5800 Series Transmitter Loop Numbers - Honeywell LYNX Touch Series Installation And Setup Manual

5800 Series Transmitter Loop Numbers

(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP
1
LOOP
1
5 8 0 0 C O 5 8 0 0 M i c r a
E N R O L L A S " R F " E N R O L L A S " R F "
LOOP
1 LOOP
1
5 8 0 0 S S 1
5 8 0 0 WAV E
E N RO L L A S " R F "
P RO G R A M
H O U S E I D
SERIAL #1
LOOP 3
SERIAL #1
O N
LOOP 2
O F
F
SERIAL #1
1
2
LOOP 4
SERIAL #1
3
LOOP 1
SERIAL #2
4
LOOP 3
SERIAL #2
LOOP 2
SERIAL #2 - LOOP 1 = ON + 4 BUTTONS
LOOP 4 = 3 + 4 BUTTONS
5 8 0 5 - 6
ENROLL AS "BR"
LOOP 2
(REED)
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
5 8 1 6 T E M P
5 8 1 6 M N
ENROLL AS "RF"
ENROLL AS "RF"
LOOPS
LOOP 3
1 - 3
5 8 2 2 T
5 8 2 1
ENROLL AS "RF" ENROLL AS "RF"
SERIAL #1
LOOP 3
A W
A Y
SERIAL #1
S T
A Y
LOOP 4
1
2
SERIAL #2
3
4
LOOP 3
5 8 7 8
5 8 7 7 ENROLL AS "BR"
Notes: (1)
The 5806W3 smoke detector must be used in SIA applications.
(2) Button type (BR) devices send only fault and low battery signals; no restore or check-in signals.
Supervised RF (RF) devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised RF (UR) devices send periodic check-in signals, faults, restore and low battery signals but the control does not
supervise the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go/No-Go Test Mode. Refer
to the transmitter's Installation Instruction for complete details. The system will confirm the enrollment of the encrypted device
by beeping two times
UL
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5814, 5816TEMP, 5819, 5819S(WHS & BRS), and
5828/5828V wireless transmitters
LOOP 1
5 8 0 0 P I R - R E S
E N R O L L A S " R F "
LOOP 1
5 8 0 2 M N
ENROLL AS
"UR" OR "RF"
LOOP 1
5806/5806W3/5807
5809
5808/5808LST/5808W3
ENROLL AS "RF"
ENROLL AS "RF"
LOOP 1
(PRIMARY)
LOOP 2
(AUX.
CENTER)
LOOP 1
(TEMP LOOP 3
SENSOR) (AUX.
RIGHT)
5 8 1 7
ENROLL AS "RF" ENROLL AS "RF"
SERIAL #1
LOOP 3
AR
M ED
SERIAL #2
R EA
D Y
LOOP 3
M IC
M ES
SA GE
SERIAL #1
LOOP 4
SERIAL #2
LOOP 2
5 8 2 8 / 5 8 2 8 V
P RO G R A M
HOUSE ID
LOOP 1
(MOTION)
SERIAL #1
LOOP 2
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
5 8 9 0 / 5 8 9 0 P I
ENROLL AS "RF"
have not been evaluated by UL
LYNX Touch Installation and Setup Guide
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 P I R / 5 8 0 0 P I R - O D
5 8 0 0 P I R - C O M E N R O L L A S " R F "
E N R O L L A S " R F "
O N
LOOP 4 O F
F
LOOP 1
5 8 0 2 M N 2 5804/5804E
ENROLL AS ENROLL AS "BR"
"UR" OR "RF"
LOOP 1 LOOP 1
LOOP 1
5 8 1 1
E N R O L L A S " R F "
LOOP 2
(REED)
LOOP 3
LOOP 1
(TERMINALS)
LOOP 1
(TERMINALS)
5 8 1 8 5 8 1 9
ENROLL AS "RF"
SERIAL #2
LOOP 1
SERIAL #1
LOOP 2
SERIAL #2
LOOP 4
SERIAL #1
LOOP 1
5834-4 5 8 5 3
ENROLL AS "BR" ENROLL AS "RF"
LOOP 1
5 8 9 4 P I
5897
ENROLL AS "RF" ENROLL AS "RF"
.
- 15 -
Installing Wireless Zones
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 R L
S E T
H O U S E I D
LOOP 3
LOOP 2
LOOP 2
LOOP 4
LOOP 1
LOOP
3 LOOP 1
•
• •
•• •
• • ••
• •
•
•
5 8 0 4 B D / 5 8 0 4 B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
LOOP 2
(REED)
LOOP 1
(TERMINALS)
5814
5 8 1 6
ENROLL
AS "RF" ENROLL AS "RF"
LOOP 2
(REED)
LOOP 3
LOOP 1
(TERMINALS)
LOOP 1
(INTERNAL
SHOCK
SENSOR
5 8 2 0 L
5 8 1 9 S ( W H S & B R S )
ENROLL AS "RF" ENROLL AS "RF"
LOOP 1
(HIGH
SECURITY)
LOOP 1
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
5870API LOOP 4 (TAMPER)
ENROLL AS "RF"
LOOP 1
(LOW SENSITIVITY)
LOOP 2
LOOP 1
(HIGH SENSITIVITY)
5 8 9 8
ENROLL AS "RF"