Table of Contents
Advertisement
Installation Procedures
Step 3
Carefully lift the chassis from underneath and rest it on the mounting aids, as shown in
Figure 4-3
Push the chassis back into the rack.
Step 4
Using a Phillips-head screwdriver, screw the ear brackets on the chassis to the rack. Use two screws at the
Step 5
top of each ear bracket and two at the bottom (four screws per bracket). For stability, make sure you use at
least one round hole at each end of each bracket (the ear brackets have both round and oval holes).
Repeat
Step 6
4.2.4 Install Blank Faceplates
Blank faceplates should occupy any empty slots in the Cisco 6260 chassis. Blank faceplate installation
is similar to line card installation.
Cisco 6260 Hardware Installation Guide
4-6
Mounting Aids Support the Chassis During Installation
NI-2
-155SM-1 55SM
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ACTIVE
ATU-C 1
ACTIVE
ACTIVE
ACO
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 1
ATU-C 2
ATU-C 1
ATU-C 1
ATU-C 2
RESET
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 2
ATU-C 3
ATU-C 3
TRUNK 1
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
T
R
T
ATU-C 4
R
ATU-C 4
ATU-C 4
X
E
X
C
S
L
S
S
T
K
T
T
A
A
T
T
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
-4DMT
-4DMT
ALARM S
CRITIC AL
MAJOR
MINOR
POWER
READY
ACTIVE
FAN 1
FAN 2
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
C
ACTIVE
ACTIVE
ACTIVE
ACTIVE
N
ACTIVE
ACTIVE
ATU-C 1
ACTIVE
ATU-C 1
ATU-C 1
ACTIVE
S
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 1
L
ATU-C 2
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
A
ATU-C 3
ATU-C 2
ATU-C 3
ATU-C 2
ATU-C 2
SBTD 2
ATU-C 3
U
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 3
ATU-C 3
X
ATU-C 4
ATU-C 3
ATU-C 4
ATU-C 4
T
ATU-C 4
R
T
R
ATU-C 4
ATU-C 4
ATU-C 4
E
X
X
C
ATU-C 4
S
L
S
S
T
T
T
K
E
A
A
T
T
N
E
T
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
-4DMT
-4DMT
Step 1
through
Step 5
for each Cisco 6260 chassis that you are installing.
Chapter 4
Installing a Cisco 6260 Without a POTS Splitter Configuration
PEM 1/PEM 2
AUD_CRIT/ AUD_MAJ
AUD_MIN/V IS_CRIT
60V
VIS_MAJ/VI S_MIN
1 A MAX
STAT_ALAR MS
BUS_A/BITS _B
NI
BLANK
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
-4DMT
ATUC-1
-4DMT
-4DMT
STATUS
STATUS
STATUS
STATUS
STATUS
STATUS
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 1
ATU-C 2
ATU-C 1
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 2
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 3
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATU-C 4
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
ATUC-1
ATUC-1
-4DMT
ATUC-1
-4DMT
-4DMT
-4DMT
Figure
4-3.
OL-2365-02
Advertisement
Table of Contents
