List Of Num; Setting Of Ncu Parameters; Tone/Pulse - Canon L100 Service Manual

List of NUM

Numeric parameter setting mode
No. Parameter
001 Not in use
002 RTN transmission criteria X
003 RTN transmission criteria n
004 RTN transmission criteria m
005 NCC pause (before ID code)
006 NCC pause (after ID code)
007 - 009 Not in use
010 T.30 T0 timer
011 T.30 T1 timer (for incoming transmission)
012 Maximum incoming lines
013 T.30 EOL timer
014 Not in use
015 Threshold between hokking nad on-hook
016 Lead time to the first response when switching between
FAX and TEL
017 Duration to activate pseudo-RBT cadence
018 Duration to deactivate pseudo-RBT cadence (short)
019 Duration to deactivate pseudo-RBT cadence (long)
020 Duration to activate pseudo-ring cadence
021 Duration to deactivate OFF Hook cadence (short)
022 Duration to deactivate OFF Hook cadence (long)
023 CNG detection level when switching between FAX and
TEL
024 Pseudo-RBT outgoing level when switching between
FAX and TEL
025 CNG monitor duration while the answering device is
activated
026 No signal detection level while the answering device is
activated
027 Duration to detect preamble of V21 low-speed flag
028 - 050 Not in use
051 Threshold to detect hook
052 Not in use
053 Set DTMF calling counts when receiving FAX remotely 10 to 9999 (default 25)
054 Set Busy Tone outgoing duration when using handset
055 - 080 Not in use
8
Service Mode > FAX > Setting of NCU Parameters > TONE/PULSE
Allowable setting range
1 to 99 %
2 to 99 times
1 to 99 lines
1 to 60 sec
1 to 60 sec
55 sec principally
0 to 9999
(France: 3500, Others: 3000)
0 to 65535 (line)
0: without limitation
500 to 3000
(set to 55 sec by default)
0 to 999
0 to 9
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0 to 999
0 to 7
10 to 20 (100 V)
0 to 20 (120, 230 V)
0 to 999
0 to 7
20 (*10 ms)
10 to 9999
T-8-22
8 Service Mode > FAX > Setting of NCU Parameters > TONE/PULSE

Setting of NCU Parameters

■ TONE/PULSE

Operation Method
1) Setting of Tone Parameters
While "#NCU" is displayed, press "OK" key -> Select "#TONE" and press "OK" key so that
it becomes tone parameter setting mode.
2) Setting of Pulse Parameters
While "#NCU" is displayed, press "OK" key -> Select "#PULSE" and press "OK" key so that
it becomes pulse parameter setting mode.
Item
TONE 001; Tone signal sending time (PSTN)
002; Minimum pause time (PSTN)
PULSE FORM Pulse digit format
001; Pulse dial speed (10 pps)
002; Pulse dial speed (20 pps)
003; Pulse dial make ratio
004; Minimum pause time
DIALTONE
● Bit Switch
Bit No. Function
Bit 0 Frequency detection method Modem
Bit 1 Not in use
Bit 2 Signal frequency Changed
Bit 3 Not in use
Bit 4 Judgment of intermittent signal start from valid ON signal start from either valid ON
Bit 5 Not in use
Bit 6 Signal form Continuous
Bit 7 Signal detection Detected
● Numeric value parameter
Parameter No. Function
001; T0 timer
002; T1 timer
003; T2 timer
004; T3 timer
Function Setting range
10 to 9999 (msec)
10 to 9999 (msec)
0 -> DP (N)
1 -> DP (N+1)
2 -> DP (10-N)
5 to 300 (x0.1 pps)
5 to 300 (x0.1 pps)
10 to 90 (%)
10 to 9999 (msec)
1 0
Tonal counter
- -
Not changed
- -
signal or OFF signal
- -
Intermittent
Not detected
T-8-24
Setting range
0 to 9999 (x 10 msec)
0 to 9999 (x 10 msec)
0 to 9999 (x 10 msec)
0 to 9999 (x 10 msec)
8-11
T-8-23
8-11