Program Reporter - Honeywell LYNX Touch Series Installation And Setup Manual

When Compass service is required and GSM or IP are the only reporting channels: As part of Primary Central
Station programming; the "Phone Type" must be set to any selection other than "None", the "Communicator Type"

must be set to GSM or IP, as applicable, and must match the compass value; "Phone number" field must be left
blank and an "Account number" must be programmed.
The following system options are programmed in this section:
Option
Primary or Secondary CS Info
Phone Type
Phone Number
Communicator Type
Account Number
Dynamic Priority
Dynamic Delay
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Follow Me Phone 1 or Phone 2 Enroll information Primary and/or Secondary telephone numbers for "Follow Me"
Phone Type
Phone Number
Report All
Report Alarms
Report Troubles
Report Open/Close
Report Tests
Report Selection
Options
PBX
Call Wait Cancel
Number of Reports
Alarm Report Delay
Swinger Shutdown
Abort Window
First Offset Report
Report Frequency
Downloader
Phone Answer
Modem Speed
Ans. Machine Defeat
Ring Counter
Callback Number
Flexible Callback
Number
Enroll information pertaining to the Primary and/or Secondary Central Station.
Select the Report Format that will be used to send reports to the Primary or Secondary
Central Station, as applicable.
Enter the Phone Number for the Primary or Secondary Central Station, as applicable.
Select the type of Communications Module that will be used to communicate with the
Primary or Secondary Central Station, as applicable.
Enter the account number for the Primary or Secondary Central Station, as applicable.
Select the primary method for sending Reports to the Primary or Secondary Central
Station, as applicable.
Selects delay between switching between reporting methods. Active if Dynamic Delay
feature has been set to Preferred Telco or Preferred Radio.
Enable All Reports to be sent to the Primary or Secondary Central Station, as applicable.
Enable Alarm Reporting to the Primary or Secondary Central Station, as applicable.
Enable Trouble Reporting to the Primary or Secondary Central Station, as applicable.
Enable Open/Close Reporting to the Primary or Secondary Central Station, as applicable.
Enable Test Reporting to the Primary or Secondary Central Station, as applicable.
Announcements and/or Reminders.
Enter Number for Follow Me Phone 1 or Phone 2, as applicable.
Enter Primary and/or Secondary telephone numbers for "Follow Me" Announcements
and/or Reminders.
Enable All Reports to be sent to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Alarm Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Trouble Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Open/Close Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Test Reporting to the Follow Me Phone 1 or Phone 2, as applicable.
Enable Reporting of Specific Events
Enter the digits required to access an outside line, if applicable
Enter the digits required to cancel call waiting, if applicable
Limit the number of messages sent to the Central Station during an armed period.
(applies to LYNX Touch only)
Disable or select the time delay for alarm reporting (applies to LYNX Touch only)
Select the number of times reports are sent and sounder sounds for non-fire alarms
before the system ignores subsequent alarms (applies to LYNX Touch SIA only)
Select the time delay for alarm reporting (applies to LYNX Touch SIA only)
Select the time for the first test report following power-up/programming or downloading
Select the test report frequency
Enable or disable to allow control to answer incoming phone line.
(Future Use)
Enable to defeat answering machine mode. (Active if Phone Answer is enabled.)
Enter the number of rings before control picks up phone line. (Active if Ans. Machine
Defeat is not enabled.)
Enter the phone number the control will use to call back the downloading computer.
(Active if Phone Answer is enabled.)
Allows Download operator to temporarily change the callback number by the number of
digits selected. Active if Phone Answer is enabled
Enter the number of flexible callback numbers that will be used. Active if Flexible
Callback is enabled.
- 33 -
LYNX Touch Installation and Setup Guide
Programming the Control
Function
Reporter