Panasonic KX-TA624 Installation Manual page 435

Step Program Title
002 System Password
008 Operator Assignment
009 Extension Number Assignment
010 LCD Time Display Selection
011 Speed Dial Number Set
012 Alternative Feature Number Plan
100 Hunt Group
101 Station Hunt Type
102 Voice Mail Port
103 Voice Mail Port
DTMF Integration
104 Hold Mode Selection
105 Conference Tone
108 Recall Mode of a Station Locked
Extension
109 CO Indicator Assignment
110 Recall Key Mode
111 Hold Music Selection
External Music / Tone
112 DSS Console Indication Mode
( for FWD / DND )
115 Extension Ringing Pattern Selection
116 Conference Pattern Selection
117 Call Pick-up Tone
118 Pulse Restriction
119 Redialling after Pulse / Tone
conversion
120 Bell Frequency
121 Automatic Line Access Number
122 Auto Rotation of Line Access
123 Break Ratio
124 SLT Ring Mode
125 Call Barring Check for * , #
126 DSS Off-Hook Mode
202 Call Forward Start Time
203 Pickup Dial Delay Time
( Hot Telephone )
206 Dial Start Time
207 Recall Timing Range
208 Interdigit Time
210 DTMF Time
( 4 of 6)
NEW
P
rogramming Steps
( with reference to the KX-T30810 / 61610 )
Feature Description
Replaces the PBX Programming Switch
( Installation Manual Page 4 –3 )
Assigns the System Operator Telephone
Allows the extension numbering scheme to be changed
12 / 24 hour clock display options
Used for Speed Dials and Call ID Feature
Replaces feature with a code 50 ~ 59
Enables Station Hunting for Extension Groups
Assigns Hunting Type for Extension Groups
Enables Jacks ( assigned as Voice Mail Ports )
to send DTMF signalling to Voice Mail
Enables signalling of Call Status information to
Voice Mail ports ( busy, answered, ringing, etc. )
Assigns Call Hold Mode for SLT extensions
( Example - HOLD 1 : Recall + on-hook )
Confirmation Tone sent at the Start and End
of a Conference Call
Allows locked extensions to send a Recall signal whilst
talking to an external call
Allows an extension, not programmed to ring
[408 – 410]
to receive the call by pressing the CO Line button
Mode1: Sends Recall signal time ( Prog. Step 418 )
Mode2: Recall signal is sent while the button is pressed
Assigns External Music or Tone (Beep)
Assigns if an extension set as FWD/DND
shows as a flashing button on the BLF/ DSS
Sets Single / Double / Triple Ring Pattern
Set the max. number of parties in a conference
Confirmation tone sent
when the Call Pickup feature is used
Enables / Disables pulses being sent to the CO Line
during a conversation
( when Call Block is set in program step 401 )
Allows Redial to use tone dialling on a pulse CO Line
if the call had used * and # to convert to Tone
Sets the Bell Frequency for an SLT device
If set at '0' Operator call becomes '9'
Auto rotation of CO lines seized
Sets the break ratio to CO lines
Length of SLT Ring Cycle
Assigns if * and # are checked by the COS program
Making Intercom call by pressing DSS key
Call FWD no answer timer
Options : 5 / 10 / 15 / 20 secs
Auto Dial time delay
Options : 1 / 2 / 3 / 4 secs
Time between seizing a CO Line and digits being sent
Range : 0 ~ 1500 milliseconds
Sets the Range for Extensions - SLT
Maximum time allowed between digits when dialling
out. Options : 5 / 10 / 15 secs
Assigns the minimum duration
Default
* # : System Prog
1234 : Password
Jack : 01
Jack 01 ( Ext. 201 )
24 ( Ext. 224 )
12 HOUR
Not stored
Not stored
All groups : Disabled
All groups : Terminate
Jacks 07 / 08 / 15 / 16 :
Disabled
Disabled
HOLD 1
Enable ( send )
Disabled ( not allowed )
Enable ( Allow )
Mode 1
External Music
Enable ( Flashing )
Single
5 party (C-2 E-5)
Enabled ( Tone )
Enable
Disable
25 Hz
Dial 9
Disabled (no rotate)
Mode 1 (66%)
Mode 2 (3 sec)
Enable ( Check )
Enable
15 secs
3 secs
0 mS
Mode 1 (50 ~ 180 mS)
20 secs
(Prior to disconnection )
Mode 1 (80 mS)