Panasonic KX-TA624 Installation Manual page 436

Step Program Title
211 No Dial Disconnection
212 CO Line Duration Limit
213 Bell Off Detection
301 Call Barring – System Speed Dial
Boundary Class
309 Emergency Dial Number Set
310 Account Codes
311 Automatic Pause Insertion Codes
312 Call Barring – Extension Lock
400 CO Line Connected Assignment
402 Pulse Speed Selection
404 CO Line Group Assignment
414 Outside Line Mode
to ( Day / Night / Lunch )
416
417 Pause Time
421 CPC Detection for Outgoing Calls
423 CO Line Ringing Pattern Selection
424 Reverse (Polarity) Check
500 DISA Incoming Dialling Mode
Selection - Auto Attendant
501 DISA Built-in Auto Attendant
502 OGM Mode Selection
( KX-TA 62491 required )
503 FAX Connection
( KX-TA 62491 required )
504 DISA Delayed Answer Time
505 DISA Waiting Time after OGM
506 DISA Busy Mode
507 DISA Intercept Mode
Disconnect / Intercept
508 DISA Ring Time before Intercept
509 DISA Ring time After Intercept
510 DISA No Dial Mode
513 Cyclic Tone Detection
( OGM option KX-TA62491 required )
NEW
P
rogramming Steps
( with reference to the KX-T30810 / 61610 )
Feature Description
Call disconnects if 1
within 20 seconds of seizing a CO Line
Sets maximum CO call time (Enabled Prog 613)
Sets the wait time between bell signals from CO line
Assigns the call barring class for System Speed Dial
Numbers
Stored 'Emergency' telephone numbers override the
following : 'COS Level' / 'Account Code Modes' /
'Electronic Extension Lock'
Assigns Account Codes for 'Verify - All' mode
40 codes can be assigned as Pause Codes.
Pause [ duration prog. step 417 ] is inserted after the
code
COS level applied to Locked Extensions
Options : COS Levels 2 / 3 / 4 / 5 / Disabled
Defines connected CO's
Sets CO Line 'Pulse Speed'
Options : 10 / 20 pps
Trunk Group assignment of CO's
NORMAL : Follows programming steps 408 ~ 410
DIL : Assigns one ext. to receive I/C CO call
(must be used if Call FWD is required)
DISA1 : The caller will hear a Tone or OGM
DISA2 : The caller will hear two different OGM
UCD : Call will be rec'd via UCD function
Assigns the Host PBX pause time
Enables CPC detection during an outside call.
If CPC is detected, the system disconnects the line
( disconnection time Program Step 420 )
Incoming CO Line ringing pattern
Options : Single / Double / Triple Ring
Detects CO Line reversal
Without AA System accepts : Ext. / Access No.
With AA System accepts : Ext. / Access / AA No.
Assigns Auto Attendant numbers '0 ~ 9'
to extension jacks
Mode 1 ~ 6 DISA or UCD functions can be used
to receive IC calls
Assigns an extension to receive FAX calls
when CNG is detected
Assigns delay in DISA answering a call
Options : 0 / 3 / 6 / 12 secs
Selects time the system waits for DTMF
or CNG tone after OGM played
Options : 0 / 5 / 10 / 15 secs
Sets DISA response to a dialled busy extensions
Options : Call waiting / Disconnect / play OGM 2
Sets DISA response to unanswered calls
Options : Disconnect / Intercept
Sets DISA Intercept time for unanswered calls
Options : 10 / 20 / 30 / 40 / 60 / 120secs
Sets the ring time at the Intercept destination
Options : 10 / 20 / 30 / 40 / 60 / 120secs
Selects action taken by DISA if no response is received
after OGM ( e.g. DTMF or CNG )
Options : Intercept / Disconnect
Sets the number of times Cyclic Tone has to be detected
before the system regards the call as complete
Options : Disable ( does not detect ) / 2 / 3 / 4 times
st
Digit is not dialled
Default
Enable
( disconnect )
10 mins
3 secs
Class 1
Locations
01 : 999 02 : 112
03 ~ 05 : Not stored
01 ~ 24 : Not stored
i.e. 01 : 1234
01 ~ 40 : Not Stored
i.e. 01 : 1234567
Disabled
CO 1 ~ 6 : Connected
10 pps
CO 1 : Trunk Group 1
through to
CO 6 : Trunk Group 6
NORMAL
1.5 secs
Disable
Double
Disabled
Without AA
0 ~ 9 : Not stored
i.e. 0 : Jack 01
Mode 1
All Jacks : Disabled
3 secs
5 secs
Disconnect
Intercept
20 secs
20 secs
DISA1 : Intercept
DISA2 : Intercept
4 times
( 5 of 6 )