Event Log; Contact Id & Sia Event Log Codes - Honeywell LYNX Touch Series Installation And Setup Manual

LYNX Touch Installation and Setup Guide
System Operation

Event Log

The LYNX Touch Series event log is capable of recording and displaying up to 128 system events. The type
of events that can be recorded is selectable and is programmed in the System Type programming field. The
event log can be reviewed by entering the Installer Programming or Master User Programming mode. Refer
to the LYNX Touch Series User Manual for additional information.
Note: In the unlikely condition that the backup battery becomes fully discharged when AC power is lost, any system activity performed after
the low battery notification will not be saved in the event log. Additionally, the panel will revert to the status condition as before the low
battery notification.
CID
Code
110 Alarm, Fire
121 Alarm, Duress
122 Alarm, Silent
123 Alarm, Audible
131 Alarm, Perimeter
132 Alarm, Interior
134 Alarm, Entry/Exit
135 Alarm, Day/Night
137 Alarm, Tamper
145 Expansion Module Tamper
146 Silent Burglary
150 24-Hour Non-Burglary
162 Carbon Monoxide Detected
301 Trouble, AC Loss
302 Trouble, Low System Battery
305 Trouble, System Reset
316 System Tamper*
341 Trouble, Case Tamper
344 Trouble, RF Receiver Jam Detect
351 Trouble, Telco 1 Fault
353 Trouble, Long Range Radio Transmitter Fault
373 Trouble, Fire Trouble
374 Trouble, Exit Error Alarm
380 Trouble, Sensor
381 Trouble, Loss of Supervision RF
383 Trouble, Sensor Tamper
384 RF Low Battery
401 Open/Close by User
403 Open/Close Automatic
406 Cancel
407 Remote Arm/Disarm
408 Quick Arm
441 Armed Stay
455 Auto-Arm Failed
459 Recent Close
570 Zone/Sensor Bypass
601 Manual Trigger Test Report
602 Periodic Test Report
606 Listen-in to follow
607 Walk Test
623 Event 90% Full
627 Program Mode Entry (Logged in Event Log Only)
628 Program Mode Exit (Logged in Event Log Only)
654 System Inactivity
655 Reset Master Code (Logged in Event Log Only)
759 Resident Monitor Zone Response
760 Resident Response Zone Response
761 General Monitor Zone Response
762 General Response Zone Response
Contact ID ® & SIA Event Log Codes
Definition
SIA
Code
AT/AR AC Trouble/AC Restoral
BA/BR Burglary Alarm/Burglary Restoral
CA/CD Automatic Closing/Closing Delinquent
CI Fail to Close (Log only)
CL Closing Report
CQ Remote Closing
CR Recent Closing
DF/DR Door Forced/Door Restoral
EA Exit Alarm
ES/EJ Expansion Device Tamper/Expansion Tamper Restore
ET Expansion Trouble
FA Fire Alarm
FT/FJ Fire Trouble/Fire Trouble Restore
HA/HR Holdup Alarm/Holdup Restoral
GA/GR Gas Alarm/Gas Restoral
FT/FJ Fire Trouble/Fire Trouble Restore
LT/LR Phone Line Trouble/Phone Line Restoral
OA Automatic Opening
OC Cancel Report
OP Opening Report
OQ Remote Opening
PA Panic Alarm
RP Automatic Test
RX Manual Test
TA/TH Tamper Alarm/Tamper Alarm Restore
TJ Tamper Trouble Restore
TS/TE Test Start/Test End
TT Tamper Trouble
UA Untyped Zone Alarm
UB/UU Untyped Zone Bypass/Untyped Zone Unbypass
UT/UJ Untyped Zone Trouble/Restore
XG/XH RF Interference/RF Interference Restore
XT/XR Transmitter Battery Trouble/Transmitter Battery Restoral
YT/YR System Battery Trouble/System Battery Restoral
*If APL is enabled, AlarmNet will generate a special comm. fail
message (E316) if it does not hear from a unit within 15 minutes
after a delayed alarm is delivered. This message is meant to alert
the Central Station that the system has been tampered with and
may have been compromised.
- 58 -
Definition