Installation Requirements; Tools And Parts; Optional Pedestal; Location Requirements - Kenmore 110.42822200 User Manual

Section One
Parts supplied:
n_
1 - F
\-_-r
Beaded strap
i t
f . 1
lf You Have
Laundry tub or
standpipe taller
than 96 in. (2.4 m)
Overhead sewer
Floor drain
Drain hose too shoil
Waterfaucets beyond
reach of fill hoses
lf You Have You Will Need
to Buy
Sump pump system (if not al-
ready available)
Standard 20 gal. (76 L),30 in.
(76.2 cm) tall drain tub or util-
ity sink and sump pump (avail-
able f rom local plumbing sup-
pliers)
Siphon break, Part Number
285834; add itional d rain hose
P a r t N u m b e r 8 3 1 8 1 5 5 ; a n d
c o n n e c t o r k i t , P a r t N u m b e r
285835
Drain hose extension kit, Part
Number 285863
2 longer water fill hoses:
6 f t . ( 1 . 8 m ) P a r t N u m b e r
76314,10ft. (3.0 m)Part Num-
ber 350008
I NSTALLATI ON CONSI DERATIONS
INSTALLATION
REQUIREMENTS
Tools and Parts
Assemble the necessary tools and supplies before be-
ginning the washer installation. The parts supplied are
in the washer drum.
Tools needed for connecting the water inlet hoses
.
Pliers (that open to 1 9/16 in. [39.5 mm])
.
Flashlight(optional)
Tools needed for installation
.
O p e n e n d w r e n c h 5 / 8 i n . ( 1 7 m m ) a n d % i n . ( 1 3
mm)
.
Level
.
Wood block (2" x 4")
.
Ruler or measuring tape
Transport bolt hole plug
(4)
Alternate Parts You May Need
Parts listed are available from your local Sears slore
or Sears Service Center.
Optional Pedestal
A pedestal may be purchased separately for this
w a s h e r . T h i s p e d e s t a l w i l l a d d a b o u t 1 4 i n c h e s t o t h e
height of your unit for a total vertical height of approxi-
mately 52 inches (132 cm).
Optional Pedestal
This pedestal is available in three colors:
White - Part Number 4282
Bisque - Part Number 4284
Graphite - Part Number 4286
To order, call your local Sears store or Sears Service
Center.
Location Requirements
Selecting the proper location for your washer improves
performance and minimizes noise and possible washer
"walk."
Your washer can be installed under a custom counter,
or in a basement, laundry room, closet, or recessed
area. (See "Drain System.")
Companion appliance location requirements should
also be considered. Proper installation is your respon-
sibility.
You willneed
.
A water heater set to deliver 120'F (49'C)water
to lhe washer.
.
A grounded electricaloutlet
located within 5 ft.
(1 .5 m) of where the power cord is attached to the
back of the washer. (See "Electrical Require-
ments.")
.
Hot and cold water faucets located within 4 ft.
(1.2 m) of the hot and cold water fill valves, and
water pressure of 20-100 psi (137.9-689.6
kPa).
.
A levelfloor with a maximum slope of 1 in.
(2.5 cm) under entire washer. Installing the washer
on carpeting is not recommended.
.
A sturdy and solid f loor to support the washer with
a total weight (water and load) of 400 lbs. (180
kg).
Do not operate your washer in temperatures below
32'F (0"C). Some watercan remain in the washerand
can cause damage in low temperatures.
1 - 1