System Type; Program The Communications Module - Honeywell L5210 Series Installation And Startup Manual

LYNX Touch Installation and Setup Guide
Programming the Control
Refer to the LYNX Touch L5210/L7000 Programming Guide (p/n 800-19976) or the LYNX Touch L5210CN/L7000 CN
Programming Guide (p/n 800-20379) for additional information regarding programming options.

System Type

The following system options are programmed in this section:
Option
RF Jam Enable or disable RF Jam Log and Reporting
Speaker Phone Enable or disable Speaker Phone mode. (Only available on the LYNX Touch L5210/L5210CN)
Two Way Voice Enable or disable Two Way Voice communication with the Central Station.
RF House Code Set RF House Code. (Bi-directional RF Devices)
Remote Phone Enable or disable Remote Phone Control mode. (Only available on the LYNX Touch L5210/
L5210CN)
Phone Notification Enable or disable Phone Notification mode. (Phone Line-cut) (Only available on the LYNX Touch
L5210/L5210CN)
Phone Detect Time Select a delay period between phone line-cut & system response (allows phone to restore) (Only
available on the LYNX Touch L5210/ L5210CN)
Note: This field is displayed if Phone Notification is enabled.
Events Enable or disable multiple options for event logging (i.e.; alarms, troubles, open/close, bypass, all)
Non-Security Enable or disable non-security event logging
Remote Access Enable or disable end user to access their system via a website
Serial
Multi Mode Serial Enable or disable transmission of panel status events via email (Active only when Remote Access
Serial is enabled)

Program the Communications Module

A router is required if you are installing the L5100-WiFi module. The router must be powered on and
connected for Wi-Fi operation (alarm reporting) to occur.
The following system options are programmed in this section:
Option
Communications Path
APL
City ID
CS ID
Sub ID
Supervision
Old Alarm Time
Remote Acc. Comm.
Multi Mode Comm.
IP Fault Time
Use DHCP
NIC IP Address
Subnet Mask
Gateway IP Address
DNS Server IP Address
Cell Fault Time
Cell Rollover
Cell 24 Hour Test
Remote Access (Total Connect) and Multi Mode (PSD) over Wi-Fi, IP or Cellular cannot be enabled in the panel
alone. Availability of this service is controlled via the web-based programming tool on the AlarmNet 360 website.
These features must to be enabled through the AlarmNet 360 website first and transferred to the device.
Selects type of Communications Module
Enables Advanced Protection Logic
Enter Central Station Primary City ID
Enter Primary Central Station ID
Enter Central Station Primary Subscriber ID
Selects how often the Communications Module sends supervisory messages to the Central Sta.
Selects how long an undeliverable alarm delivery is retried to the Central Station.
Enables or disables user remote access via internet and/or Cellular.
(appears only if Remote Access IP or Cellular is enabled.) Enables/disables multi mode feature.
(Appears only if IP or WiFi is enabled in Communications Path field.) Selects time delay before
the Communications Module notifies the Control Panel of a loss of contact with the internet.
Dynamically selects the IP addresses
(Appears only if "No" is selected in Use DHCP field.) Enter NIC IP Address.
(Appears only if "No" is selected in Use DHCP field.) Enter Subnet Address.
(Appears only if "No" is selected in Use DHCP field.) Enter Gateway IP Address
(Appears only if "No" is selected in Use DHCP field.) Enter Domain Name Server IP Address.
(Appears only if Cellular is enabled in Communications Path field.) Selects time delay before the
Communications Module notifies the Control Panel of a loss of contact with the network.
If enabled, all reports including supervisory messages are sent over the cellular path in the event
of an Internet failure. If disabled, all reports excluding supervisory messages are sent over the
cellular path in the event of an Internet. (Appears only if "WiFi & Cellular" is selected as the
Communications Path.)
Enables daily test of Cellular module operation. (Appears only if "WiFi & Cellular" is selected as
the Communications Path.)
Function
Function
- 28 -