5800 Series Transmitter Loop Numbers - Honeywell L5210 Series Installation And Setup Manual

5800 Series Transmitter Loop Numbers

(Refer to this information when programming transmitters)
The following illustration shows the compatible transmitters, their associated input types and loop
designations.
LOOP
1
LOOP
1
5 8 0 0 C O 5 8 0 0 M i c r a
E N R O L L A S E N R O L L A S
S U P E R V I S E D
S U P E R V I S E D
LOOP
1 LOOP
5 8 0 0 S S 1 5 8 0 0 WAV E
P RO G R A M
E N R O L L A S
S U P E R V I S E D H O U S E I D
LOOP 2
(REED)
LOOP 1
(TERMINALS)
LOOP 1
5814 5 8 1 6
E N R O L L A S
E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
LOOPS
LOOP 3
1 - 3
5 8 2 1 5 8 2 2 T
E N R O L L A S E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
LOOP 1
(HIGH
SECURITY)
LOOP 2
(STANDARD
SECURITY)
LOOP 3 (TILT MODE)
LOOP 4 (TAMPER)
5870API
E N R O L L A S
S U P E R V I S E D
Notes: (1)
The 5806W3 smoke detector must be used in SIA applications.
(2) Button type devices send only fault and low battery signals; no restore or check-in signals.
Supervised devices send periodic check-in signals, faults, restore and low battery signals.
Unsupervised devices send periodic check-in signals, faults, restore and low battery signals but the control does not supervise
the check-in signals.
(3) If an external sounder is required, the 5800WAVE should be used.
(4) The 5804E and 5834-4 encrypted (High-Security) devices must be activated while the system is in Go-No-Go Test Mode. Refer
to the transmitter's Installation Instructions for complete details. The system will confirm the enrollment of the encrypted device
by beeping two times
(5) The 5800PIR-OD, 5800RL, 5800SS1, 5804E, 5804BD, 5804BDV, 5814, 5816TEMP, 5821, 5828/5828V, 5877, and 5878
wireless transmitters have not been evaluated by UL/ETL.
LOOP 1
5 8 0 0 P I R - R E S
E N R O L L A S
S U P E R V I S E D
LOOP 3
O N
LOOP 4 LOOP 2
O F
F
LOOP 1
1
5804E
ENROLL AS BUTTON
LOOP 2
(REED)
LOOP 1
(TERMINALS)
ALTERNATE
POSITION
FOR LOOP 2
5 8 1 6 M N
E N R O L L A S
S U P E R V I S E D
SERIAL #1
LOOP 3
A R
M E
D
R E
A D
Y
M IC
M ES
SA G
E
5 8 2 8 / 5 8 2 8 V
P RO G R A M
HOUSE ID
SERIAL #1
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 3
5 8 7 7
ENROLL AS BUTTON
LYNX Touch Installation and Setup Guide
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 P I R / 5 8 0 0 P I R - C O M
E N R O L L A S
S U P E R V I S E D
LOOP 2
LOOP 4
LOOP
3 LOOP 1
•
• •
•• •
• • ••
• •
• •
5 8 0 4 B D / 5 8 0 4 B DV 5806/5806W3/5807
ENROLL AS BUTTON 5808/5808LST/5808W3
PROGRAM HOUSE ID E N R O L L A S
S U P E R V I S E D
LOOP 2
(REED)
LOOP 3
LOOP 1
(TERMINALS)
LOOP 1
(TERMINALS)
5 8 1 8 M N L
E N R O L L A S E N R O L L A S
S U P E R V I S E D S U P E R V I S E D
SERIAL #2
LOOP 1
SERIAL #1
LOOP 2
SERIAL #2
LOOP 3
SERIAL #1
LOOP 4
SERIAL #2
LOOP 2
5834-2
ENROLL AS BUTTON ENROLL AS BUTTON
SERIAL #1
A W
A Y
LOOP 2
S T
A Y
1
2
SERIAL #1
3
LOOP 1
4
SERIAL #2
LOOP 2
5 8 7 8
5 8 9 8
E N R O L L A S
S U P E R V I S E D
- 19 -
Installing Wireless Zones
LOOP 1
(LOW
SENSITIVITY
LOOP 2
(HIGH
SENSITIVITY)
LOOP 3 (TEMP)
LOOP 4 (TAMPER)
5 8 0 0 P I R - O D
E N R O L L A S
S U P E R V I S E D
LOOP 1
LOOP 1
5809
E N R O L L A S
S U P E R V I S E D
LOOP 2
(REED)
LOOP 3
(TERMINALS)
LOOP 1
(INTERNAL
SHOCK
SENSOR
5 8 1 9 5 8 1 9 S ( W H S & B R S )
E N R O L L A S
S U P E R V I S E D
SERIAL #2
LOOP 1
LOOP 1
SERIAL #2
LOOP 4
SERIAL #1
LOOP 1
5834-4 5 8 5 3
E N R O L L A S
S U P E R V I S E D
LOOP 1
(LOW SENSITIVITY)
LOOP 2
(HIGH SENSITIVITY)
5 8 0 0 R L
S E T H O U S E I D
LOOP 1
5 8 1 1
E N R O L L A S
S U P E R V I S E D
LOOP 1
5 8 2 0 L
E N R O L L A S
S U P E R V I S E D
5869
E N R O L L A S
S U P E R V I S E D