5800 Series Transmitter Loop Numbers - Honeywell L5210 Series Installation And Startup Manual

5800 Series Transmitter Loop Numbers

(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP
1
LOOP
1
5 8 0 0 C O 5 8 0 0 M i c r a
E N R O L L A S
E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
LOOP
1 LOOP
1
5 8 0 0 WAV E
5 8 0 0 S S 1
P RO G R A M
E N R O L L A S
S U P E R V I S E D H O U S E I D
LOOP 2
(REED)
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
5 8 1 6 5 8 1 6 M N
E N R O L L A S E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
A R
M E
D
R E
A D
Y
M IC
M ES
SA G
E
LOOP 3
5 8 2 2 T
5 8 2 8 / 5 8 2 8 V
E N R O L L A S P RO G R A M
S U P E R V I S E D HOUSE ID
SERIAL #1
LOOP 3
SERIAL #1
A W
A Y
LOOP 2
SERIAL #1
S T
A Y
LOOP 4
1
2
SERIAL #1
SERIAL #2
3
LOOP 1
LOOP 3 4
SERIAL #2
LOOP 2
5 8 7 8
ENROLL AS BUTTON E N R O L L A S
S U P E R V I S E D
Notes: (1)
The 5806W3 smoke detector must be used in SIA applications.
(2) Button type devices send only fault and low battery signals; no restore or check-in signals.
Supervised devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised devices send periodic check-in signals, faults, restore and low battery signals but the control does not supervise
the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go-No-Go Test Mode. Refer
to the transmitter's Installation Instructions for complete details. The system will confirm the enrollment of the encrypted device
by beeping two times
(5) The 5800PIR-OD, 5800RL, 5800SS1, 5804E, 5814, 5821, 5828/5828V, 5877, and 5878 wireless transmitters have not been
evaluated by ETL.
LOOP 1
5 8 0 0 P I R - R E S
E N R O L L A S
S U P E R V I S E D
LOOP 3
O N
LOOP 4 LOOP 2
O F
F
LOOP 1
5804E
ENROLL AS BUTTON
LOOP 2
(REED)
LOOP 1
(TERMINALS)
LOOP 1
(TERMINALS)
(TERMINALS)
5 8 1 8 M N L
E N R O L L A S
S U P E R V I S E D
SERIAL #2
LOOP 1
SERIAL #2
LOOP 3
SERIAL #2
LOOP 4
SERIAL #1
LOOP 4
SERIAL #1
LOOP 1
SERIAL #2
LOOP 2
5834-4
ENROLL AS BUTTON
LOOP 1
(LOW SENSITIVITY)
LOOP 2
(HIGH SENSITIVITY)
5 8 9 8
LYNX Touch Installation and Setup Guide
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 P I R / 5 8 0 0 P I R - C O M
E N R O L L A S
S U P E R V I S E D
LOOP 1
5809
5806/5806W3/5807
5808/5808LST/5808W3 E N R O L L A S
E N R O L L A S S U P E R V I S E D
S U P E R V I S E D
LOOP 2
LOOP 2
(REED)
(REED)
LOOP 3
(TERMINALS)
LOOP 3
LOOP 1
(INTERNAL
SHOCK
LOOP 1
SENSOR
5 8 1 9 S ( W H S & B R S )
5 8 1 9
E N R O L L A S E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
LOOP 1
5 8 5 3 5869
E N R O L L A S E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
- 19 -
Installing Wireless Zones
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 P I R - O D
E N R O L L A S
S U P E R V I S E D
LOOP 1
LOOP 1
LOOP 1
5 8 1 1
E N R O L L A S
S U P E R V I S E D
LOOP 1
5 8 2 0 L
E N R O L L A S
S U P E R V I S E D
S U P E R V I S E D
LOOP 1
(HIGH
SECURITY)
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
LOOP 4 (TAMPER)
5870API
E N R O L L A S
S U P E R V I S E D
5 8 0 0 R L
S E T H O U S E I D
5814
E N R O L L A S
S U P E R V I S E D
LOOPS
1 - 3
5 8 2 1
E N R O L L A S
5 8 7 7