Conventions Used In This Manual - Gemini GEM-P9600 Programming Instructions Manual

WI 1185 6/03
The displays shown on the previous pages will appear after a brief delay.
Direct Address Programming Example
!
Use to toggle the cursor between the 4-digit address field and the data entry locations.
R
Example: Program Zones 6, 7 and 8 as Exit/Entry Follower Zones.
!
Enter the address directly using the number buttons.
DETERMINE THE DATA ENTRIES
!
!
The contents of the address will be read automatically, along with the feature name and programming information.
1. Referring to ZONE FEATURES in the Programming Worksheets that follow, Exit/Entry Follower for Zones 5
The cursor will advance to the data field. Enter the required data directly using the number buttons.
through 8 are located at address 0506, left digit. Circle
! U
Press to save the contents of each address.
!
2. Add the data values for Zones 6, 7 and 8: 2+4+8=14. From Tables 1 and 2, "14" (E) is entered as press
. The right digit (for Zones 1 through 4, none of which are Exit/Entry Follower Zones) is entered as a
G4
EXIT DIRECT ADDRESS PROGRAM MODE: When done, press
blank (•).
ZONE OPTION

CONVENTIONS USED IN THIS MANUAL

EXIT/ENTRY FOLLOWER
The Keypad Programming Worksheets in the back are
provided as an address-programming reference to help
the installer modify his custom default program or to
PROGRAM THE DATA ENTRIES
make minor field alterations to an existing panel program.
!
It is recommended that the panel be uploaded to 1. Enter the panel's Dealer Security Code (Address 0500), then press
NAPCO's PCD-Windows software following any keypad
!
the button.
A
programming and that the PCD3000's error-check feature
be utilized to reduce the possibility of programming
!
2. Answer NO (
omissions or conflicts.
NOTE: If you pass "ACTIVATE PROGRAM", scroll backward using the the
Note: Most of the addresses shown comprise two data
entry locations, left and right digits.
!
3. Press the button to enter the Address Program Mode. Address "0000" will display.
C
digits on the left data-display segment, and the right digit
!
on the right segment. For those addresses having only
4. Press
0506
one programmable nibble, program the right segment
cursor will advance to the data field.
only; the left segment should display a blank (•).
!
5. Press
3 G 4
Keep the Keypad Programming Worksheets on file for
future reference.
! J
6. Press to save.
General Programming Steps
Address 1218 is now programmed with "E•".
!
1. Contact the central station to ascertain receiver
7. Enter another 4-digit address to continue programming or press
format, data format, event codes, subscriber numbers
and telephone number(s).
!
2. Select the desired features by circling
respective "address"
Programming Options and Worksheets for guidance
in selecting the "data" (1,2,4,8) to be entered into
those boxes.
!
3. Program the data entered in the boxes on the
worksheets into the respective addresses.
display will show the entry numerically, but will
display "0" for the number 10, and letters "B", "C",
"D", "E", and "F" for the numbers 11 through 15,
respectively. To program a 10, press
To program 11 through 15, press
through
G 5
NOTE: See the Direct Address Programming Example on the previous page.
L
NAPCO Security Systems
ZONES
LEFT DATA VALUES
SUM = 14 (CIRCLE
ZN08 ZN07 ZN06
$ # "
) to all questions until "ACTIVATE PROGRAM Y/N" is displayed; then press YES (
F
Program the left
to access Address 0506. The data for both digits will display and the
to enter an "E" in the left digit and press
"
boxes. Refer to
G 0
G 1
, respectively.
"
the data values for Zones 5–8.
to exit and resume normal keypad operation.
C
ADDRESS
"
)
0506
L ADDR
ZN05
E BLANK (•)
1 0460
DATA ENTRY SELECTIONS
"
(BINARY VALUE CIRCLED)
ENTER DATA
8 4 2
8 4 2
"
8 4
"
8 4
B
#
8 2
#
8 2
# "
8
# "
8
$
4 2
to enter a blank (•) in the right digit.
0
$
4 2
$ "
4
$ "
4
$ #
C
2
$ #
2
the
$ # "
the
$ # "
Table 1 (above). Determining data entry for a location
(each "nibble"). Numbers in parentheses indicate data for
The
selected zones
Worksheets that follow).
.
X
GEM-P9600 Programming Instructions
ZONES
RIGHT DATA VALUES
"
)
SUM = 0 (CIRCLE
R
ZN04 ZN03 ZN02 ZN01
8 4 2
ENTRY PRESS
" N
TOTAL
1 blank 0
!
1
1
2
1 2
!
3
3
button.
1 4 4
! 5 5
6
1 6
!
7
7
1 8 8
!
9 9
1 10 G 0
!
G 1
11
to exit and resume normal keypad
G 2
1 12
!
G 3
13
1 14 G 4
!
15 G 5
or features. (See
!
Page 25
1
KEYPAD
DISPLAYS
•
1
2
).
E
3
4
5
6
7
8
9
0
B
C
D
E
F
Programming