Rf Key Fob Programming; Rf Key Fob Programming Outline; Rf Key Fob Summary Screen - 2gig Technologies Go!Control 2GIG-CNTRL2 Installation & Programming Instructions

Installer Programming

RF Key Fob Programming

RF Key Fob Programming Outline

The Control Panel can be programmed with up to eight RF remote
control key fobs.
Programming the RF key fobs into the Control Panel involves
selecting the sensor number for a particular device, setting or
learning the RF key fob's serial number, and selecting the other
options for the sensor.
• RF key fobs #1 - #8 report as system sensors #51 - #58
for opening/closing, emergency, and low battery reports.
RF KEY FOB REPORTING CODES
RF key fob #1
RF key fob #2
RF key fob #3
RF key fob #4
RF key fob #5
RF key fob #6
RF key fob #7
RF key fob #8
Refer to Figure 54 for an outline of the steps required to program
RF key fobs into the Control Panel. The options that can be set for
each RF key fob are:
• Key Fob Number — Key fob number 1-8
• Key Fob Used — Key fob used or not
• Key Fob Equipment Code — Key fob model
• Key Fob Other Equipment Code — Enter special
equipment code (only shown for key fobs set as "other")
• Key Fob Serial # — Serial number labeled on key
fob; hand enter or "learn" by sending signal
• Key Fob Equipment Age — New unit or existing key fob
• Key Fob Emergency Key — Choose
function of double-press on top buttons
• Key Fob Can Disarm — Choose whether a
key fob is allowed to disarm the system
• Key Fob Voice Descriptor — Name assigned to the key fob
• Key Fob Arm No Delay — Choose if key fob
will arm instantly without an Exit Delay
• Key Fob Key 4 Output — Select action
for key fob auxiliary button

RF Key Fob Summary Screen

After setting all the options for a sensor, the key fob summary screen
is displayed. The screen can also be displayed for programmed key
fobs during key fob program editing by pressing the SUM button.
• The ← and → arrow buttons step through the key fob numbers.
• The EDIT CURRENT and EDIT NEXT buttons return to key fob
programming.
• Pressing SKIP goes to question Q-4 (RF keypad programming).
Figure 53. Key Fob Summary Screen
26
Reports as sensor #51
Reports as sensor #52
Reports as sensor #53
Reports as sensor #54
Reports as sensor #55
Reports as sensor #56
Reports as sensor #57
Reports as sensor #58
KEY FOB PROGRAMMING (Q-3) OUTLINE
STEP DOWN
THROUGH OPTIONS
SELECT KEY FOB #
PRESS FOR NEXT OPTION
SELECT KEY FOB
USED
PRESS FOR NEXT OPTION
SELECT KEY FOB
EQUIPMENT CODE
PRESS FOR NEXT OPTION
ENTER KEY FOB
OTHER EQUIPMENT CODE
(ONLY FOR "OTHER" EQUIPMENT)
PRESS FOR NEXT OPTION
ENTER KEY FOB
SERIAL NUMBER
PRESS FOR NEXT OPTION
SELECT KEY FOB
EQUIPMENT AGE
PRESS FOR NEXT OPTION
SELECT KEY FOB
EMERGENCY KEY
PRESS FOR NEXT OPTION
SELECT KEY FOB
KEY 2 CAN DISARM
PRESS FOR NEXT OPTION
CONSTRUCT KEY FOB
VOICE DESCRIPTOR
PRESS FOR NEXT OPTION
SELECT KEY FOB
ARM NO DELAY
PRESS FOR NEXT OPTION
SELECT KEY FOB
KEY 4 OUTPUT
PRESS TO FINISH FOR THIS SENSOR, THEN
Figure 54. Key Fob Programming Outline
SELECT OPTION WITH
THESE KEYS
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
OR PRESS SKIP TO JUMP TO Q-4
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD
ENTER ON KEYPAD OR PRESS
shift learn
THEN
AND SEND SIGNAL FROM SENSOR
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
PRESS insert FOR EACH WORD
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
ENTER ON KEYPAD OR PRESS
OR
TO SELECT FROM LIST
edit
FOR NEXT SENSOR, OR FOR Q4
skip
next