155SM-1 55SM
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ACO
RESET
TRUNK 1
T
R
T
R
E
X
X
C
ATUC-1
S
ATUC-1
ATUC-1
S
S
L
-4DMT
T
ATUC-1
-4DMT
-4DMT
T
T
K
ATUC-1
-4DMT
ATUC-1
ATUC-1
A
A
-4DMT
-4DMT
-4DMT
T
T
ALARM S
CRITIC AL
MAJOR
MINOR
STATUS
POWER
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
FAN 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
FAN 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
C
ATU-C 4
N
S
L
A
SBTD 2
U
X
T
R
T
R
E
X
X
C
ATUC-1
S
S
S
L
ATUC-1
ATUC-1
-4DMT
T
T
T
ATUC-1
K
-4DMT
-4DMT
ATUC-1
A
A
-4DMT
E
ATUC-1
ATUC-1
-4DMT
T
N
-4DMT
-4DMT
T
E
T
Positioning the Locking Tab for NI-2 Card Removal and Installation
Unlocked
position
Chapter 5, "Troubleshooting,"
PEM 1/PEM 2
AUD_CRIT/A UD_MAJ
AUD_MIN/V IS_CRIT
60V
VIS_MAJ/VIS _MIN
0.5 A MAX
STAT_ALAR MS
BUS_A/BITS _B
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATUC-1
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
-4DMT
ATUC-1
-4DMT
-4DMT
ATUC-1
-4DMT
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
-4DMT
-4DMT
for troubleshooting procedures.
Installing and Replacing Hardware
Figure
6-6.
Cisco 6260 Hardware Installation Guide
6-11
Advertisement
Table of Contents
