Toro Reelmaster 5210 Service Manual page 77

CAUTION
Before opening hydraulic system, operate all hy-
draulic controls to relieve system pressure and
avoid injury from pressurized hydraulic oil. See
Relieving Hydraulic System Pressure in the Gen-
eral Information section of this chapter.
NOTE: The reel motors are connected in series. To iso-
late a faulty motor, all motors in the circuit may have to
be tested by starting with the upstream motor first.
5. For reel motor to be tested, thoroughly clean junction
of the motor case drain hose (small diameter hose)
where it connects to traction unit bulkhead (not at the
motor) (Fig. 42). Disconnect the case drain hose and put
a steel cap on the fitting at the traction unit. Leave the
case drain hose from the motor open and place open
end of disconnected hose into a drain pan.
IMPORTANT: Make sure that the oil flow indicator
arrow on the flow gauge is showing that the oil will
flow from the reel motor, through the tester and into
the return hose.
6. On reel motor to be tested, thoroughly clean junction
of hydraulic return hose (rear hose) and reel motor fit-
ting. Disconnect return hose from the motor. Install tes-
ter with pressure gauges and flow meter in series with
the motor and disconnected return hose. Make sure the
flow control valve on tester is fully open.
7. Set reel speed control to the full speed position.
Make sure Mow/Backlap lever is in the "Mow" position.
NOTE: Use a graduated container, special tool
TOR4077, to measure case drain leakage (Fig. 41).
8. Start engine and run at idle speed. Check for any hy-
draulic leakage from test connections and correct be-
fore proceeding with test.
CAUTION
Cutting unit reels will rotate when performing the
motor efficiency test. Keep away from cutting
units during test to prevent personal injury from
rotating reel blades. Do not stand in front of the
machine.
9. Sit on seat and move throttle to full speed (3200
RPM). Press PTO switch to ON. Move "Lower-Mow/
Raise" lever forward to engage cutting units.
Reelmaster 5010 Series
10.While watching pressure gauges, slowly close flow
control valve on tester until a pressure of 1200 PSI (83
bar) is obtained.
11. After achieving 1200 PSI (83 bar), place discon-
nected motor case drain hose into a container gra-
duated in ounces or milliliters (e.g. Toro #TOR4077) and
collect hydraulic fluid for 15 seconds. After 15 sec-
onds, remove hose end from container. Then move the
PTO switch to OFF, open the tester flow control valve
and stop the engine.
12.Identify amount of oil collected in the container. Re-
cord test results.
For Reelmaster 5210 and 5410 machines, if flow
was greater than 16.0 ounces (473 milliliters) (.5
GPM/1.9 LPM), repair or replace the tested reel
motor (see Cutting Reel Motor Service in the Service
and Repairs section of this chapter).
For Reelmaster 5510 and 5610 machines, if flow
was greater than 22.4 ounces (662 milliliters) (.7
GPM/2.6 LPM), repair or replace the tested reel
motor (see Cutting Reel Motor Service in the Service
and Repairs section of this chapter).
If flow is less than the listed specifications, the tested
motor does not have excessive leakage.
13.After testing is completed, make sure that engine is
stopped, then relieve hydraulic system pressure (See
Relieving Hydraulic System Pressure in the General In-
formation section of this chapter). Disconnect tester
from motor and return hose. Connect return hose to the
reel motor. Remove plug from machine fitting and con-
nect case drain hose to the fitting.
14.If necessary, perform motor efficiency test on other
reel motors.
1. Case drain hose
Page 4 - - 45
2
1
Figure 42
2. Bulkhead fitting
Hydraulic System (Rev. C)